Meters Tenders

State Government

CTN :43312385

02 Jan, 2026 3.30 Lacs

Dalhousie - Himachal Pradesh

Tender For tender for repair and replacement of equipment at 33/11kv s/stn 2x5 mva sub -station dalhousie under electrical sub-division dalhousie. - 33/11kv s/stn 2x5 mva sub -station dalhousie under electrical sub-division dalhousie., complete overhauling of 4 outgoing feeder breaker trolley with repair & replacement of 4 nos. spring charge motors, tripping & closing coils , limit switch, indication bulb and other minor spare parts like lock spring, grease complete in all respect to make smooth opeartion of breaker., providing and fixing declo make spring, charge motor with gearbox and limit switch in 4 nos. breakers., providing and fitting of overcurrent & earth fault relay ashida 141c or cg 14n, providing & fixing of 3 mm 10% thick non-metallic, anti-static, fire retardant, low temperature resistant, acid/alkali resistant, high breakdown voltage min 33kv epoxy electric floor coating. coating conforming to class-c is 15652:2006. shall properly bond to the surface., providing & fixing digital ampere meter 30vdc rish dpm or equivalent.

corporations/Associations/Others

CTN :43343070

09 Jan, 2026 NA

Ludhiana - Punjab

Tender For purchase of measuring instrument ammeter(-/1a) single phase ,ammeter(-/1a) three phase ,ammeter(-/5a) three phase ,voltmeter(-/110v) single phase ,voltmeter(-/110v) three phase ,power factor meter(-/5a) single phase ,power factor meter(-/5a) three phase ,dc digital voltmeter ,multifunction meter(-/1a) ,multifunction meter(-/5a)

Private Sector

CTN :43335679

08 Jan, 2026 NA

Hyderabad-T - Telangana

Tender For procurement of laboratory equipment microbalance , autoclave , de-ioniser unit , centrifuge , total suspended solids apparatus , turbidity meter , magnetic stirrer , ph meter , hot air oven , muffle furnace , jar test apparatus , , ice flaker machine , ultrapure water purification system , high vacuum pump , heating mantle , sonicator , bacteriological incubator , colony counter , cod digestor , uv-vis spectrophotometer , orbital shaker & incubator , vortex shaker , fume hood , electrothermal heater , ultra-low temperature freezer , stack monitoring equipment , noise meter , rotospin , biosafety class ii cabinet , gas chromatography , fid/tcd/headspace) , chns-o analyzer , bomb calorimeter , icp-oes with mps , tkn analyser , optical microscope , microwave digestion system , ftir spectrometer , indoor air quality meters & particle size counter , portable / bench biogas analyzer (handheld) , gas leakage detector (portable) , gas flow meter / gas counter (wet-type or digital) , tedlar gas sampling bags + syringes & connectors , toc / doc analyser , cod digester + reagents (closed reflux) , incubator shaker / orbital shaker (cold room optional) , drying oven (forced air) with timer , ph / ec / orp / do (multi-parameter) meters , hotplate / magnetic stirrers, water bath , bench-top bioreactors / bmp setup (anaerobic , aas (atomic absorption spectrometer) , membrane filtration apparatus + vacuum pump

State Government

CTN :43335624

03 Jan, 2026 81.07 Lacs

Bengaluru - Karnataka

Tender For repairing of electrical works and providing lt feeder pillar box,meter panel board and street lights to the housing layout constructed under jnnurm-bsup scheme at sy.no.119 of varthuru in bangalore city.

State Government

CTN :43335633

03 Jan, 2026 75.60 Lacs

Bengaluru - Karnataka

Tender For repairing of electrical works and providing lt feeder pillar box,meter panel board and street lights to the housing layout constructed under jnnurm-bsup scheme at sy.no. 13 of nagareshwara nagenahalli in bangalore city.

State Government

CTN :43335645

03 Jan, 2026 1.64 Crore

Bengaluru - Karnataka

Tender For repairing of electrical works and providing lt feeder pillar box,meter panel board and street lights to the housing layout constructed under jnnurm-bsup scheme at sy.no. 53 of sadaramangala in bangalore city.

