Tender For supply of ff8301700823 coupling pin bush part no 142 , ff8301700831 impeller part no 02 , ff8301700858 top shaft part no 84 , ff8301700866 line shaft bottom part no 20a , ff8301700874 line shaft part no 20 , ff8301700882 line shaft coupling part no 82 , ff8301700890 spider bush model svt 275 33a , ff8301700904 split ring set part no 78 , ff8301700912 rubber bush teper pipe part no 77a , ff8301700920 rubber bush diffuser part no 77 , ff8301700947 guard ring part no 75 , ff8301700955 internal circlip part no 51 , ff8301700963 taper pipe bush part no 21b , ff8301700971 bronze bush for diffuser part no 21a , ff8301700980 suction bush part no 21 , ff8301700998 wear ring part no 16 , ff8132040465 bearing housing with internals part no 33 and 86 m , ff8301701048 centre ring part no 16a , ff8301701056 casing wearing ring part no 16 , ff8301701064 sleeve nut nde part no 13a , ff8301701099 split gland part no 8 , ff8301701102 lantern ring part no 7 , ff8301701110 sleeve part no 6 , ff8301700840 pump shaft part no 10 , ff8301701021 horizontal pump impeller part no 02a , ff8301701030 horizontal pump impeller part no 2 , ff8301701080 shaft part no 10
Tender For tn-mm-2021 supply of spares for boiler feed pumps type fk6d30 , booster pumps type fa1b56 and condensate extraction pump type en8h32 of unit no.1 to 6 of stps, suratgarh - condensate extraction pump (pump type en8h32), cep complete assembly (type-en8h32) (without canister, head stool, motor & connecting coupling), sleeve bearing set (1set=9 nos), restriction bush set (1set=9 nos), baffle plate set ( 1 set=7 nos), grub screw ss- m 6x6 long ( 1 set=18 nos), grub screw ss- m 4x6 long ( 1 set=18 nos), wear ring set ( 1 set = 16 nos), lock washer (1 set=4 nos), lock nut ( 1 set= 3 nos), all stud & nut for cep assembly, oil level indicator, orifice stuffing box inlet & outlet hose pipe (size dia 1/2 inch & length 1.5 feet pr. 100 kg/cm2) with fitting, flexible, spacer coupling (pin & bush type) (fbc 6 ) (pump bore dia 47 mm & motor bore dia 100 mm), pin & bush for coupling (fbc 6 ) ( 1 set =8 nos), stuffing box bush, shaft tube o ring (1 set =2 nos), shaft tube, boiler feed pump (pump type fk6d30), split floating oil seal, lp cover studs (1 set=24 nos), lp cover ptfe (teflon) gasket, booster pump (pump type fa1b56), rotating assembly of bp (including of shaft impeller and required key), floating seal
Tender For tender for supply of pulley vaccum pump , cotter pin , clamp for oil bag small , o ring (27.5x3) , circlip , o ring , fuel filter , wearing ring , gasket , bonnet , o ring 1 , o ring 2 , mechanical seal upper , mechanical seal , trimming spacer , contactor , impeller (50hz) , engine gasket set , o ring(32.5 x 3) , o ring 3 , o ring 4 , diffuser , impeller , qsv spindle housing , piston with ring , 40tph starter , lower bearing , rubberised suction hose reinforced with steel spiral of 3 id , 20 tph starter , fuel strainer with o ring , impeller (60hz) , o ring (51.5x3) , o ring (77.5 x 3) , o ring (154.3x5.7) , o ring(252.5 x 3) , shaft sleeve , 3 inches gm suc.strainer with screwed coupling to suit sucti , fuel oil filter , fuel filter , o ring(8 x2.4) , o ring(164.5x3) , outer casing , circlip 2 , spring washer , fuel injector , engine gasket set , o ring(36 x3) , outer casing 1
Tender For tn-mm-2021 supply of spares for boiler feed pumps type fk6d30 , booster pumps type fa1b56 and condensate extraction pump type en8h32 of unit no.1 to 6 of stps, suratgarh - cep complete assembly (type-en8h32) , (without canister, head stool, motor & connecting coupling) , sleeve bearing set (1set=9 nos) , restriction bush set (1set=9 nos) , baffle plate set (1 set=7 nos) , grub screw ss-m 6x6 long (1 set=18 nos) , grub screw ss-m 4x6 long (1 set=18 nos) , wear ring set (1 set = 16 nos) , lock washer (1 set=4 nos) , lock nut (1 set= 3 nos) , all stud & nut for cep assembly , oil level indicator , orifice stuffing box inlet & outlet hose pipe (size dia 1/2 inch & length 1.5 feet pr. 100 kg/cm2) with fitting , flexible, spacer coupling (pin & bush type) (fbc 6) (pump bore dia 47 mm & motor bore dia 100 mm) , pin & bush for coupling (fbc6) (1 set =8 nos) , stuffing box bush , shaft tube o ring (1 set =2 nos) , shaft tube , split floating oil seal , lp cover studs (1 set=24 nos) , lp cover ptfe (teflon) gasket , rotating assembly of bp (including of shaft impeller and required key) , floating seal
Tender For supply of m/s kirloskar brothers ltd. make centrifugal pump, model kpd125-45 with trimmed impeller , enclosed impeller of m/skirloskar bros ltd. make centrifugal pump, model kpd125-45 (trimmed outside di , pump shaft of m/s kirloskar brothers ltd. make centrifugal pump, model kpd 125-45 , casing wear ring set of m/s kirloskar brothers ltd. make centrifugal pump, model kpd 125-45 , impeller wear ring set of m/s kirloskar brothers ltd. make centrifugal pump, model kpd 125-45
