Tender For supply of civil engineering laboratory equipment - prismatic compass , cross staff , optical square , dumpy level with all standard accessories , transit vernier theodolite , tilting level , plain table with standard accessories , orifice meter , apparatus for determination of coefficient of discharge contraction and velocity through an orifice , simple jib crane apparatus , simply supported beam apparatus , winch crab single purchase apparatus , friction slide apparatus , screw jack , le chatelier apparatus , vibrating table , vicat apparatus , cube moulds , standard sieve set for coarse aggregate , flakiness sieve set , standard set of sieve for fine aggregate , unconfined compression test machine , vane shear test motorised , modified proctor test apparatus , infra red moisture meter , liquid limit apparatus , sand replacement test apparatus , standard proctor test apparatus , los angeles abrasion testing , ductility test of bitumen apparatus , aggregate impact tester with blow counter , california bearing ration test , crushing value apparatus , standard penetration test , rebound hammer tester , bitumen penetrometer with automatic time controller , digital ph meter , residual chlorine meter , dissolved oxygen meter , bod analysis system , nephelometer , automatic digital conductivity meter
Tender For supply of accessories -1 spares for tilt-a-jet max jet 5i nozzle, a. maxjet 5 final filter assembly 10 nos., 10 nos, 2, spares for tilt-a-jet pull to open valve assembly ( air actuator ), a. pull to open valve kit , taj 1 nos., b. pull to open stem assembly 3 nos., c. on / off valve seat 2 nos., d. on / off valve seal assembly 5 nos., e. on/ off valve backup ring assembly 5 nos., 1 set, 3, spares for adjustable pump orifice (ass4) enduro max pump, a. 3/8 ss collar ( 60 ksi ) 10 nos., b. anti vibration type slotted collet (60 ksi ) 10 nos., c. tapered seat for adjustable dump orifice-2 nos., d. tapered stem assembly for adjustable dump orifice 2 nos., e. seal guard for adjustable dump orifice 5 nos., f. seal assembly for adjustable dump orifice - 5 nos., g. seal backup for adjustable dump 5 nos., i. erosion shield for adjustable dump orifice - 5 nos., 1 set, 4 spares for enduro max pump, a. adaptor for manifold filter 2 nos., 2 nos, 5, spares for main fold assembly, a. manifold end cap washer 15 nos., b. manifold filter assembly 3 nos., 1 set, 6, spares for check valve body, a. inlet check valve retainer nut 1 nos., b. check valve retainer 2 nos., c. 1/4 inch ceramic ball 5 nos., d. check valve seat 5 nos., 1 set, 7, spares for segand retainer, a. seal retainer - 3 nos., b. seal, dynamic 12 nos., 1 set, 8, spares for coolant housing, a. u- cup seal od 9/16 inch x id 5/16 inch x thk 1/8 inch 5, nos., b. seal reatainer sleeve 5 nos., c. internal bowed snap ring with housing id 0.562 inch ,, stainless 5 nos., 1 set, 9, spares for dual port swivel assembly, a. dynamic back up ring for dual port swivel 10 nos., 10 nos, spares for integrated on / off valve assembly, a. integrated on / off seat valve 5 nos., b. plunger screw set (ball m6x1, 14 mm long , ss) 5 nos., 10 c. acron nut (m6x1 , ss ) 5 nos., d. on/ off valve seal assembly 10 nos., e. on/ off valve stem retaining screw 5 nos., 1 set, 11 mixing tube roctec 500 with id 0.042 inch 5 nos, 12 jetlube guard synthetic grease 2 nos, 13 electric insulating dielectric grease 2 nos, 14 major rebulid kit for enduromax pump 1 nos, 15 minor rebulid kit for enduromax pump 1 nos, 16 integrated valve kit (60 ksi) 1 nos, 17 maxjet 5-i diamond nozzle assembly 1 nos, 18 the above listed spares are required for omax make water jet cutting machine (model no:, 60120)., 19 the material will be rejected if the supplied material will not be fitted for the omax make, water jet cutting machine (model no: 60120)., 20 material will be rejected if the supplied material will not be properly fix with the machine, assembly and machine will not be run as per the manufacturer recommendation., for water jet cutting machine