Central Government/Public Sector

CTN :42956361

02 Jan, 2026 61.87 Lacs

Rajouri - Jammu And Kashmir

Tender For corrigendum : provisioning of electrical and mechanical eqpt against ber under ge 862 ews - supply, installation, testing and commissioning of serve controlled voltage stabilizer (confirming to bis 9815 (part-1) 1994, reaffirmation 2019 latest version) three phase, four wire (rybn), 50 hz, naturally oil cooled, outdoor, unbalanced type, cooper wound, metallic body duly power coated with lifting hooks two nos, digital display type, relay free smooth and silent operation with 1st filling of transformer oil up to level having following specification:-(a) capacity 300 kva (b) type - suitable for unbalanced load and unbalanced input(c) input voltage -360v-480v, input frequency 50 hz (d) output voltage - stabilized at any deigned/ desired voltage 415/+-1% (e) rated frequency - 50 hz(f) wave form distortion - nil (g) response time - not to exceed 20 milli seconds(h) sensitivity - (+/-) 1% (j) rate of correction - not less than 6 volt/second between phase and neutral (k) efficiency - more than 95% (l) type of load - three phase, unbalanced type(m) metering - digital display voltmeter/ammeter with multi-functional meter (n) operating temperature - for indoor use upto max ambient temp + 55 c (o) dimmer rating - 450 amp (p) dimension of tanks - as per oem design(q) oil capacity- as per oem design , (r) class of insulation - class f (s) mode of operation automatic/manual (t) winding temperature rise - max 55 c (10 c above operating temp) (u) transformer oil -is 335 marked (v) core-crgo m4 grade/crno (cold roll grain oriented)/ (cold rolled non-oriented)(w) auto transformer (variac) -100 percent copper wound electrolytic grade(x) losses - as per is norms (y) power factor - not less than 0.95(z ) protection - (i) over load protections (ii) short circuit protections (iii) high/low voltage cut off (iv) by pass arrangement in case of emergency (v) single phase sequence change /phase fail protection (vi) earth fault protection(aa) standard fitting & accessories e.g marking plate, lifting lugs, ci rollers, earthing terminals, cable box including suitable platform as reqd on site complete all as as specified & directed., supply, installation, testing and commissioning of serve controlled voltage stabilizer (confirming to bis 9815 (part-1) 1994, reaffirmation 2019 latest version) three phase, four wire (rybn), 50 hz, naturally oil cooled, outdoor, unbalanced type, cooper wound, metallic body duly power coated with lifting hooks two nos, digital display type, relay free smooth and silent operation with 1st filling of transformer oil up to level having following specification:-(a) capacity 100 kva (b) type - suitable for unbalanced load and unbalanced input(c) input voltage -360v-480v, input frequency 50 hz (d) output voltage - stabilized at any deigned/ desired voltage 415/+-1% (e) rated frequency - 50 hz(f) wave form distortion - nil (g) response time - not to exceed 20 milli seconds(h) sensitivity - (+/-) 1% (j) rate of correction - not less than 6 volt/second between phase and neutral (k) efficiency - more than 95% (l) type of load - three phase, unbalanced type (m) metering - digital display voltmeter/ammeter with multi-functional meter (n) operating temperature - for indoor use upto max ambient temp + 55 c (o) dimmer rating - 150 amp (p) dimension of tanks - as per oem design(q) oil capacity- as per oem design , (r) class of insulation - class f (s) mode of operation automatic/manual (t) winding temperature rise - max 55 c (10 c above operating temp) (u) transformer oil -is 335 marked (v) core-crgo m4 grade/crno (cold roll grain oriented)/ (cold rolled non-oriented)(w) auto transformer (variac) -100 percent copper wound electrolytic grade(x) losses - as per is norms (y) power factor - not less than 0.95(z ) protection - (i) over load protections (ii) short circuit protections (iii) high/low voltage cut off (iv) by pass arrangement in case of emergency (v) single phase sequence change /phase fail protection (vi) earth fault protection(a

