Latest arm bolt Tenders | Government arm bolt Tenders

State Government

CTN :43467490

13 Jan, 2026 NA

Delhi - Delhi

Tender For s/i/t/c of e/m equipments and allied works for newly re-bored tube well at okhla vihar near majar in okhla constituency ac-54. - supply of submersible pump set fitted with dynamically balanced ss impeller mounted on stainless steel shaft with protection sleeve having stage bowl & closed grained shorted type impeller, the pump will be directly coupled to required wet type induction motor of 7.5 hp, 15 stage, speed 2900 rpm suitable for operation of 3 phase, 415 volt, 50 hz, ac supply with efficiency 70% at following duty point: 200-125-75 lpm on 89-124-133 mtr. head.having discharge outlet 50 mm and outside dia 142 mm.make: bs/skope/ any djb approved. , supply of hut type electrical feeder pillar / fabricated with 50 x 50 x 6mm angle iron and 16 swg ms sheet with horizontal and vertical intermediate member of suitable size. i.e. 1370 mm x 760mm x 460 mm. with arrangement for mounting of switchgear and electrical energy meter i.c. painting heaving following item fitted. a) mccb 63 amp, 4pole, 415volt, 35 ka -1 no. b) rccb 63 amp, 4pole with earth fault indication protecting a circuit automatically in the event of earth leakage sensitivity 100ma, - 1 no c) fully automatic star delta starter of relay range 13-21 amp. (7.5 hp to 10 hp) 3 phase oil immersed type -1 no.d) ampere 96 x 96 mm. square shape 0-30 amp-1 no. e) voltmeter 96 x 96 mm. square shape 0-500 volt-1 no.e) indicating lamp (a set of 3 lamps) 1.setf) shunt capacitor of 10 kvar mpp type with three phase isolator with suitable banking g) motor protection assembly with earth leakage protection phase sequence corrector, single phasing, protection, overload protection, high voltage / low voltage protection time delay power on, programmable time switch i.c. r&b phase facility to change over from automatic, to manual &vice verse for up to 10 h.p -01 nos.complete wiring &installation of above accessories with required copper conductor wire and thimble etc. 01 job.make of all components: any djb approved., s/o pvc insulated and pvc sheathed cable with plain copper conductor having 3 phases, 3 core flat for submersible motor of 4 square mm size each 100 mtrs. make:grandlay / havells./any djb approved make, s/o m.s. clamp of 600 mm length duly fabricated out of 12.5 mm thick 75 mm wide, m.s. plate for holding the pipe of 50 mm dia., s/o double flange gi column pipe 50 mm dia medium class each of 3 mtrs long duly threaded on both ends, welded fitted with gi flange on both ends with slot of submersible cable. make: tata/ jindal./any djb approved make, s/o/ tail piece of the medium class gi pipe 500 mm long with one end threaded as per outlet of pump & another end flanged as per size of gi pipe 50 mm dia., s/o gi 90 bend of size 50 mm dia having both side flange (heavy duty)., supply of ms nut bolts off size as per requirement., s/o rubber packing for 50 mm dia flange., fabrication and supply supply of bore cover approx size 1x1 made out from 6mm thick m.s. sheet in 2 halves and a circular hole in centre 3-1/2 dia. with locking arrangement by nuts and bolt. , earthing with g.i. earth pipe 4.5 meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required., providing and fixing 6 swg dia g.i. wire on surface or in recess for loop earthing as required., installation of t/well by lowering of sub p/set with all allied above items. this includes installation and grouting of panel boards with all electrical wiring & cabling at site. all tools & tackles i/c. tripod chain pulley blocks etc. shall be arranged by the firm. this includes testing & commissioning of t/well on load at site i/c. cartage, loading & unloading of material. it also includes a trial run of 30 hrs operation successfully by the firm. all required civil work included in the scope of work.

