Latest belt feeder Tenders | Government belt feeder Tenders

State Government

CTN :40227801

27 May, 2025 49.58 Lacs

Gandhinagar - Gujarat

Tender For various routine/preventive and breakdown maintenance work on as and when require basis at chp-gtps - replacement of hammer rings for stage ii crusher , replacement of hammer rings for stage i crusher , replacement of screen plate / breaker plate/kick off plate of stage i and ii crushers , replacement of rotor of stage i crusher with disassembling of removed rotor and assembling of new/repaired rotor , replacement of drive end side bearing / pedestal of crusher rotor or complete gear coupling set of crusher or repositioning of dislocated rotor of crusher , replacement of non drive end side bearing/pedestal of crusher rotor or complete alignment of crusher motor with crusher rotor , replacement of broken hammer rings of stage i and ii crushers (stage i crusher up to 12 nos.of hammer rings and stage ii crusher up to 06 nos. of hammer rings at a time) , replacement of rail of rail table of wagon tipplers 1/2/3/4 (in one side full length) , replacement of clamping rubber pads of clamp for wagon of wagon tipplers , replacement of whole resting pads for wagon of side beam of wagon tipplers , replacement of spill plate roller of wagon tipplers , repairing/preparation/ fitting and replacement of hooks/rods/turn buckle, chain, sling rope ,spring assembly etc. of vibrating trays and crusher house trays , spillage control at various locations , miscellaneous cutting/welding work require at various locations , replacement of gearbox in conveyor no. 2a/b,11a/b,12a/b,13,14/15,16a/b,17a/b ,18a/b,drc/apron/rg/,wagon tipplers,stacker-reclaimer , replacement of gearbox in conveyor no.,5a/b,8a/b,10a/b,shuttle conveyor 1/2,belt feeder 1/2 ,roller screen, mrc 3/4/5,wobbler feeder ,dribble conveyor 1/2 , replacement of slow speed coupling set (two halves) of drive pulley , replacement of coupling bolts and rubber bushes of slow/high speed coupling(input/output coupling ) in conveyor no.2a/b,11a/b,12a/b,13,14/15,16a/b,17 a/b,18a/b,drc/apron/rg/,wagon tipplers,stacker-reclaimer , replacement of coupling bolts and rubber bushes of slow/high speed coupling(input/output coupling ) in conveyor no.,5a/b,8a/b,10a/b,shuttle conveyor 1/2,belt feeder 1/2 ,roller screen, mrc 3/4/5,wobbler feeder ,dribble conveyor 1/2 , replacement/removing/refitting of various size and type of fluid coupling , replacement or removing & refitting of any internal/bearing/input/ output oil seal of various size and type of gear box , overhauling of dismantles old/used gearbox in all respect with fitment of input and output coupling. , replacement of drive pulley , replacement of drive end side bearing of drive pulley or repositioning of dislocated drive pulley , replacement of non drive end side bearing/any side pedestal of conveyor drive/non drive pulley , alignment of motor/ gearbox/drive pulley including decouple/couple of coupling , nut bolt and drive system checking with replacement of broken nut bolt in all 04 wagon tipplers no.1/2/3/4 as per scope , lifting and releasing of gravity take up of any conveyor belt for locking and de locking of belts for other than belt replacement work , loosening and tightening of horizontal type screw take assembly of any conveyor belts for other than belt replacement work , work of dismantling and re erection of new/repaired apron pan from existing apron feeder of wagon tippler , repairing of upper/lower structure/cone plates of damaged/bend apron pan , replacement of carrying roller of apron feeder , replacement of worn out/ damaged ti roller and garland rollers. , replacement of worn out/ damaged impact rollers , replacement of worn out/ damaged return rollers , replacement of various worn out/ damaged ti roller stands , replacement of various worn out/ damaged impact roller stands , replacements of various worn out/ damaged return roller stands , replacement of various worn out skirt rubbers [10 m each] and skirt rubber with angle , preparation and replacement of guide rollers with bracket in place of worn out/ damaged guide rollers as

