Get complete information related to latest Bearing Shell Tenders . from India at Classic Tenders. Search the best available tenders from Indian government tenders, domestic Bearing Shell Tenders , private tenders, online tenders, tender invitation notice, business tender notices, online tenders and bidding Bearing Shell Tenders.
Tender For corrigendum : supply of msu tube kit consisting of eleven items (for t.m. 4907) drg. no. as in table sn 1 pl no. 12495694 suspension tube for tm 4907 drg. no. 1/dcw/m/tm-398 alt x qyt. 01 nossn 2 pl no. 12495669 grease nipple for msu drg. no. 4/dcw/m/tm-420 alt nil qty. 02 nos sn 3 pl no. 12495657 socket hd cap screw (m12x90) drg. no. 4/dcw/m/tm-422 alt y qty. 08 nossn 4 pl no 12495633 socket hd cap screw (m12x30) drg. no. 4/dcw/m/tm-421 alt y qty. 06 nos sn 5 pl no. 12495645 socket hd cap screw (m12x70) drg. no. 4/dcw/m/tm-423 alt y qty. 08 nos sn 6 pl no. 12495621 encloser for msu drg. no.1/dcw/m/tm-419 alt nil qty 01 nos sn. 7 pl no. 12495610 end cover gear wheel side drg. no. 1/dcw/m/tm-417 alt nil qty 01 nos sn 8 pl no. 12495608 abutment piece for msu drg. no. 4/dcw/m/tm-418 alt nil qty. 01 nossn 9 pl no. 12495580 end cover road wheel side drg. no. 4/dcw/m/tm-416 alt nil qty 01 nos sn 10 pl no. 12495566 bearing housing for msu drg. no. 4/dcw/m/tm-414 alt nil qty 01 nos sn 11 pl no. 12495578 adjustment washer for msu drg. no. 4/dcw/m/tm-415 alt nil qty 01 nos ]
Tender For auction sale of depot ferrous scrap - scrap u/s miscellaneous cutting bits, ms / wi nuts, screw, bolts, pins, pcs. of coil springs, p.way fittings, erc, brake head, anchor link with or without silent block, brake shoe, small rail pcs., cotter, main bearingshell, inner outer races, p.way /dsl loco/c&w parts & fittings of sorts & sizes. location: bin no. 328
Tender For auction sale of depot ferrous scrap - 98050126 scrap ferrous material consisting of various type of nut, bolt, rivets, peices of angle, channel, m.s. bracket, draft gear spring washer,m.s. liners,piston, door hinge, door hinge foot, small cut peices of tie bar, beater, clamp, pully side bearer housing, brake wear plate,side bearer housing top and bottom, knuckle pin, knuckle thrower, dog spike, g.i. ohe fitting, bk hanger lever, fish bolt, parts of ctrb bearing, liner, small p.way fittings, bk shoe key, s/pin, pu pad, axle box cover, and inner outer rings, m.s. pins, s/plate, peices of s.s and m.s. pipe, peices of huck bolt fresh cutting, push rod, cbc uncoupling rod, cbc lock and cbc components, safety loop, bk shoe head, released valve, cut peices of m s sheet, plates, buckles, ohe fitting, peices of ms rounds, equalizing lever, bridle bar, shackle stone, shackle, stricker casting wear plate, yoke pin, side bearer liner plate, hand brake wheel, suspension socker, g.i. nut bolt, tension device, main pull rod, cbc uncoupling rod, yoke pin, c.c. pad plate, m.s. round, bk shoe head, bk beam plate, reservoir tank patti, door catch, door check spring, annual repair supporting bracket, signal ground connection parts and other small wagon components and other ferrous items if any.
Tender For corrigendum : supply of double end ctrb mounting machine for mounting the ctrb simultaneously from both ends of wheel set, cap. 70t. as per technical specification given below : (1) hydraulic power pack : double speedmaximum working pressure of 450 kg/cm2 pump, pcm, level gauge, breather, strainer and pressure gauge etc will be installed in the power pack. (2) piston stroke of the cylinder : 450 mm (minimum) (3) capacity of the machine : 70 ton(4) speed (i) advance (idle stroke) 800 mm/min (+/-10%) (ii) installation : 110 mm/min (+/- 10%) (5) type of cylinder :hydraulic double acting (6) jack adjusting height from rail level to centre of installation tube : 360 to 560 mm (7) type of wheel lifting jack : supporting guide jack system with machine frame. ( 8) bearing mounting final pressure : 50+/-tons (will be held for 05 seconds) (9) type of pressure gauge : marking of pressure gauge will be dial in parallel measured in tones and kg/cm2 (10) time of both side mounting of bearing : not more than 2.5 minutes. make : sumanglam. technical specification attached. at annexure a. [ warranty period: 30 months after the date of delivery ]
Tender For charge trolley assembly as per the part no. 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16,17, 18, 19, 20, 21, 31, 32, 33, 34 & 35 of rwf drawing no. 712210510120 with quantity as mentioned in each part nos. (part no.1- 04 nos., part no.2-025 nos., part no.3- 04 nos., part no.4- 01 no., part no.5- 01 no., part no.6- 04 nos., part no.7- 02 nos., part no.8- 04 nos., part no.9- 12 nos., part no.10- 04 nos., part no.11- 02 nos., part no.12- 04 nos., part no.13- 04 nos., part no.14- 04 nos., part no.15- 02 nos., part no.16- 08 nos., part no.17- 24 nos., part no.18- 04 nos., part no.19- 04 nos., part no.20- 08 nos, part no.21- 04 nos., part no.31- 01 no., part no.32- 01 no., part no.33- 02 nos., part no.34- 08 nos. & part no.35- 02 nos.). note: (1.) items shall be supplied in the assembled condition. (2.) bearing shall be of make skf/fag/ntn/timken only. (3). wheel support casting (item no.02) shall be radiographically tested at nabl accredited laboratory and the test report shall be followed along with the supply. (4.) material test certificate from nabl accredited laboratory shall follow the supply. (5.) warranty as per standard irs conditions. (6.) items shall be packed suitably to avoid damages during transit. [ warranty period: 30 months after the date of delivery ]