CTN :43502053

04 Feb, 2026 NA

Ernakulam - Kerala

Tender For tender for supply of screw bolt , nut , pin with tap hold , cap screw , lock washer , sleeve spring , piston pin bush , plate clamping , ring buna round , nut , nut castle , gasket , gasket 4d12667 , gasket 4d12668 , gasket 4d12669 , nut , piece clamping , screw , pin threaded , roller for control lever , hexagon bolt , bush , washer lock , thrust plate , valve cone with intermediate plate(fitted) , gasket , locking ring , coupling sleeve , disc , nozzle with orifices , gasket , bushing , seal ring , gasket , simmer ring , slide ring joint , key fitting air , pin threaded with joint , thermocouple temp sensor , gasket oval , ermeto bulk head screw , screw connection angular , screw connection angular , bulk head screw connection , screw

CTN :43475418

15 Jan, 2026 4.50 Lacs

Bundi - Rajasthan

Tender For supply and fixing work of open gym item in ward no 2 lakheri - part " a " :- building work ;, air swing: providing, designing and fixing of air swing in pair of size 1150 x 900 x 1250mm fabricated with main post of 114mm dia and 2.5mm thick and rest of the pipe 40mm dia and 2.5mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized and powder coated using akzo nobel or equivalent of 80 - 120 micron thick. all joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. zinc primer paint to be applied at all welding points prior to finishing. pedals shall be made of nylon alloy with rounded edges to prevent any impact of injury and base plate cover to be made from virgin lldpe manufactured by rotational moulding with minimum thickness of plastic of 3mm, colorful and uv resistant and environmental friendly. bearing used shall be maintenance free, duly oil sealed and self lubricated made by reputed company to be approved by engineer in charge. equipment to be fitted with inbuilt limiters to prevent unwanted movements. all open ends of pipe to be closed by gi/ lldpe caps for user safety. the equipment to be fixed on ground with concrete of minimum strength m-25 and j shape welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate. all complete as per direction and approval of engineer-in-charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipments etc (the cement concrete and excavation work shall be paid separately)., horse rider station: providing, designing and fixing of horse rider station of size 1000 x 600 x 1100 mm fabricated with main post of 114mm dia and 2.5mm thick and rest of the pipe 40mm dia and 2.5mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized and powder coated using akzo nobel or equivalent of 80 - 120 micron thick. all joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. zinc primer paint to be applied at all welding points prior to finishing. pedals shall be made up of nylon alloy with rounded edges to prevent any impact of injury. base plate cover and seat to be made up from virgin lldpe manufactured by rotational moulding with minimum thickness of plastic as 3mm, colorful and uv resistant and environmental friendly. bearing used shall be maintenance free, duly oil sealed and self lubricated made by reputed company to be approved by engineer in charge. equipment to be fitted with inbuilt limiters to prevent unwanted movement. all open ends of pipe to be closed by gi/ lldpe caps for user safety. the equipment to be fixed on ground with concrete of minimum strength m-25 and j shape welded bolt and once the concrete is set, fix the equipment on to it and cover with the base plate. all complete as per direction and approval of engineer-in-charge regarding material, shape of equipment, colour on metal, seat and base cover plate cover and fixing of equipments etc (the cement concrete and excavation work shall be paid separately)., stair stepper: providing, designing and fixing of stair stepper in a combination of pair and a single step of size 1000 x 800 x 1400 mm fabricated with main post of 114mm dia and 2.5mm thick and rest of the pipe 40mm dia and 2.5mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized and powder coated using akzo nobel or equivalent of 80 - 120 micron thick. all joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. zinc primer paint to be applied at all welding points prior to finishing. pedals shall be made up of nylon alloy with rounded edges to prevent any impact of injury and base plate cover to be made up from virgin lldpe manufactured by rotational moulding with minimum thickness of plastic as 3mm, colorful and uv re