State Government

CTN :40055046

08 May, 2025 90.32 Lacs

Satna - Madhya Pradesh

Tender For office and security equipment - b.p. machine digital, analog weight machine, digital weight machine, wheeler, stretcher, vaporizer, nevulizer machine, needle cutter, infrared thermometer, walker, crutches, desert cooler, alcohol / breath analyzer, thermometer, needle holder, thumb forceps, procto scope, boiler, oxygen flow, oxygen mask, surgical scissor, glucometer, haemoglobin meter, oxygen cylinder, pulse oximeter, computer system, ups, printer, keyboard, multi colour printer, cpu, photocopy machine, intercom number display, web cam, finger print machine, walkie-talkie (05 km. range), projector, lcd tv 32 inch, sound box, telephone, ceiling fan, alarm siren, torch, exhaust 18 inch, mic, column speaker, computer sound, cordless mic, collar mic, mic with lead, cassio large including, harmonium, dholak, jhinka, majira, walkie-talkie charger, printer drum, trumpet, solar plant 03 kw, camera, laptop, digital camera video, r.o., cooler, hand metal detector, locks, cctv camera, stick, intercom set 16 pieces, body protector, scanner, walkie-talkie static set, logi tech camera, body worn camera, deep search metal detector, air conditioner, inverter, solar power battery, lcdtv 42 inch, lightning conductor, insect killer machine, generator, fogging machine, dough kneading machine, ptz camera, door frame metal detector, search spot light, high mast light, night vision light, public announcement system, handcuffs, trimmer saver, "offset machine1- machine should have minimum 02 years warranty and should be of automatic print. (for prison industry)2. bag and paper size - 15x203. printing area - 14x204. sheet size (max) - 508x381 mm5. power consumption - 1.75 hp ( single phase)6. average production speed- 2000-3000 per hour7. feeder capacity- 515 mm8. plate size- 520x400 mm9. printing area -14x2010. speed- 1500-6000 iph11. delivery capacity -430 mm12. drive motor- 1 phase 0.75 hp"

State Government

CTN :40216185

07 May, 2025 NA

Chandrapur - Maharashtra

Tender For procurement of rotary coal feeder bearing housing driving and non- driving cover plate in unit 4 during aoh at cstps, chandrapur

