Tender For nib for supply of hardware - super senior pellet mill, bearing cover frontforged steel, bearing cover rearforged steel, bearing setting ringforged steel, counter shaft assembly with pulley without beltwithout bearing & pedestal, die cover ringforged steel, die holder (steel) forgedforged steel, die holder assemblyforged steel, die holder rind rearsuitable for above alloy steel, die holder ring frontforged steel, feeder conditioner s. s. knifes.s. 304, thread 1/2" bolt per piece, feeder conditioner screw and paddle type feeder conditioner body s.s. approx. 1430 mm long s.s. -304 construction arrangement of single drive feeding end., front bearing spacer for t shaft, front scraper (roll stay assembly)forged steel with clamping stay, front scraper blades for pellet mill, pellet cooler air lockheight 450 mm/width 250 mm inlet/outlet 155 mm, pellet cooler eccentric assembly, pellet cooler sensor, pellet diesize:520 dia inner x 635 outer x 23.0 wider pellet :10/8 mm hole perforationmounting: tapper collar 12 deg on 620.6 dia or straight plug dia 610 diafixing 12-m 20 x 25 deep on 565 pcdmaterial: en 19c or 42crmo4 duly hardened & temp. polished, rc4=5, pulley assembly (fly wheel) 11 grooveforged steel, rear scraperforged steel, roll holder shaft (t shaft) assemblyforged steel, shearing pin, helical gear with hubone set containing 2 numbers, helical gear without hubone set containing 2 numbers, pellet mill sieve, screw for variable speed feeder conditioner for pellet mill, shear pin holding body, shear pun bush, spring set, teflon bush for main t shaft, pallet down spout, roll stay support stud (ss), pedestal sn 617, pedestal sn 619, pedestal sn 615, press roll assembly super senior, bearing cover, bearing retainer/nut for eccentric shaft km- 20, center bolt/roller stud (allen, bolt, head type design), circlip(dia 180 inside), clamping device tension ring(90x101x17) mm , distance ring, eccentric shaft, lock nut with lock washer for press roll eccentric shaft, lock washer (mb-20), nut for center bolt (lighting ring), press roll assembly complete with shell, bearing etc.suitable for above en-24 shell, press roll shell, setting ring, spacer (sealing ring), molasses mixer, molasses cutting knife with nutsuitable for above ni, hard duly balanced, paddle plane and loop typesuitable for above ni, hard duly balanced, spray pipe nozzle with nipple1.5 inch c class pipe, 3/8 inch nipple, mixer pipe (ss) suitable for molasses mixer, full circle hammer mill, beater (flat type) all equal weight, (big size 180 mm x 50 mm x 10 mm)ni hard, dynamically balanced, beater (flat type) all equal weight, (small size 140 mm x 47 mm x 06 mm), beater holder shaften, material, beater holding bush (size length 30 mm, in dia 20 mm, outer dia 30 mm), beater holding bush (size length 60 mm, in dia 20 mm, outer dia 30 mm), beater holding bush (size length 36 mm, in dia 20 mm, outer dia 30 mm), beater holding bush (size length 53 mm, in dia 20 mm, outer dia 30 mm), carrying rod for hammer mill 2 no of each set, door closing clamp set, hammer mill feeder, permanent magnet, sieve set3 mm, thick ms sheet with 3 mm, 2mm, 4mm, 5mm and 6mm perforations, sieve set clamping frame, hammer mill rotor, screw conveyor, screw conveyor, gravity pipe clamping 8 inch dia., gravity pipe clamping for above pipe8 inch dia, 16 gauge., gravity pipe m.s.8 inch dia, 16 gauge, 1 meter long, gravity pipe s.s.8 inch dia. 14 guage 1 mtr. long., pazama flap 3 way for distributionsuitable for 8 inch pipe, screw of different sizes, shaft suitable for joining the screw conveyor, chain conveyor, radler chain matching our existing chain conveyor. chain should 10mm thick links along with bushes and roller duly hardened., chain supporter with single bearing $nylon roller with shaft and bearing 1 no., lock ring, shaft 255mm long, chain supporter with double bearing $nylon roller with shaft and bearing 2 no., lock ring, shaft 255mm long, chain supporter (3-piece bush) $nylon roller without beari