CTN :43456217

12 Jan, 2026 5.87 Crore

Baran - Rajasthan

Tender For procurement of turbine spares for ctpp units - coupling bolt m56 hp-ip , clamping piece 7th stage , clamping piece 8th stage , locking plate 7th stage , locking plate 8th stage , hose dn 6x2500 , hose dn16x2200 , hose dn16x1200 , cylindrical pin d16x31.5 , helical compression spring , sealing ring (in 8 parts) , sealing ring (in 6 parts) , sealing ring (in 6 parts) , sealing ring , sealing ring , screw hexam24x90 , u-sealing ring (machine as per drg.) , disc , disc , sealing ring (machined as per drg) , u-sealing ring (machined as per drg) , stud boltl-945 , stud bolt=895 , stud bolt=830 , stud bolt=730 , stud bolt=595 , screw hexam30x115 , screw hex.am20x37 , sealing ring assembly (8 segment) , sealing ring assembly (6 part) , sealing ring assembly (6 part) , moving blade lp3r , moving blade lp3l , key , sealing ring (6 part) , sealing ring (6 part) , disc , spacer (hw-114.58) , spacer (hw-114.14) , spacer (axial key) , fitted key , fitted key , gasket was.01 , 1.1315e+13 , gasket was.04 , 1.13151e+13 , stud m24 x200 11315131000007 , gasket con:qn:0162014 (crh nrv) , sealing ringb50x70 (thick-ness 5 mm) , sealing ringa50x70 (thick-ness 10mm) , sealing ring180x200x10 , valve spindle , fitted key(thickness shoul be 9 mm) , screw hexam24x50 , angle ring(mcd as per drawing) , stud b m64x305-20x263 , seal strip 8x2,l-1100 , studm42fox150ri , studm42x195 , cap nutm42 , studm36x150 , cap nutam 36 , cyl. pin as per drg. no. st05001, size no.145

CTN :43166123

13 Jan, 2026 NA

Ernakulam - Kerala

Tender For corrigendum : procurement of gear box spares - gear box spares, pressure gauge, filter element, pressure valve, valve non return rhu 25 sr bar, casing nut, pin threaded with stud, ring sealing shaft 230 x 260 x115, cylindrical bolt with spring ring a, cyl bolt m 30b x 110, din 912, cylindrical bolt b, antifriction bearing, anti friction bearing qj234, anti friction bearing nu 1044, anti friction bearing nu 22319 c, shaft sealing ring 115x114x13, coil distributor e28, wheel a, wheel b, threaded pin a, cylindrical bolt c, pin tapered, ring nut, locking pin, hexagon bolt with spring washer a, anti friction bearing nu 22320c, bush a, hexagon bolt with spring ring a, anti friction bearing a, bush c, hexagon bolt with spring ring b, locking plate a, hexagon bolt with spring washer c, ring sealing shaft 340 x 380 x 20, ring, spring a, locking plate b, threaded pin with nut, pin gapered with nut, clutch support, valve non return r 1/2" v-4-20 6919, spring washer c, piston annular, ring piston 470 x 437 , 4 x 10, ring locking a, disc inner 3-002-340-78-151, disc outer 3-100-210-78-78-005, pin carrier, carrier 4.223 20868/01, bolt cylindrical, clamping sleeve, plug screw, spring washer d, screw cyl m 16 x 120 din 912, spring sk 4.20.7207, hexagon screw w, anti friction bearing 22326c, bush 340x 300 x 92, anti friction bearing, anti friction bearing 29352, bush b, threaded pin b, cylindrical bolt with spring ring d, circlip, key fitteda, cylindrical bolt d, shaft nut, hexagon screw x, anti friction bearing qj243, bearing anti friction, anti friction bearing nu 236e, ring locking, clamp ring, control valve, valve slide, spring, threaded pin c, fitted key, fitted key 32x18x110, bush, fitted key b, threaded pin d, nut shaft, locking bolt, key fitted d, threaded pin e, fitted key c, bush 230 x 200 x 83, cylindrical bolt f, key fitted e, cylindrical bolt with fspring ring g, threaded pin f, bush 1