CTN :40222106

02 Jun, 2025 42.37 Lacs

Ashoknagar - Madhya Pradesh

Tender For supply of electrical materials for the repair and maintenance of street lights as per the boq - t-5 power/energy saver 2x24w choke, t-5 power/energy saver 24w ftl tuberod, 2x24 t5-holder, t5 power saver 2x24 fixture acrylic transparent cover, t5 power saver 4x24 fixture acrylic transparent cover, 150w hpsv choke, 150w hpsv lamp, capacitor 33mfd 250vac 50 hz, electronic ignitor suitable for 150w hpsv lamps, 150w holder, led driver 50w bis certified, led mcpcb plate 50w, led mcpcb plate 100w, led mcpcb plate 150w, supplyingof isi marked and approved make of moulded case circuit breaker(mccb) suitable for 3phase,3pole,50hz,415 volts, ac supply with respective interrupting capacity(ka) at 415 volts cited against their range standard conforming to is - 8828: 8.1mccb with breaking capacity 25 ka at 415 v: current rating -125 amps & 70% -100% adjustable, supply, installation, testing and commissioning of sovp device should have single high capacity varistor in the l-n plug and encapsulated spark gap for n-pe, l-n sovp should have a rated voltage of minimum 320v ac to handle indian power supply conditions. sovp should have visual indication on replaceable varistor and spark gap modules as well as a potential free contact on the socket for remote indication. sovp device should be wired up as per tt configuration of wiring in accordance with en 61643-11 standards. both the l-n and n-pe, spds should be rated for handling 30ka of nominal 8/20 s surge current.: sovp for pole light sub feeder panels - type 2 pluggable spd 3+1, rating l-n/n-pe uc 255/320 v in 30/60ka ka, lmax 30ka/60 ka, up 1.5kv, supplying of isi marked and accepted standard of miniature circuit breaker(mcb)ofcseries suitable for 240/415volts,50cycle,10 ka value ac supply confirming to is:8828:1996,iec:60898 :2002 but without enclosures: single pole 63 amp., astronomical timer with dst feature, contactor 3 pole 90 amp 50hz 415volts with no-nc contacts, tpn connector 150a, supply of approved make powder coated sheet steel encloser spn mcb db inclusive of busbar,neutral bar,earth bar & two earth terminals etc. complete as per is:13032 (exclusive of mcb & isolator): 8 way double door, supply, installation, testing and commissioning of sovp device should have single high capacity varistor in the l-n plug and encapsulated spark gap for n-pe, l-n sovp should have a rated voltage of minimum 320v ac to handle indian power supply conditions. sovp should have visual indication on replaceable varistor and spark gap modules as well as a potential free contact on the socket for remote indication. sovp device should be wired up as per tt configuration of wiring in accordance with en 61643-11 standards. both the l-n and n-pe, spds should be rated for handling 30ka of nominal 8/20 s surge current.: sovp for pole light - type 2 pluggable spd 1+1, rating l-n/n- pe uc 230/400 v in 5 ka, imax 10 ka, up 1.2kv, led batten tubelight 20w, supplying of approved make tpn mcbdb metal double door with provision for fpmcb/isolator/rccb/rcbo as incomer and sp mcbs as outgoing inclusive of busbar,neutral bar,earth bar & two earth terminals etc. complete as per is:13032 (exclusive of mcb & isolator ): 8 way (8+24), 8 sq.mm multistrand pvc insulated copper wire bundle 90mtr, 1.sq.mm aluminium single core wire bundle of 100mtr. isi marked, xlpe insulated power cable( conforming is-7098 part-1) 1100 volt grade 2-core isi marked with alu. stranded/solid conductor: 16 sq.mm unarmoured, xlpe insulated power cable( conforming is-7098 part-1) 1100 volt grade 4-core isi marked with alu. stranded/solid conductor: 16 sq.mm unarmoured, xlpe insulated power cable( conforming is-7098 part-1) 1100 volt grade 1-core isi marked with alu. stranded/solid conductor: 25sq.mm unarmoured, wooden ladder 21ft, toolkit set consisting of different sizes l-keys, screw drivers, testers and plier set., taperoll box consisting of 30pcs (conforms to is: 7809 (part 3, sec 1),self extinguishing,protects from electrolyt

CTN :40078132

10 May, 2025 67.13 Lacs

Sundergarh - Odisha

Tender For corrigendum : tender for supply of mill and coal feeder spares - xrp883 grinding roll lock nut , xrp883 seal wear ring of as per drg no , xrp883 journal head air seal ring , xrp883 scraper holder liner of bowl mill , xrp883 liner for scraper bracket , xrp883 scraper assembly bowl mill xrp883 , xrp883 restiction ring segment separato , xrp883 journal head guard left , xrp883 journal head guard right , xrp883 upper bearing housing guard of rj , bearing cap drag link assy coal feeder , xrp883 bush for spring assy , flange for head pulley bearing housing , idler housing for gravimetric feeder , feeder gear box coupling , gravimetric feeder discharge chute , xrp883 clamping ring set 1 set equal to 4 nos , xrp883 lock nut of main shaft , xrp883 shim for journal bearing housing , xrp883 shim for air seal ring upper , xrp883 body liner 2 , xrp883 journal liner assy part 3 , xrp883 outlet plate liner mill discharge , take up unit r c feeder , weigh pulley housing for feeder , side skirt coal feeder right side , side skirt coal feeder left side

CTN :40208695

08 May, 2025 NA

Villupuram - Tamil Nadu

Tender For replacement of cane carrier side plate, feeder table bottom and side plateentrusting work