Tender For supply of spares for hmt praga roll threading machine : : - wedge part no 5132a08 , locking tenon for tilting block part no 5132308 , cross piece part no 5134a07 , bearing cage part no 5134a08 , bush for m22x180l part no 0859616b , cam follower cf10uur part no b21032 , work rest m22x180l part no 04182 , bearing bush for rna4919 part no 5132g05 , bearing rllr rna4919 ndl sngl 110mm 35mm part no , wiper brush part no 70403003
Tender For supply of single roll deflector idler with 219mm? tube and 40mm? bearing for 1000mm width conveyor belt, , single roll deflector idler with 219mm? tube and 40mm? bearing for 1200mm width conveyor belt,
Tender For bid to ras supply of motor , v belt , condenser , labour charge , compressor gas , coil repairing , fan blade , door rubber , gas , cylinder head , crank assembly , main bearing , filter , engine oil , packing kit , oil pump assemble , piston , ring set , cunkting pad , head valve , fuel pump , bearing and head , engine opening and fitting , presure assembly , chain set , gair oil , bearing , gear box , gear fork , gear seal , belt , leath work , labour gear box , compressor acr444 , relay , olp , capacitor , labour charge , motor repair , wiring replacement , motor copper binding , delta hmi touch screen , plc to hmi wiring , programing , frontms plate , wire , 12 inch by 20 inch glass , stripper pad , boss slide , pressure roller , cover f stripper pad , base stipper pad , frame panel , main swpcb , start key , serrvices charges , master making pcb , wire harness mm unit , sensor , plate elevator r , plate elevator f , elevator shaft assembly , elevator rack pf , alane boilt , timer puli sim , lock , bibrator seat , nylon bailt roll , rubber roller water roller ss , water roller ss , rider tray ss , rider roller ss , water vest tray , ink cleaner rubber , service charges , copper binding , brakes , 40005372 feed motor assy. , service chargess , motor binding , fan sheet , grassor honeycomb , fan blades , water pump , motor leg , three pin top , regulator
Tender For corrigendum : supply of ht motors spares for emd-1,wtps,gsecl. - skf make induction heater model no. tih 100m / 230v for bearing fitting work., hydraulic jack with pump & accesories capacity: 100 mt., hydraulic jack with pump & accesories capacity: 50 mt., greasing pipe for ht motors - r1 type hydraulic hose pipe ( rubber hose with single inner wire braiding), araldite 180 gram/tube, red insulating varnish-class f epoxy insulation & protection coating., dr. back make backtol red in 1 lit. tin varnish, digital multimeter 4.1/2 digit (true rms), digital clamp on meter lcd display with backlight, 3-3/4 digit., digital megger (insulation tester) dual voltage 500/1000 v 0 to 2000 megaohms resolution of 1 m? weght: 500 gm approx., analog multi range insulation tester.hand driven type,voltage range-250v/500v/1000v., brass connectors for pstb of ht motor, plastic dori (sutari) for binding of plastic ,0.5 thick &2mm width., insulating cable gland for pstb of ht motor, grease gun, fevicol sr 998 (200 ml/tin), self fusing rubber tape black , class b , 31 kv die electric strength , size 2.5 cm x 10 mtr., pvc tap roll, insulating box for pstb for ht motor, ht pvc insulation tape size 0.18 mm x25 mm x 65 mtr length, 6.6 kv busbar /cable couductor protection heat shrinkable sleeve dia .before shrink:50 mmdia. after shrink :20 mm, heat shrinkable sleeve,size:45mm/18 mm( for 240/300 sq.mm )for 11 kv, 6.6 kv busbar /cable couductor protection heat shrinkable sleeve dia .before shrink: 75 mm dia. after shrink : 28 mm for 11 kv ht cable, z 801 fast steel epoxy stick (1 stick - 114 grm), impact wrench power/battery operated, cordless screw driver power/battery operated, w963 play safe high voltage tape (50 mm x 0.76 mm x 9.1 mtr) roll, w963 play safe high voltage tape (25 mm x 0.76 mm x 9.1 mtr) roll, becktol gray varnish in 1 ltr tin dr.back make, electical saftey equipment tester taparia product no:814 voltage range:110v to 230v