CTN :43452174

02 Feb, 2026 NA

Ernakulam - Kerala

Tender For tender for supply of bolt for crank shaft bearing cylinder , nut , gasket m618 23x33 cu , thrust bolt , nut castle , pin cotter , cylinder pin , crankshaft bearing shell complete , cotter pin , cap screw , sleeve spring , pin cotter connecting rod cotter pins din 94 8 70 , cotter pin , piston pin bush , screw plug , ring piston rpointh cap , piston ring with lh cap , clamping plate , pin locking , ring sealing , seal ring cu , seal ring cu , nut , stud , nut castle , pin cotter , ring spacing , seal for cyl head , stud , nut , seal for cooling water passage , screw hex head , bolt , seal , seal for cooling water passage , strip sealing , lock washer , bolt , gasket , seal 4d12770 , seal 4d 12773 , gasket long & seal , gasket long seal , buna ring , seal gasket , cotter pin , gasket , seal , seal , taper pin , bolt fitted , washer lock , bearing shell half , nut , screw , worm screw , taper pin , hexagon nut , taper pin , seal designs a b c dpoint , pin cotter , spacing ring , taper pin , seal , seal , screw , pin dowel , pin taper , lever control outlet , spherical seat , ring locking , bolt , piece ball , locking ring , cup type seat , seal 5d 14104 , cowl , roller and bolt , sleeve hose , cone for inlet valve , screw hex head with pin , washer lock , valve guide , piece clamping , spring washer , screw , thrust plate , ring snap , valve guide , fitting key , socket head screw , piston , thrust spring , bush , ring round , thrust spring , piston , gasket , starting valve complt , screw vent , spring thrust , stud , nut hex , sealing ring , gasket , shim set , gasket , pin cotter , forked end , taper pin , pin taper , cotter pin , pin taper , pin taper , pin collar , bush for gear wheel , bush pump roller , gasket , locking ring , seal ring , gear wheel , spring for cooled fuel needle , ring snap , nozzle with orifice , nozzle with orifice , round seal , gasket , bolt hex , seal , bolt collar , suction sieve , gasket , gasket , screw hex head for exhaust piping , gasket , gasket , gasket , key , hex head screw , positioner govpointcont assy , deep groove ball brg , shaft , ring slide seal 40 , butting ring suction stage , rubber ball , gasket seal , bearing cover , nut for rotating wheel , pump shaft seal side ring seal 40x61 130 , slide ring seal coal , butting ring pos 15 , slide ring seal pos 34 , cord seal pos 52 , key 10x8x40 , seeger ring pos 113 , simmer ring pos 114 , link elastic for tachometer drive , gauge charging air pressure 0 to 1 kg , gauge pressure luboil , thermocouple temp sensor , gasket , ring sealing m618 14x21x3cu , ring sealing for indicator cock , indicator valve , sealing ring , coller screw , sealing ring , indicator valve , gasket for start air distributor , screw connection ermeto for piping , screw connection straight , screw connection straight , ermeto screw connect , union , screw connection angular , screw connection angular , bulk head screw connection , seal for cpointw outlet , seal gasket , cock r55 f6xr3 8cu , fuel shut off cock , o ring , ring loop 21x3 , loop ring , thermometer 0 to 100 c , o ring