Tender For supply and installation of necessary equipment for updating the fire and safety system installed in regional office, chandigarh - diesel engine driven main fire pump supplying, installation, testing and commissioning of diesel engine driven main fire pump suitable for automatic operation and consisting of following, complete in all respects, as required : (diesel driven pump) horizontal type, multistage, centrifugal pump of cast of iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to is 1520. suitable hp, 1500 rpm water cooled with radiator, diesel engine conforming to relevant is standard complete with auto starting mechanism, 12 /24 volts electric starting equipment, diesel tank, exhaust pipe extended upto 10 m outside pump house duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, residential silencer, instruments and protection as per standard specification, stop solenoid for auto stop in the event of fault with audio indications, painted with post office red colour etc. as required. m.s fabricated, common base plate, coupling, coupling guard, foundation bolts etc. as required. suitable cement concrete foundation duly plastered and with anti vibration pads.(for 1620 lpm at 56 m head) note- the head of the pump is selected in a manner so as to give a minimum 3.5 kgf/cm2 pressure at the highest farthest point., control panelfabrication, supply, installation testing & commissioning of electrical control panel of cubical construction, floor mounted type, fabricated out of 2mm thick crca sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, inter connection with suitable size copper conductor cable/solid copper strip, having switchgears and accessories, mountings and internal wiring, earth terminals, numbering etc. complete in all respect, suitable for main fire pump, pressurisation pump & diesel pump set complete as per cpwd specification with following in coming and outgoings, suitable for operation on 415v, 3 phase, 50hz ac supply with enclosure protection class ip 42 as required :incoming250a, 50ka 4 pole mccb, ics=100% icu rating ,digital voltmeter 0-500v with selector switch digital ammeter (0-250 a) with selector switch & cts etc. led type ryb phase indicating lamps, on, off, trip indicating lamps, set of copper bus bar 300a.outgoing( note : all outgoing feeders for pumps should have digital ammeter with selector switches, and led type on, off, trip indicating lamps)main fire pump125 a, 50ka tpn mccb, ics=100% icu, with fully automatic star/delta starter suitable for 60 hp pump with overload protection, current sensing type single phase preventer complete with all accessories and internal wiring required for automatic operation, selector switch for local/remote, auto/manual/off operation.jockey pump63 a, 50ka tpn mccb, ics=100% icu, with suitable hp fully automatic star/delta starter with overload protection, current sensing type single phase preventer complete with all accessories and internal wiring required for automatic operation, selector switch for local/remote, auto/manual/off operation.diesel engine controlcontrol for diesel engine comprising -automatic/manual selector switch & 3 attempts starting device, timers and relays as required, push buttons, start/stop in manual mode indicating lamp for high/ low lub. oil pressure, high water temp and engine on indication, battery charger suitable for 12v/24 v dc with boost and trickle selector switch, 0-30 v dc volt meter, and 0- 20 a dc ammeter. all standard relays and accessories for automatic operation of diesel enginesystem controllerdesigning, supply, installation, testing and commissioning of system controller to control operation of main electric fire pump, diesel pump, pressurization pump, terrace pump in sequence as per specification consisting of relays, timers. sensors, annunciat
Tender For supply of spares for kirloskar make pumps at isps casing upper and lower half part no staba , impeller part no 15900 , pump shaft part no 18000 , casing ring part no 19000 , shoulder ring part no 19900 , gland part no 22300 , lantern ring part no 22700 , liquid deflector part no 23600 , bearing housing de mod part no 24001 , bearing housing nde part no 24002 , set bearings part no subsob01 , shaft sleeve de nde part no 31000 , lock nut part no 33600 , lock washer part no 41500 , vent valve 3by8 inch bsp part no 45000 , set of oil seals part no subsoo51 , flex hose pipe with quick 1by4 inch bsp part no 56000 , cylindrical pin part no 61000 , insert 200 dia de part no 97901 , insert 200 dia nde part no 97901 , set of gland packing part no subsog01 , set of keys part no subsok1 , set of o rings part no subsoor1 , set of gaskets part no subsog1 , set of fasteners part no ssof1 , pump casing part no 10500 , impeller enclosed part no 15100 , pump shaft part no 18002 , casing ring suction side part no 19000 , impeller ring suction side part no 19200 , casing cover part no 22000 , split lantern ring part no 22700 , split gland part no 22900 , bearing housing std part no 24000 , lantern bucket part no 24800 , bearing cover de part no 27000 , shaft sleeve part no 31100 , bearing lock nut part no 33600 , stuffing box bush part no 35000 , constant level oiler part no 44300 , oil breather part no 44400 , helicoil lock insert part no 46900 , internal circlip part no 48500 , impeller nut with helcoil insert part no subinhos001 , set of gland packing part no subsgp1s001 , set of bearings part no subsob2s001 , set of fastners part no subsof1s001 , set of gaskets part no subsog1s001 , set of keys part no subsok1s001 , set of oil seals part no subsooss001 , set of o- rings part no subsor1s001 , spares coupling for pump rrl 110by100 part no , spare spider for coupling part no , impeller part no 15100 , bearing housing part no 24001 , set of bearings part no subsob01 , shaft sleeve part no 31100 , set of keys part no subsok01 , double chmf hex nut part no 33000 , lock washer part no 41000 , set of gland packing part no 43001 , external circlip part no 48600 , o-ring part no 52500 , set of gaskets part no 51101 , set of fastners part no subsof
Tender For supply of spare impeller made of cast steel-is-1030fitted with ss 316 shaft, details as per technical specification , casing cover made of cast steel-is-1030, details as per technical specification , control plate made of cast steel-is-1030, details as per technical specification , mechanical seal, details as per technical specification , shaft sleeve, details as per technical specification , bearing bracket, details as per technical specification , set of gasket, details as per technical specification