Get complete information related to latest Automatic Switch Tenders . from India at Classic Tenders. Search the best available tenders from Indian government tenders, domestic Automatic Switch Tenders , private tenders, online tenders, tender invitation notice, business tender notices, online tenders and bidding Automatic Switch Tenders.
Tender For supply of setting up of kidney transplant unit at aiims nagpur - air handling unit , supply of air handling unit eight hp , supply of refnet of required size , sitc of ahu connection kit. , installation of air handling units with ahu kit , installation of eight hp vrv condensing units , refnet joint , sitc of refrigerant piping for suction and liquid line , necessary refrigerant gas and oil charge , fabricated stand of ms base frame , drain piping for ahu condensation , sitc of aluminium ducting twenty two gauge , sitc of fire resistant flexible canvas sleeve flexible connections , sitc of manual fire damper with fusible link , sitc volume control damper , sitc of return air aluminium grill , sitc of laminar air flow , sitc of pressure monitoring system , sitc of pressure relief damper , sitc of uvgi lamp , sitc of medical grage copper pipe line , sitc of medical gas outlet , supply and installation of al risers , supply and application of nitril rubber insulation for internal duct , supply and application of exposed duct thermal insulation , supply and fixing of duct acoustic insulation . , removing of existing fire sprinkler smoke detector etc , supply and fixing of abc six kg extinguisher , supply and fixing of co2 four ponit five kg extinguisher , supply and fixing emergency evaccuation plan , supply and laying fire frls armoured cable , sitc of electrical panel , sitc of ahu control unit , sitc of vfd for ahu motor , sitc of heater bank , supply and laying of electrical power cabling copper armourred , supply and laying of electrical wire and conduit , supply and laying of ms conduit , supply and laying of pvc conduit , supply and laying of earthing strip with accessories , supply and laying of eight swg earthing wire , supply laying and termination of xlpe aluminium armored cable , supplying and laying of gi perforated cable trays , supply and laying of raceway , supply and fixing of switch socket as per the specifiaction , providing and laying cat six pair cable with all necessary accessories , supply and fixing of four way tpn horizontal db box with all accessories , supply and fixing ofisolator , supply and fixing of rccb , supply and fixing of mcb , supply and fixing of isolator , providing and fixing of scaffolding , sitc of bed head panel , sitc of ups as per specification , sitc of clean room luminaries , wall panel system , ceiling panel system , providing and fixing ante static vinyl flooring , providing corner coving , dismantling aluminium or gypsum partitions doors windows etc , providing ms cabinets including handles and accessories , providing and fixing tower bolt , providing sliding door , providing and fixing aluminium work polyester powder coated aluminium , providing and fixing aluminium work with float glass panes , providing and fixing double action hydraulic floor spring , providing ans fixing scrub station two bay , providing and fixing brass mortice latch and lock with levers without pair of handles , providing and fixing dgu glass in window , colour wash and applying white cement based putty fnishing with epoxy paint , providing and laying autoclaved aerated cement blocks , providing cement plaster , h type stainless steel grade stain finished pull handle of approved fixing accessories , demolishing brick work or concrete manually , extra for providing frosted glass panes instead of ordinary float glass panes in doors windows
Tender For supply of tools and equipment - ohm meter; series type& shunt type, portable, box type, magnetic flux meter, 3- point d.c. starter, 4- point d.c. starter single phase variable, auto transformer copper winding d.c. shunt generatorwith, control panel copper winding d.c. compound generator with control panel including fitted rheostat, voltmeter, ammeter, and breaker copper winding motor generator(dc to ac) s~t consisting of - shunt motor w~th, starting compensator and switch
Tender For providing of custom bid for services - 200134226 maintenance contract of ci systems and equipments for fgd area at ntpcunchahar stage4 for one year- 10) maintenance contract of c&i systems and equipments for fgd area at ntpc-unchahar stage-4. 10.10 item service code no.: cipna00gn400 desc:- removal & remounting of pneumatic actuator(diaphragm type or power cylinder type) will consists of any combination of following activities: 1. removal of pneumatic connections and required instruments like solenoid valve, limit switch, afr, positioner, pft etc from actuator and decoupling from valve after ensuring proper isolation from process side. 2. removal of actuator from its position. 3. transportation of actuator from its location to a safe place. 4. remounting the actuator after clearance from mechanical maintenance. 5. re-fixing /replacing the related accessories removed earlier as per point no-1 above and restoring pneumatic connections including cable dressing, copper tubing, tagging etc. 6. final operation checking from local & control room (fgd ddcmis system) after calibration and feedback adjustment. defect liability period: 01 week 10.20 item service code: - cipna00gn106 des:- checking/pm of pneumatic control system pneumatic actuator (diaphragm type or power cylinder type) and its mounted accessories, will consists of any combination of following activities: a) checking/pm of solenoid valves mounted on pneu. act. i. check solenoid coil physical and electrical healthiness and tightness of terminals if required ii. clean its external parts. iii. check & adjust air supply pressure as per requirement iv. check tightness checking of all parts. v. energize with correct voltage and see solenoid valve operation if required as per instruction of area in charge. vi. if solenoid valve is not working or coil resistance is not adequate replace solenoid valve or coil and check operation. vii. tighten checking