Tender For supply of soil investigation work including conduction of standard penetration test up to depth 6 m as given in sl no 1 of specification document , direct shear test as given in sl no 2 of specification documents , tri axial shear test as given in sl no 3 of specification document , consolidation test as given in sl no 4 of secification document , field density as given in sl no 5 of specification document , liquid limit as given in sl no 6 of specification document , plastic limit as given in sl no 7 of specification document , specific gravity and others as given in sl no 8 of specification document , relative density as per soil condition as given in sl no 9 of specification document , determination of ground water table as given in sl no 10 of specification document , settlement analysis determination of bearing capacity of soil at foundation level as given in sl no 11 of specification document
Tender For purchase of equipments - purchase of equipment, 1. configuration design an 8-channel battery analyzer and its accessories 2. power 425 w3. voltage measuring range: 25 mv to 5 v, discharge minimum voltage: 0v or better, accuracy: 0.05% of fs4. current range: 0.5 ma to 6 a, accuracy: 0.05% of fs or better 5. power per channel output power: 30w, stability; +/- 0.1% of fs or better6. time rise time: 1ms (0~full range)7. frequency 10hz8. charge mode of operation: cc, cv, cccv, cp end conditions: voltage, current, relative time, capacity.9. discharge mode of operation: cc, cv, cp, cr, end conditions: voltage, current, test time, capacity, energy.10. pulse mode charge: cp mode, cc mode, discharge: cc mode, cp mode, min pulse width: 500ms, automated switch: automated switch from charge to discharge for each pulse end condition: voltage, relative time11. dcir support for the calculation of the point of the dcir12. cycle cycles: 1 65500 or better, steps: 250 or better, nested function: max three levels of loops13. protective function software, power-down data protection, user-defined safety (upper and lower) tolerance of current, voltage, and delay time14. channel features independent pairs of closed loops for the constant current source and constant-voltage source15. test reports and curves for analysis different types of curves created by software based on user definition. (voltage-time curve, current-time curve, capacity-voltage curve, loops times charge/discharge capacity curve, loops times charge/ discharge efficiency curve, etc.), data reports created by the software. comparison of the performance of the batteries tested in channels, both visually and statistically16. channels independent control17. ac input ac 220v 10% / 50hz 18. voltage and current testing sample 4 wire connecting 19. noise 85db20. data management mysql database21. communication means tcp/ip protocol22. data output excel, txt23. communication interface ethernet port24. number of channels per cabinet 825. accessories: 1. bi-potentiostat: electrochemical workstation or moduletechniques the system should be capable of running the rde / rrde technique simultaneously cyclic voltammetry (cv) with simulation/fitting programs linear sweep voltammetry (lsv) with stripping bulk electrolysis with coulometry (be) differential pulse voltammetry (dpv) with stripping normal pulse voltammetry (npv) with stripping tafel plot (tafel), potentiodynamic deactivation, pitting corrosion, corrosion rate, linear polarization, corrosion current, etc. multi-current steps (istep) amperometric i-t curve (i-t) lifetime testing open circuit potential time (ocpt) chrono amperometry (ca) chrono coulometry (cc) chronopotentiometry with current ramp (cpcr) potentiometric stripping analysis (psa) auxiliary signal measurement channel ir compensation external potential input galvanostatic charge discharge single/multiple cycle -chrono potentiometry (cp) with potential limits, polarity by potential or time, no. of cycles etc. voltage vs current density curves single or multiple potential steps with charge limits, single or multiple current steps, mixed voltage/current control using macro. i-v measurements, i max, pmax, fill factor, etc.impedance ac impedance (imp) 10 hz to 3mhz impedance time (impt) (mott-schottky) impedance potential (impe) impedance simulator with fitting open circuit potential time (ocpt)hardware specification of bi-potentiostat workstation/ module: potentiostat / galvanostat module, 2- or 3- or 4-electrode configuration maximum potential: 10v, maximum current: 250 ma peak or better and 2 amps with +/-25 volts for higher current measurement. compliance voltage: > 13v or better, potentiostat rise time: 300 ns or better galvanostat applied current range: 3na to +/- 100ma or better and upto 2 amps applied current accuracy: 20 pa or better input bias current: 1 pa or better cv and lsv scan rate: 0.000001 to 10,000 v/s. ca and cc pulse width: 0.0001 to 1000 sec imp frequency: 0.00001 t
Tender For supply of ismb 200mm x100 mm x 5. 76 mm thickness, 06 mtr long , ismb 200mm x100 mm x 5. 76 mm thickness, 04 mtr long , ismb 200mm x100 mm x 5. 76 mm thickness, 09. 5 mtr long , ismb 200mm x100 mm x 5. 76 mm thickness, 4. 2 mtr long , cgi sheet 13 feet x 3 feet x 063 mm thickness , non woven geosynthetic filter fabric 200 gsm , paint sundrenched sand - 7t 1589 , paint lucky clover 4a0912 , paint brown eyes 08a2802 , graded beaker borosil , only 12 balls for los angle machine, for abrassion test machine , diamond impregranted core reinforced , cube mods 150 x 150 heavy duty , pedo meter , standard sand is-2720 for field density test , plain gi sheet size 3000 mm x 900 mm x 0. 40 mm thickness , self- drilling screw hex washer zinc with 16 mm black bonded washer for 6 mm thickness steel size 12-14 x 55 mm