CTN :40195442

22 May, 2025 NA

North 24 Paragana - West Bengal

Tender For supply of xlpe cable for working voltages up to and including 1.1 kv as per is 7098 (part 1) (q2) , mcb - miniature circuit - breakers for a.c. operation as per is / iec 60898 (part 1) (q2) , supply install testing commissioning of step down transformer indoor type voltage rating ht11 bye zero point 433 kv out door type of capacity 200 kva level 2 3 phase 4 wire 50 hz , supply laying and testing 11 kv earthed grades cable xlpe 120 sqmm 3 core , s and f cable end jointing kit for 11 kv grade cable for outdoor termination heat shrink type cable end complete with jointing material and accessories , s and f cable end jointing kit for 11 kv grade cable for outdoor termination heat shrink type cable end , material and labour for pcc 1 ratio 4 ratio 8 type d2 using 40 mm graded stone aggregate for making good cutting portion mass concrete , m and l for pcc 1 ratio 3 ratio 6 type c2 using 40 mm graded stone aggregate for making good cutting portion mass concrete filling of foundations etc including necessary use and waste of form work , supply and fix tpn distribution board 4 way acrylic door 415 volts ac tpn for flush mounting with 100 amps double door copper busbar neutral bar earth bar and mcb incomer of rating upto 100amps , material and labour for earthing complete with galvanised steel earth plate electrode 600 x 600 x 6 mm thick buried directely in ground vertically , supply install testing and commissioning of lt feeder panel of size 1500 x 1500 x 600 mm 3 phase 4 wire 415 v 50 hz ac outdoor type , m and l for brick sub class b 250x115x75 mm and laid in trenches as in protection of ug cable , supply and filling in and spreading unwashed river sand for cushioning and covering the under ground cables in trenches and punning to provide required cover , returning filling in soil including spreading leveling watering and well rammimg in layer n exc 25 cm complete all as specified and directed , removing excavated soil not exc 50 mtr ant depositing where directed at a level not exc 1 point 5 mtr above the starting point all as specified and directed , m and l for gl pipe 100 mm light grade laid in trenches floors bye on pole bye road for cable protection with all fittings complete all as specified and directed , boaring holes horizontally under road without damaging the surface of road minimum1pointzero mtr bellow the road surface with the help of gl tubing of any dia not exc 80mm dia for passing of ug cable , supplying and laying reinforce precast concrete cable cover class ht type 1 flat size 300 x180x40 mm for protection under ground ht cable complete all as specified and directed

corporations/Associations/Others

CTN :40170739

10 May, 2025 4.95 Lacs

Bankura - West Bengal

Tender For supply of disc valve gate swing size12topbottom for transfer hopper spares for transfer hopper ahp u4 , complete set bottom gate valve for transfer hopper of u4 size 12 , disc holder pin 25 130lspare for nuva fedder diffuser1210 , spring 01 set04nosod 1570lspares for nuva feeder diffuser1210 , spring lock plate spares for nuva feeder diffuser12 10 , pivot ball assy for fly ash diffuser intake vv drg 25po1t1b023 , 212 vent n equalizing valve as per drg no23p01t1b120 disc full faced ceramic lined on one side 2 12 2way vent valve , chromium coated slide 9spares for tersg 9 for ash handling plan u4 , slide part no2 for fly ash header valve tersg 8 fly ash header valve tersg as per drg no25p04t 1b040r1 , chromium coated slide 11 spares for tersg 11 for ash handling plant u4 , 4vent valve2 way ac operated removable valve seat flanged connection but without air cylinder and limited switch for 4vent n equalising valve , seat gate hi chrome astm a532 class iii 4 vent valve for 4vent n equilising valve , disc gate hi chrome astm a532 class iii 4 vent valve for 4 ventn equalising valve , disc gate of nuva feeder size12inch10inch material hi chrome astm532a gr iii bid number/ & ( * ) : gem/2025/b/6175226 dated/ + : 29-04-2025 bid document/ 3 3 1 / 20

Central Government/Public Sector

CTN :40161619

09 May, 2025 24.58 Lacs

Sundergarh - Odisha

Tender For painting of poles, danger plate ht/lt, anti clamping device, retro reflective sticker with pole no. and feeder no. and waterproof ip65 strip light at kulda ocp basundhara area