of wires at terminals & at junction boxes. b) checking/pm of positioner and position feedback transmitter mounted on pneu. act. i. check & adjust supply pressure as per requirement. ii. clean its external parts of positioner and check its operation, if necessary, as per instruction of area in charge. iii. if required, connect pneumatic test signal at i/p, 0.2 kg/cm2. adjust positioner zero adjustment spring, till actuator comes to zero position. adjust 4ma o/p of pft with zero pot. iv. raise pneumatic test signal to 1.0 kg/cm2 and adjust span of positioner, till actuator reaches 100% position. adjust 20ma o/p of pft with span pot. v. repeat steps ii to iv till the required repeatability is achieved. vi. tighten terminals at junction boxes. c) removal and restoration of c&i connections as per requirement during unit shutdown or as per requirement. i. removal of accessories like solenoid valves, positioner, i/p converter, air lock relay, air filter, air filter regulator, limit switch, position feedback transmitter, volume booster, pneumatic lines, etc. ii. keeping all accessories safely at suitable location. iii. restoration of all accessories removed and connection of air lines as per original scheme. iv. checking of functioning of actuator after restoration of connection. v. calibration / adjustment of complete system if required. d) checking/pm of i/p converter/smart positioners if any i. adjust supply pressure as per requirement. ii. check ma input to i/p converter/smart positioner. iii. check i/p converter/smart positioner o/p with portable gauge. it should correspond to its characteristic, if not, remove it and send to c&i lab for calibration/repair. iv. bring i/p converter/smart positioner from c&i lab and fit it in line. v. connect ma signal and normalize the system. vi. tighten terminals at junction box. e) checking/pm of regulating type actuator operation. i. check and adjust supply air pressure as per requirement of respective actuator. ii. set demand to 0% from control room after taking p
Tender For corrigendum : supply of f22 power supply extra make - essl ip based fingerprint rfid attendance access control system , erd 12v 2amp adopter -ad-20p input voltage - 150-240v 50- 60hz stabilized output low ripple low interference short circuit overload protection , f12 - fr1200 id make - essl finger based rs485 - exit slave reader , exit switch , 4x4 pvc junction box pvc square junction box 4x4 inches , emlock 600lbs electro magnetic door lock - 600 lbs , l bracket door holding bracket - l shape bracket for emlock , z bracket door holding bracket - z shape bracket for emlock , attendance software - desktop licence subscription -subject to yearly renewal report generating software valid for 12 months , installation commisioning of biometric security lock
Tender For corrigendum : tender for supply of motor, probe, electrode, solenoid coils for lpg service, suitable for fs 10 burner, high voltage lead, distributor diffuser disc, transformer, manifold hsn code:8416, end cone hsn code:84169000, capacitor (4ufd) hsn code :8532, 7 pin plug male & female, 6 pin plug male & female, control box, pressure switch, solenoid valves, u bolt, elbow, lead, gas nozzle
Tender For corrigendum : supply of measuring steel tape , combination plier insulated , screw driver insulated , electrician screw driver thin stem insulated handle , heavy duty screw driver insulated , electrician screw driver thin stem insulated handle , punch centre , knife double bladed electrician , neon tester , steel rule , hammer cross pein , electrical symbol and accessories charts , pipe vice , hand vice , table vice , hacksaw frame with blade , file flat , file half round , file round , pliers ,long nose , pliers flat nose insulated , pliers, round nose insulated , d.e. metric spanner double ended , wire gauge imperial stainlees , portable electric drill machine , crimping tool , pliers side cutting , wire stripper adjustable length , hammer ball peen with wooden handle , scriber , tool kit box or bag portable , allen key , scissors blade , electrical load board , torque wrench , pipe cutter to cut pipes , try square , multi meter analog , load bank variable , wire cutter and stripper , earth plate , earth electrode , out side micrometer , tap and die set , trolley for transportation of batteries , rooftop mounting structure , electrical wiring and switch gear rack , protective relays and contactors rack , mccb , elcb and rccb , fuses , digital multimeter , megger , hydrometer , solar insulation meter , pyranometer , pyrheliometer , lux meter , magnetic flux meter , tong tester or clamp meter , soldering iron , temperature controlled soldering iron , thermometer digital , sun shine recorder , weather monitoring station , solar cell based sunlight radiation meter , magnetic compass , cut models of photo voltaic cell assembly , cut model of lead acid battery , lead acid battery , solar simulator for solar cell characteristic study , i v curve tester , sun path finder , solar energy trainer with grouping of solar cells , solar tracker demonstrator kit , solar pv e learning software using animations for training , halogen lamp with stand for illumination of solar panels in lab , motorized bench grinder , battery charger , solar photovoltaic module , solar panels , solar charge controller with dusk to dawn automaticswitching , solar charge controller with manual switch day lighting , array junction box , solar lantern , solar lantern assembly sets , home light system , solar cell kit , clinometer , spirit level , anemometer , dc table fan , ac voltmeter moving iron , volt meter , ammeter mc , ammeter mc centre zero , power factor meter , rheostat , ac energy meter , kilo wattmeter analog , digital wattmeter , phase sequence indicator , frequency meter , dc led lamp , dc pump , pwm controller , mppt charge controller , inverter with battery , solar pcu , solar grid tied inverter demonstrator kit , solar street light , solar wind hybrid power plant , solar traffic light , water treatment solar plant demonstrator kit , solar dc pump , demonstration kit for wind generation wind turbine with blower , working bench , wiring board