Tender For procurement of garo make compressors spares - list of item(s) / work(s) as per tender documents, cone,p/n:3116011127s, impeller-31160010679, impeller nut-31260010710, shaft sleeve-31360011567, lubrication ring ,p/n:31210006182, cone,comp,garo,ab850f,pn-002,3116010999s, cone,p/n:3110010999s,astm a 352 g,ab 850, impeller,p/n:31100008414,a352 gr.lcb, impeller nut,u/n:31210008814-ss, deflector p-side,garo,ab850f,pn.020, deflecter d-side,garo,ab850f,pn.021, wear ring,compr,part no.033, wear ring,compr,part no.034, complete set of gaskets, impeller nut,p/n:31260008814, shaft sleeve,p/n:31460011314, lubrication ring ,p/n:31210005606, deflector,pump side ,p/n:31260007860, deflector,driving side ,p/n:31260007861, complete set of gaskets, am 1100
Tender For bid to ras corrigendum : supply of control valve normal service for 2x800 mw ustpp mahan phase ii singrauli - asv-8 dea. pegging from aux. steam header , crhv-6 dea. pegging from crh line , cdv-26 main condensate control , cdv-23 low load condensate control , cdv-39 gsc min. flow recirculation , cdv- 43 excess return to cst , cdv-72 condensate for valve gland sealing , drv-2 and drv-8 hph-8a and 8b normal drain to hph-7a and 7b , drv-5 and drv-11 hph-8a and 8b alt. drain to ft-a , drv-15 and drv-22 hph-7a and 7b normal drain to deaerator , drv-18 and drv-25 hph-7a and 7b alt. drain to ft-a , drv-31 lph-3 alt. drain to ft-b , drv-48 deaerator overflow to ft-b , drv-53 and drv-59 hph-9a and 9b normal drain to hph-8a and 8b , drv-56 and drv-62 hph-9a and 9b alt. drain to ft-a , drv-65 lph-4 normal drain to lph-3 , drv-82 lph-5 normal drain to lph-4 , drv- 68 lph-4 alt. drain to ft-b , drv-85 lph-5 alt. drain to ft-b , dmv-43 dm normal mu to hotwell , drv-28 drip pump discharge control , asv-2 aux. steam to bfpts , crhv-2 crh steam to bfpts , dmcw-25 dmcw system for plant auxs , 1 by 4 inch ss tubing - 12 meter for each tag , ss fittings for connection to air filter regulator - for each tag , ss fittings for connection to air lock relay - for each tag , ss fittings for connection to ia header isolation valve - for each tag , ss equal tee - for each tag , ss 1 by 2 inch npt - m x 1 by 4 inch od tube connector - for each tag , commisioning spares - gaskets and gland packing , valve diagnostic and configuration software , cv test charges , pneumatic diaphragm for diaphragm actuated valve or equivalent item applicable for selected actuator type shall be provided - 2 nos. for each type of actuator , actuator seal kit for pneumatic cylinder actuated valve - 2 nos. for each type of actuator , gland packing - 1 set for each type of control valve , plug, seat, cage, stem etc. - 1 set for each type of control valve , retainer ring, seal ring etc. - 1 set for each type of control valve , gasket - 2 sets for each type of control valve , control valve or power cylinder positioner complete set - single acting - 10 percent of total quantity used in the system or minimum 2 nos. whichever is more for each type and model. , control valve or power cylinder positioner complete set - double acting - 10 percent of total quantity used in the system or minimum 2 nos. whichever is more for each type and model. , complete set of solenoid valve for pneumatic type on off valve or power cylinder - 2 nos. for each type and ratings , position limit switch for pneumatic type on off valve or power cylinder - 10 nos. for each type and ratings , air lock relay - 10 nos. for each type , signal air booster unit - 2 nos. for each type
Tender For supply of desert cooler submersible pump max power 20 watt,single phase 230v/ac water lifting 1.8 meter ,detachable and cleanable similar to khiatan zolta 60 or equivalent preferred make-khiatan , elove,axmon or equivalent reputed make note : this item is not available on gem portal. proof attached as non availability.
Tender For supply of pump for dts machine. equivalent to plasser part no. hy704x90l ep/a175(imp), rexroth pa rt no. a4vg90ep4dt1/32lnzf02 f001sp (imp), part make: plasser/rexroth, hsn- 8413, note: material supplied by firm should be fitted on machine without any modifications and all ports & mounting should m atch as per existing part on machine and all function of item should work successfully. [ warranty perio d: 18 months after the date of delivery ]