CTN :43274899

30 Dec, 2025 NA

Ranchi - Jharkhand

Tender For the supply of spare parts of vehicles and other equipment used in vehicle servicing on rate contract basis--c dynamo bracket, ac pump, temperature head unit, air filtter box, hydraulic cylinder piston, hydraulic cylinder rod, complete hydraulic cylinder, assembly, hydraulic pipe tank to cylinder, pto lever, pto lever kit, pto pump, pto seal kit, oil drain bolt, slip ring, hydraulic cylinder seal kit, hydraulic cylinder piston, hydraulic cylinder piston rod, complete hydraulic cylinder, assembly, main begin bearing, pressure switch rear, pressure switch front, mobile filter body, ecm complete, brake shoe lock, gear tappa, engine packing kit, rear axle bearing, clutch fork patti, mobile seperator, diesel returning jali pipe, silencer complete set, ecm complete, steering repairing kit, wiring harness complete, break vecamp, house pipe, slip ring, stator, stator coil, pulli, condensor, body aassembly upper & lower, patti fig, kit set, wiring harness, pinion, pinion gear, main bearing bering, water steel pipe, dynamo adjuster, finger kit, housing bolt 15-17-19 no, clutch paddel, gear handi, gear tappa, gear chainjer flang no-1-, 2/3/4/5 and back fork, gear frok swing boll, gear frok rod, gear chanzer kit, gear shaft katori, gear lattu, ring(kangan) bearing, gear box flange tapa, gear dry nut, tapa pinion washer, shaft bolt no- 17,15,19, center bearing flange, tel crown complete, crown handi cage, cage bolt, break adjuster kit, self parts, pinion, head unit, dynamo bracket, head seat, rear rubber pipe, cng reducer, hydraulic cylinder piston, hydraulic cylinder rod, complete hydraulic cylinder, assembly, hydraulic pipe pto to tank, hydraulic pipe tank to cylinder, anti dirt plug, pto pump, pto cable, slip ring, regulator cut out with carbon, electrifire set, startor, rotor, bearing, carbon plate, bearing plate, carbon, armature, carbon rocker, bearing bush, lever & frok, solenoid switch, armature lock, field coil, pinion lock, pinion, fan relay, heater timer, fuse box, fuse, head ligh & back light, head light bulb, head light holder clip, kilometer, hour meter, dashbord meter, terminal red, terminal balck, terminal mouth, ignition switch, heater plug, commination switch, head unit, horn patti, main glass with rubber guide, rubber guide, left & right side glass with rubber, guide, radiator fan, looking mirror, engine block, crank shaft, piston and pin, main bearing bering, connecting rod, connecting bush, cam shaft, oil pump complete, cam pinion, engine pully, timing plate, crank thrust washer, mobil chamber, crank pinion, timing oil seal, piston pin, engine full packing kit, stating pully, push rod, push guide, connecting bolt, engine chapa bolt, crank cam key, complete head, head wall, complete hub front, head guide oil seal, head seat, head gaskit, nozzle pipe, radiator, complete radiator

