Description :
Tenders for Supply Of Spares For Bottom Ash Handling System Of Ash Plant - Unit No.3, 4 & 5 At Gandhinagar Tps. - Shoulder Bolt With Lock Plate For Assembling Part No.8 (part No.9) For 24" X 24" Feed Gate Assembly Of Bottom Ash System Unit- 3 And 4 As Per Dwg. No. 8743-2b-571., Cross Brace (part No.11) For 24" X 24" Feed Gate Assembly Of Bottom Ash System Unit- 3 And 4 As Per Dwg. No. 8743-2b-571., Resilient Gate Face P.no-2,for Bottom Ash Hopper,drg 8743/2b/571, Shoulder Bolt With Lock Plate For Assemblying Part No.8 (part No.9) Of 24x24 Squire Bottom Feed Gate Dwg.no. 95p10-t-2b-570 Of Unit No. 5, Cross Brace (part No.11) Of 24x24 Squire Bottom Feed Gate Dwg.no. 95p10-t-2b-570 Of Unit No. 5, Gate Face 1 Set Consists Of Ss:316 Gate Face With M.s Back Up Plate Of 24x24 Squire Bottom Feed Gate Of Unit No. 5, Cam Segment P.no-1 For 33"x30 Excen Crusher, Front Wear Plate/anvil Plate Of 33" X 30" Clinker Crusher / Grinder Assembly For Unit-3and4 (1 Set Equals To 3 Nos.)., Back Wear Plate/plate Combing (part No. 6) Of 33" X 30" Clinker Crusher / Grinder Assembly As Per Dwg. No. 8743-2b-582(rev-1) For Unit-3 And 4 (1 Set Equals To 3 Nos.)., Side Wear Plate(part No. 8) Of 33" X 30" Clinker Crusher / Grinder Assembly As Per Dwg. No. 8743-2b-582(rev-1) For Unit-3 And 4 (1 Set Equals To 2 Nos. Left Hand And 2 Nos. Right Hand Wear Plate)., Shaft With Shaft Structure And Shaft Sleeve Of 33" X 30" Clinker Crusher / Grinder Assembly For Unit-3 And 4., 33"x30" Single Roll Clinker Crusher / Grinder Complete Assembly Without Drive Arrangement, Fluid Coupling, Chain Drive And Driven Sprocket As Per Dwg. No.8743-2b-582(rev-1) For Unit-3and4, Feedsump Below Clinker Crusher For Unit No.3 And 4, Roll (cam Segment) 1 Setequals To 8 Nos. Cam Segment Of Single Roll Crusher For Unit No. 5, Front Wear Plate/anvil Plate (part No.3) 1 Set Consists Of 3 Nos B Front Wear Plate Of Single Roll Crusher Dwg.no.95p10-2b-582 (rev-1) For Unit No. 5, Back Wear Plate/plate Combing (part No.6) 1 Set Consists Of 3 Nos Back Wear Plate Of Single Roll Crusher Dwg.no.95p10-2b-582 (rev-1) For Unit No. 5, Side Wear Plate (part No.8) 1 Set Consists Of 2 Nos. Left Hand And 2 Nos Right Hand Type Of Single Roll Crusher Dwg.no.95p10-2b-582 (rev-1) For Unit No. 5, Shaft With Shaft Structure With Shaft Sleeve(part No.2 And15)for Clinker Grinder., Bearing Support (part No.8) Of Single Roll Crusher Dwg.no.95p10-2b-582 (rev-1) For Unit No. 5, Single Roll Crusher Complete Assembly Without Drive Arrangement,fluid Coupling,chain,drive And Driven Sprocket Of Single Roll Crusher Dwg.no.95p10-2b-582 (rev-1) For Unit No. 5, Feed Sump Of Bottom Ash System Of Unit - 5 As Per Drawing No. 95p10 - T - 1b - 711, Complete Assembly Of Feed Gate Housing With Feedgate, Access Door For Unit No.3 And 4, Bearing Housing Of Dcips Make 33" X 30" Clinker Crusher/grinder, Locking Plate For 600 Dia. Round Access Door For Bottom Ash Hopper, Nozzle With Ceramic Tip(part No. 2)tip Size- 36 Mm Of 8" Jet Pulsion Pump Assembly For Bottom Ash System Of Unit-3 And 4 As Per Dwg.no.8743 - 2b - 591(rev-1), Aligning Ring(part No. 10)of 8" Jet Pulsion Pump Assembly For Bottom Ash System Of Unit-3 And 4 As Per Dwg.no.8743 - 2b - 591(rev-1), Half Clamp(part No. 11)of 8" Jet Pulsion Pump Assembly For Bottom Ash System Of Unit-3 And 4 As Per Dwg.no.8743 - 2b - 591(rev-1) 1 Set Equals To 2 Nos., 9" Flange Clamp Half (part No. 18) Of 8" Jet Pulsion Pump Assembly For Bottom Ash System Of Unit-3 And 4 As Per Dwg.no.8743 - 2b - 591(rev-1) 1 Set Equals To 2 Nos., 8" Jet Pulsion Pump Complete Assembly Without Tail Pipe For Bottom Ash System Of Unit-3 And 4 As Per Dwg.no.8743 - 2b - 591(rev-1), Nozzle With Ceramic Tip Size 34 Mm Of Jet Pump For B.a System Dwg.no. 95p10-2b-591 (rev-1) For Unit No. 5, Aligning Ring (part No.10) Of Jet Pump For B.a System Dwg.no. 95p10-2b-591 (rev-1) For Unit No. 5, Half Clamp (part No.11) 1 Setequals To 2 Nos Of Jet Pump For B.a System Dwg.no. 95p10-2b-591 (rev-1) For Unit No. 5, 9" Flange Clamp Half (part No