corporations/Associations/Others

CTN :42941512

12 Jan, 2026 NA

Anpara - Uttar Pradesh

Tender For corrigendum : supply of misc items for ffsd-i & ahd btps anpara - ht hex head full thread nut & bolt ; m16x65 mm,, ht hex head full thread nut & bolt ; m16x70 mm,, hthh bolt with nut & washer , half threaded m16x90, hex hd m18x70; ht 10.9 grade, ms bolt & nut size 20x70 mm, ht hex bolt & nut 20x80fth, fluidizing pads for esp hoppers, size: 374 mm x 374 mm, no. of holes: 16, hole dia: 12 mm material: nomex (as per sample), perforated ms plate, size: 374 mm x 374 mm, having 4.76 mm dia holes at 7.14 mm pitch giving 40.5 % open area plate thickness: 1.6mm, no. of mounting holes: 16, hole dia: 12 mm (as per sample), submersible pump, make-kirloskar, model-eterna 1100 cw+ specification : power supply-415v, 3phaseacpower rating-1.1kw/1.5hpmax. solid handling size (mm) - 24minimum submergence (mm) - 460suction - from bottomsize discharge outlet (mm) - 50max. amb. temperature - 40 degree cdischarge 366 to 84 lpmtotal head - 6 to 14 mtrsspeed (nominal) 2800 rpm, discharge tube with fmb(foam making branch) for mechanical foam extinguisher 50 ltr. discharge tube shall be braided rubber plasticof 3.5 mtr length & 12.5 mm internal dia. fitted with plastic fmb (is-7328) as per is-13386 the discharge hose shall have bu stingpressure of not less than 50 kg/cm . (as per sample), discharge tube for dcp(dry chemical powder) 05 kg extinguisher (plunger type). made of pvc. one end thread is provided to fit withdcp fire extinguisher (plunger type) capacity 5 kg and other end to discharge powder.(as per sample), discharge tube washer for dcp(dry chemical powder) 05 kg extinguisher (plunger type). made of rubber suitable to be fitted withdischarge tube of dcp fire extinguisher (plunger type) capacity 05 kg.(as per sample), discharge tube for dcp(dry chemical powder) 10 kg extinguisher (plunger type). made of pvc. one end thread is provided to fit withdcp fire extinguisher (plunger type) capacity 10 kg and other end to discharge powder.(as per sample), discharge tube washer for dcp(dry chemical powder) 10 kg extinguisher (plunger type). made of rubber suitable to be fitted withdischarge tube of dcp fire extinguisher (plunger type) capacity 10 kg.(as per sample), cap rubber washer for dcp(dry chemical powder) 75 kg extinguishers.made of rubber, suitable to fit in the cap assembly of dcpfire extinguisher capacity 75 kg.(as per sample), discharge tube for dcp 75 kg extinguishers. discharge tube/hose with nozzle squeeze grip aluminum lengths -5 mtr. suitable fordcp type fire extinguisher capacity-75 kg.(as per sample), washer for copper connecting tube 75kg dcp(dry chemical powder) extinguisher. made of rubber. suitable for fitting with copperconne cting tube of dcp 75 kg extinguisher.(as per sample), discharge tube for 9 ltr water type extinguishers (squeeze grip type). pvc braided tube/hose of length 400 mm. suitable for fittingwithin the thread of squeeze grip assembly of water type fire extinguisher capacity 9 litre (squeeze grip type).(as per sample), discharge tube washer for 9 ltr water type extinguishers (squeeze type). made of rubber. suitable to be fitted with discharge tube/hoseof water type fire extinguisher (squeeze grip type) capacity 09 litre.(as per sample), port tube for 9 ltr water type extinguishers (squeeze grip type). port tube/actuator should be made of aluminium. suitable to fit insidecap assembly of water type fire extinguisher capacity 9 litre (squeeze grip type) for release of water when activated. as per sample), siphon tube for 9 ltr water type extinguishers (squeeze grip type). siphon tube suitable for 9 ltr. water type extinguishers (squeezegrip type).(as per sample), cap assembly for 9ltr water type extinguishers (squeeze grip type). it should include a brass forged valve and a squeeze grip foractivation to facilitate the discharge of water. suitable to be fitted in 9l water type extinguishers (squeeze grip type).(as per sample), cap assembly washer for for 9 ltr water type extinguishers (squeeze