Co-operative

CTN :40120374

12 May, 2025 NA

Udhamsign Nagar - Uttarakhand

Tender For c s item on conversion supply basis and forged steel item - c.s coupling having material as per is:1030 grade 280-520w for mill size 30"x60" as per drg. supply basis, conversion basis, machining charge, cast steel crown pinion having material is:2708 grade-iii-b for mill size 30"x 60" as per drg.supply basis, conversion basis, machining charge, c.s.trash plate having material as per is:1030 and grade-iii-b supply basis, conversion basis, machining charge, teeth cutting/grooving of trash plate as per drg., c.s.trash beam as per is-1030/is 2708 as per drg.supply basis, conversion basis, machining charge, forge steel tail bar for taxmaco and kcp mill having material c-40/8 as per drg. mh- 6 & mh-56supply basis, conversion basis, forge steel pinion for transmission gear of taxmaco mill as per drg. no. mh 39,material en-24,tensile strength70-80 kg./sqcm, hardness 200-220 bhn, c.s.bearing housing for taxmaco mill as per deg no mh-17-c/04 side roller housing supply basis, conversion basis, c.s.bearing housing for k.c.p.mill as per drg no mh-17-b side roller housing supply basis, conversion basis, c.s.bearing housing for k.c.p.mill as per drg no mh-17-b top roller housingsupply basis, conversion basis, c.s.gear coupling for c/f machine as per drg.no.bh-14 (duly case hardness), c.s. pinion for cane unloader as per drg, cu- 16teeth-17, teeth -18, c.s.sprocket 2" pitch (both pilot bore)(i) no of teeth 18 , boss dia 3", (ii) no of teeth 36 , boss dia 6", c.s.sprocket for boiler rotary feeder as per drg.blr-73/1 pitch- 25.0 mm,no of teeth 21, od -180mm. p.b -25 mm, c.s.sprocket for bagasse elevator (pilot bore) as per drg.mh-75 pitch 50.8 mm,no of teeth 50, od 842.70mm. pcd 808.7mm,teeth thickness 28mm , boss- 270x130 mm, cs sprocket (pilot bore ) as per drg.blr-62 pitch 50.8 mm, no.of teeth-14 pcd 226.49mm,od 258.8mm, static coller of 25 mm thick duly hard faced of 5 mm thick layer . total thick 30 mm after hard facing for taxmaco & kcp mill as per drawing no. mm 105(i) m.s. material, (ii) c.s.material, sprocket of inter carrier od 280 mm,no.of teeth 45.pitch 19.5 mm, c.s. sprocket (duplex) for enter carrier teeth 12, as per drg. mh-72/sample, s.s. wear plate is 304 quality (i) length 435 mm x width 370 mm x thick 15 mm, (ii) length 385 mm x width 330 mm x thick 15 mm, c.s.tresh beam bracket as per sample /drg., c.s.eccentric pin trash bar adjusting device as per drg. mh-133/2024-25, c.s. trash beam adjusting connecting rod for taxmaco mill, as per drg. mh- 297, c.s. bridge wheel for cane unloader as per drg. cu25 (1),, trolly wheel for cane unloader as per sample /drg., pinion gear set for cane unloader as per sample /drg, c.s. pinion (gear) for rbc cross carrier pitch 41 mm. teeth 25 , type of teeth in valute (spur) module 12.7 mm width 125 mm .od 343 mm, bore 2" dia as per drg., clutch shaft for mill. as per drg. mh-76 , en-8for taxmaco mill -sl.no.2, for kcp mill - sl.no.1, cs worm for crystilizer wheel od 290 mm, bore 81 mm.pitch 80 mm complete, groving of c.s. trash plate as per drg., idler wheel gear for cane unloader., no of teeth 68, od-420 mm, module-6, pitch- 18.84 mm, pcd-408 mm, as per drg. no. cu-25 (i), pinion for cane unloader no. of teeth- 33, od-212 mm, pcd-198 mm, pitch- 18.84 mm, module-6 as per drg. no., pinion for cane unloader no. of teeth- 18, od-200 mm, pitch- 35 mm, bore- 50 mm, width-115 mm, module-6, teeth depth-25 mm as per drg. no., break stand complete for cane unloader, size-10", cs sprocket of rbc, nos of teeth 12, as per drg. blr 32/93, chain sprocket for inter carrier clucth shaft, od 280, pcd 270, bore 108, root dia 260, nos of teeth 45, nos of hole 4, as per drg. 001, pinion for transmission gear kcp mill, material en-24(as per drawing no. mh-95/2024-25), c.s. helical teeth pinion, teeth-20, od-60, bore-26, pitch-10(as per drawing no. bh-rg-05/2024-25), c.s. helical teeth pinion, teeth-17, od-62, bore-28, pitch-13(as per drawing no. bh-rg-04/2024-25), chief engineer

Belt Feeder Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

State Government

State Government

State Government

corporations/Associations/Others

Central Government/Public Sector

Co-operative