CTN :43322283

14 Jan, 2026 NA

Visakhapatnam - Andhra Pradesh

Tender For tender for supply of hose -20mm with threaded end connections , sock mount for main frame , jubilee clip 40mm , nut and bolt 12x100mm ss , level switch , hp flexible hose , victualic coupling , kit shaft seal , prefilter - filter pump shaft seal , filter pump , motor for 30tpd filter / prefilter pump , impeller 30.6id x 73 od x 9h , kit gaskets , cm 3-5 chamber complete p-4d , cm 3-5 pump shaft p-51 , cm 3-5 staybolt m8 p-181 , cm 3-5 kit gaskets , ring-circlips p-931 , casing p-1 , bearing lock out p-22 , bearing lock washer p-69 , cover gasket p-73 , constant level oiler p-77 , bolts p-171d , foot bolt p-171g , coupling , valve kit , seal.oil crankshaft , lockwasher , cap oil filler , gauge oil bubble w-gasket , o-ring crankcase cover , crank case , pin crosshead , seal oil crankcase , slinger barrier , retainer seal 2 pc , spacer lo-pressure seal , adapter male , springs coil , spacer w-coil springs , spacer v-packing , plug for priming , manifold discaharge , protector shaft wh screws , seal kit , o ring over hauling kit , victualing fitting , swash plate set , valve plate set , pulsation damper 0.16 lts. , o ring for head distriutor , sand filter , cartridge filter housing , lip seal dt module , membrane cushion , membrane cushion , pvc-u 2way solenoid vv d20 type160 nc , abs solvent cement , abs ball valve 2 way 25 mm , flow transmitter , o ring union 20 mm , o ring union 32 mm , o ring ball valve 25 mm 3-2 way pvc , connector 1 1-4 bsp m x 1 1-4 vivt , pu 4 hose , coupler for vict. coup.2.5 , pipe clamp 32 mm 2 bolt , elbow pu push in 1-4 mxpu4 qsl-1-4-6 , elbow pu push in fitting 1-4 fxpu4 , straight connector .1-4 m x pu 4 , solenoide valve , sol v-v 1-2 f230v 50hz ss316 2-way-no , two way ball valve with elec. actu. , control cabinet ro 200 , circuit breaker 1.6-2.5amp , pressure switch , miniature relay base for 2 c-o , servo motor control valve , control transformer 160 va , flow meter assembly , impeller grub screw , spacing pipe , spare kit d32 pvc , ball valve 2 way pvc-u 20 mm , dt module clamp , o-ring oil filler cap , edi module tool kit , oil gauge , hp elbow 1.for smcv , end connection flange brine and permeate , rubber hose 20mm , 325 mm long hose , 1650 mm long hose , pulsation damper , cartridge filter housing , cartridge filter element , lip seal dt module-groove ring gasket flange-sealing , air regulator , servo motor control valve , circuit breaker 1.6-2.5amp , miniature relay 24 vdc phoenix 2966171 , fuse base - 20 amp , pressure maintaining vlave , pressure switch , temperature indicator , circuit breakers 16 - 25 a , o-ring , o-ring , thermometer , 2 way ball valve assembly , 2 way ball valve ptfe d32 , ball valve abs 3 way d20 , pulley for motor , taper bush 1610 bore 24 mm , bearing hp pump , plunger rod , oil seal plunger rod , inlet valve adapter , oil drain kit , hp pump inlet manifold , frp filter type 1354 , head distributor , hp crank case oil , s.s. jubilee clips 22 mm to 30 mm , o ring crank case cover , high pressure hose module outlet , control transformer , emi filter mf 423-3-3d 200a , emi-emc choke mf 423-3-2d 200a , pressure transmitter 0-10 bar , level switch , conductivity sensor , conductivity electrode , flowmeter 40-400lph with magnetic float , lp hose 25mm idx1 bspmx500l ss316 , lp hose 32mm , h.p. flex. hose connecting hp pp and pi60 , hp hose of module in , h.p. hose module 1 to module 2 , hp hose sea water distribution manifold of dt module , lp hose hp pump inlet , hp hose discharge hose to dt manifold spool , taper bush 1615 bore 42mm , taper bush 2517 bore 42 mm , v belt , bearing hp pump motor , av mount for hp pp , av mount akcc 85m , mount for permeate transfer pump/filter pump , av mount akcc 40m , av mount for pk20 , hp pump crank case oil , jubilee clips 00 13mm to 20 mm , jubilee clips for d 25 , ss jubilee clips 2x 45 mm to 60 mm , support gravel 0.75 - 1.5 mm , support gravel 3.0 - 5.0 mm , support gravel1.52 - 3.0 mm , sand sup. fine 0.3 - 0.7mm , dolomite , pr

State Government

CTN :42971675

28 Dec, 2025 30.00 Lacs

Malegaon - Maharashtra

Tender For corrigendum : engagement of agency for monthly meter reading manual & through cmri and energy bill printing, bill distribution with data analysis, submission of raw data / xml (including load survey) in respect of power loom, industrial & commercial lt consumers having load above 20kw & some lt consumers having load below 20kw with amr/mri compatible meters in rsd sub division, dabhadi sub division and cco&m sub division under ucr division malegaon

By Cities

By States

By Agencies

By Ownerships

By Sectors