CTN :43369500

19 Jan, 2026 NA

Mumbai - Maharashtra

Tender For tender for supply of stud bolts high tensile steel round bsf thread for high temp , bolt and nut ms galvd unc 2a hex head plated thread 1 2 4 1 , screw steel 5 16 1 2 , stud bolt 5 8 4 1 2 1 1 4 unc thread cl za gen purposes , nut butter fly 7 8 bsw , nut butter fly 7 8 bsw , clip butterfly tapped 1 2 gun metal for hatch covers , rivet pop aluminiumalloy tap d 529 b s , rivet copper 10 g 3 8 , nut h t brass 1 2 , nut h t brass 3 4 , hasp and strapple 6 , hinges steel cross garnet 12 , washer copper 5 8 7 8 5 16 , washer copper , washer copper 3 8 11 16 , nail steel 50mm , pad lock 7 levers , screw brass for wood csk hd 7 8 10g , screw brass for csk hd 2 18g , screw brass 2 22g , screw brass csk hd 5 30g , screw brass for wood csk head 2 1 4 10g , screw brass for wood round heads 2 1 4 14g , screw brass wt round hd thread 1 4 3 8 , screw brass csk hd 1 3 8 7 16 , nut brass hexagonal for 1 b a screws , nut brass hex 5ba , nut brass 0 172 094 7ba plain hexagon , ms spring washer 14mm id 15 0 od 20mm thk 2 5mm , moulder rubber lip picgs , mount resilient , busing rubber 1 unit type k 180 360 kgs soft , bush soft , brush wire , screw brass 1 10g csk head for wood , s s screw , bolts steel hex hd 3 8 bsf 3 , bolt steel bsf 3 8 4 , bolt 5 8 115mm , bolt steel screwed hex hd fitted with nut 5 16 4 , bolt bsw black steel hex hd ftd with nut 5 16 5 long , bolt bsw black steel hexagon head unmachined with hex nut f , bolt steel screwed hex hd with nut 3 4 2 3 4 , bolt steel screwed hex hd with nut 3 4 4 1 2 , bolt steel 1 2 3 1 2 , bolt 1 2 2 1 2 1 1 4 , bolts black steel hex hd m18 90mm with nut , bolt with nut 20 120mm , ms bolt and nut 24 110mm , bolt nb hex w o nut 3 4 2 1 2 llength screwed 1 3 4 , bolt hex hd naval brass 1 bsw 3 long , bolt machine hex brass course pitch ni chro plated 6 25mm , stud metric 8 8 type b m 12 110mm long , high tensile steel stud metric threading dia 20mm len 41.5mm , nut brass 5 8 , nut brass 3 4 bsw thickness 687 plain hex full bearing , bolt brass nut nb for bolt 7 8 thrd 0 875 ht 0 750 19mm , nut hex 16mm , nut plain hexagon , nail steel clout contersunk hd chisel point strong 65 7mm , hasp staple steel 125mm , hing brass butt 25 mm , hinge brass 4 , padlock 4 lever iron 65mm , padlock galvanised iron 65mm , resilient mounting , colt carborundum 150 grade emery clot size 230mm 280mm , pin drop n b for guard stanchons stay , screw brass 1 1 2 16g csk head for wood , bushing rubber 2 unit type k 180 360 kgs soft , bolt bsf precision r steel hex hd zinc plated 5 16 1 l , hinges brass double action spring 100 mm , galvanometer iron padlock 75mm , stainless steel nut 20 2 5 mm

CTN :43369708

19 Jan, 2026 NA

Pune - Maharashtra

Tender For supply of wc indian type for toilet bathroom under job no 0119 oblique 25-26 mta , flash tank for toilet bathroom , switch bd 8 inch x 10 inch for toilet bathroom , pvc square box for living shelter , switch bd 10 inch x 12 inch for living shelter , switch 5 amp for living shelter , curtain rod for living shelter , curtain rod bracket for living shelter , cloth hanger for living shelter , sliding bolt for living shelter , tower bolt for living shelter , hdpe sheet storage sheet 10 x 10m for 50 kl water tank , ss stop cock t type for fd toilet , pendent holder for fd toilet , switch piano 5 amp for fd toilet , led bulb 9w for fd toilet , exhaust fan 300mm for storage shelter , tube light 4 feet long fitted for storage shelter , ceiling rose for storage shelter , ceiling fan 1200mm for storage shelter , battery box for route marking store , torch for route marking store , nylon rope 6mm for route marking store , gi union 50mm for jerrican filling device , pipe wrench 2.5 inch for jerrican filling device , pipe wrench 1 inch for jerrican filling device , sintex water tank 1500 ltrs for jerrican filling device , urinal pot for relocatable fd toilet , wash hand basin for relocatable fd toilet , urinal pot for mob fd toilet , wash hand basin for mob fd toilet , fuel filter for genr set 15 kva , oil filter for genr set 15 kva , fan belt for genr set 15 kva ) /bid number : gem/2025/b/7050687 * /dated: 29-12-2025 & & / bid document 1 / 29

Arm Bolt Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

State Government

corporations/Associations/Others