Description :
Tenders for Supply And Installation Of Open Gym Equipments Under Mplads Funds For Various Locations Of Parks In Municipal Corporation Of Delhi - Supply & Installation Of Open Gym Equipments Under Mplads Funds For Various Locations Of Parks In Municipal Corporation Of Delhi, Seated Puller /pull Chair Made From C Class G.i Pipe. Dimensions: - 1900mm (length) X 740mm (width) X 1920mm. (height). Safe Area:- 1.2mtr X 3mtr. Seated Puller Equipment Made Up Of C Class G.i. Pipe Of Different Nb.nb Stands For Nominal Bore Sizes I.e. Internal Diameter Of Pipe In Millimeters. The Center Pipe Is Of 100nb Made From C Class G.i. Pipe. Bottom Support Is Of M.s. Round Plate Of Dia 250 Mm & 10mm Thickness Welded. All Linkages Are Made Up Of 25nb C Class G.i. Pipe. The Handle Frame Is Of 32nb C Class G.i. Pipe. The Seat Frame Is Of 32nb C Class G.i. Pipe. To Build Structure Bushes Are Used Which Are Made From Seamless Pipe Of 60mm O.d. And 5mm Thickness As Well As 60mm Diameter Solid Bar Bush Used. The Foundation Used For Fixing Is A Structure And Made From Center Pipe Of G.i. Of 80 Nb C Class. Welded With M.s. Round Plate Of Dia 250 Mm & 10mm Thick. Main Pipe Supported With 25 Mm X 25mm M.s. Angles Of 3 Mm Thickness And 20mm X 40mm Crc Square Pipes Of 3mm Thickness. Foundation Cover Closing Cap Is Made From Injection Moulded Plastic Lldpe / Hdpe. The Seats And Back Rests Are Fitted On The Outer Frames Are Made Up Of M.s. Sheet Of Size 330 Mm X 300 Mmx2mm Thickness And Deep Drawn And Pressed In Tools And Dies To Have Uniform Radius Of 20 Mm With No Sharp Edges.closing Caps Are Made Up Of From Injection Moulded Plastic Lldpe / Hdpe.pins Used Of Diameter 25mm And 17mm Are Made Up From Sae 8620 Bright Material. The Bearings Used Are Of 6205 2rs1 And 6203 2rs1 Permanent Lubricated Sealed Bearing Of Reputed Brand.high Tensile Steel With Galvanized Nuts & Bolts Are Used For Assembly.thecirclips Used For Assembly Are Of A16. The Gym Equipment Shall Be Finished Smooth With A Primer Coating Of Atleast 40 Micron Followed By Epoxy Based Powder Coating With Polyster Powder Coating Of At Least 60 To 70 Micron Thickness Using Exonobel / Berger Make Paints Or Its Equivalent Paints. The Holding Down/fixing Of Gym Equipments Shall Be Emboded In Cement Concrete In The Ratio Of 1:2:4 (1cement : 2 Coarse Sand :4 Stone Agg. 20mm Nominal Size), Seated Puller /pull Chair Made From C Class G.i Pipe. Dimensions: - 1900mm (length) X 740mm (width) X 1920mm. (height). Safe Area:- 1.2mtr X 3mtr. Seated Puller Equipment Made Up Of C Class G.i. Pipe Of Different Nb.nb Stands For Nominal Bore Sizes I.e. Internal Diameter Of Pipe In Millimeters. The Center Pipe Is Of 100nb Made From C Class G.i. Pipe. Bottom Support Is Of M.s. Round Plate Of Dia 250 Mm & 10mm Thickness Welded. All Linkages Are Made Up Of 25nb C Class G.i. Pipe. The Handle Frame Is Of 32nb C Class G.i. Pipe. The Seat Frame Is Of 32nb C Class G.i. Pipe. To Build Structure Bushes Are Used Which Are Made From Seamless Pipe Of 60mm O.d. And 5mm Thickness As Well As 60mm Diameter Solid Bar Bush Used. The Foundation Used For Fixing Is A Structure And Made From Center Pipe Of G.i. Of 80 Nb C Class. Welded With M.s. Round Plate Of Dia 250 Mm & 10mm Thick. Main Pipe Supported With 25 Mm X 25mm M.s. Angles Of 3 Mm Thickness And 20mm X 40mm Crc Square Pipes Of 3mm Thickness. Foundation Cover Closing Cap Is Made From Injection Moulded Plastic Lldpe / Hdpe. The Seats And Back Rests Are Fitted On The Outer Frames Are Made Up Of M.s. Sheet Of Size 330 Mm X 300 Mmx2mm Thickness And Deep Drawn And Pressed In Tools And Dies To Have Uniform Radius Of 20 Mm With No Sharp Edges.closing Caps Are Made Up Of From Injection Moulded Plastic Lldpe / Hdpe.pins Used Of Diameter 25mm And 17mm Are Made Up From Sae 8620 Bright Material. The Bearings Used Are Of 6205 2rs1 And 6203 2rs1 Permanent Lubricated Sealed Bearing Of Reputed Brand.high Tensile Steel With Galvanized Nuts & Bolts Are Used For Assembly.thecirclips Used For A
