Tender For supply of bogieframearrangement to drg. no. dmu/tc7-0-3-701/col.i alt -d, col-i (without nylon bushes whereever applicable). material tc required from oem/nabl approved lab. warranty certificate required as per irs condition. [ warranty period: 30 months after the date of delivery ]
Tender For supply of bogieframearrangement for emu trailer coaches with 180/150kn air spring-(qr code as per cde/rcf letter no. md44121 dt. 24.11.2021.), as per drawing: icf/mrvc/d-0-3-001 alt.'lr1' col.1 (without bush to drg. no. emu/m-3-2-060), packing instruction: bogieframe (pl nos:- 35327017, 30984348, 30986000, 30985912) each guide on bogieframe to be properly wrapped with biodegradable transparent plastic sheet. machined portion of bogieframe components shouldbe covered with suitable eco friendly cushioning material. wooden/suitable spacers havingadequate strength to be provided between bogieframes to prevent rubbing against each other during transportation/loading/unloading. supplier to ensure that bogieframe shouldbe transported with utmost safety till unloading in cs/avd so that components are not damaged fitted on bogieframe and dimensions duly maintained. a list (easily visible) should bepasted on each box showing po no. , pl no., description, drawing. no./spec, qty, firm's name &address and dispatch detail etc. for identification. transit damage if any shall be at the cost of supplier. , proction procedure: as per drawing [ warranty period: 66 months after the date of delivery ]
Tender For corrigendum : supply of ballast rake , cross pen hammer 500 gm , light weight spanner for 60 kg rail. , log line with 20 kg lead ball . , piano wire with clamps , probing rod , rail tongue , schmidts hammer , versine kit , craw bar , drill bits of hss , hammer 3kg , hydraulic track jack 15 ton , inspection cum chipping hammer , retro reflective tape 45m each roll yellow , shovel with handle , straight edge , grinding wheel , abrasive rail cutter disc , hydraulic track jack 15 ton , pan mortar , rail dolly , rail thermometer , small testing hammer , speed restriction board 60 75 , stop board with stand and chain , plumb bob , chisel , flexible pipe 1 for gardening , mirror 10x15 cm , screw driver set , shears for gardening , trowel for gardening , whistle board , whistle , combination plier
Tender For supply of aluminium door 7 ft x 3.5 ft , tile 2ft x 2ft , aluminium sliding window 4 x 4 ft , tile 1 ft x 1ft , wash basin with pedestal , ewc with flush tank , connection pipe , cp shower rose round , cp towel rail , cp bib tap , insulation tape , cp soap dish , cp grating doom , jet spray , mat mesh type red colour 8ft x 8ft , mattress 6 ft x 6ft , carpet 6 ft x 4 ft , wash basin mixture tape , wash basin tape , 0.5 hp water pump motor , karandi iron , brick hammer , dia set 15x20x25mm , hydraulic door closer , led round ceiling light 18 wt , cp hand jet spray , cp waste coupling
Tender For auction sale of depot ferrous scrap - old used and u/s signaling items i.e. complete signal units, electronic lifting barrier, signaling pole latice with ci attached, cable termination rack, location box full &half, armed wire, sliding boom complete, operating panel, padestal, ristrictor wearing plate, gi boom for elb, nbt block instrument, point machine chasis with accesaries with minor nf attached, lock lever, stop disc for lb, winch m/c, ground connection, rail attached ms board, ms board with angle, ms rusted bars, rods, fire bucket, electric lifting barrier and other signaling items with minor nf attached, c&w items i.e. various types and sizes broken springs, inner springs, released bogie beams offsized outer springs, broken cbc body, striker casting wear plate, man hole cover, pull rod, push rods, plates, knucle pin, brake beams, cp top, knuckle, draft gear box, adeptor, push rod, safety bracket, brake shoe, pin, nut bolts, top side liners, stricker, primary verticlal damper, yaw damper, vertical shock absorber, vertical sec damper, lateral damper, axel end cover, centric disc, fastners, fire extingyishers offsize & type, beater, pick axe, shovel heat, mechanical jack, hydraulic jack, pad lock, hammer, gi wire, basket, tin case, offsize rack ballast, bucket gi, pan iron, ohe items i.e. offsize and type insulators, ohe high mast cut pieces and other ohe items, ms bond patti, blow lamp, structural clamp, isolator assembly, various boards, retro reflactive number plates, junction box, small chain, anti climbing device, hot rolled steel flat, fuse switch assly, padestal, cantilever assly, da-2, caution board, guy rod with mast & guy attached bolt items of electric and power department i.e. pawrah, el box, switches, etc items of works department i.e. ms angle, plates, ms patra, ms i sections, gi gater, parline, tmt bars, gate post, gate flap and other ms items with some rail pieces attached, items of tele department i.e. cgdb pole, ms boxes, items of p way department i.e. rail dolly, push trolly, self propelled motor trolly, hand cart, gi case, broken tiebars, ms engineering boards, rail cum road trolly, ms clamp for joggle fishplate, rail tongue, st slipper, all types of lc boards, ms pipe, ms fishplate, hs lamp, rail toung, whistel thunder, hand operated cutting m/c, hydraulic jack, office clock, dubber for gate lamp, gi bend, broken bdds rsp tool kit, broken bomb blank vehicle search mirror, lock pad, skv welding set, rusty cst 9 port, ms sheets, chequered plate, cc cribs, may have some ss items (the above items may be with minor nf attached or may not be) (the above items may have rusty and dusty or may not be) ( cuting allow for easy loading before delivery) mode of delivery- by weight location - scrap yard & i/f of godown 6
Tender For supply of fabrication and erection work e e - places , replacing wornout runner base and installing a new runner base of cane carrier and baggage elevator and r b c , replacing wornout runner with new one of cane carrier and baggage elevator and r b c , removing wornout angle iron and t iron of the cane carrier and reinstalling it by straightening the crooked part , removing the wornout part of the suit from different places and fitting it with new one , chevron grooving of new rollers of the mill , chevron grooving of old rollers of the mill , remove the wornout partition plates of the juice box above and below the juice heater by 10 or 12 mm ms plate and install it , installing ribs at the top and bottom partitions of the juice heater , repairing save all of qurdbody , removing old wornout gutters installed at various places and installing it with new gutters , remove the old wornout save all from pan and quard and install it with new one , reinstalling the new umbrella fitted inside the pan by making a new one and removing the old one , replacement ribbon arm of the mascute receiving crystallizer , making new separator of a centrifugal machine , removing the wornout truff of the hopper and installing it with new one , making and installing new separators for continuous centrifugal machines , removing the tubes of quad juice heater and dynamic juice heater and expanding them by installing new tubes and giving their hydraulic testing satisfactory of size 42 mm , removing the tubes of pan installing new tubes and expanding them and giving hydraulic tesing with satisfactory trial of size 96 mm , removing the wornout flue gas ducting of both the boilers and installing it with newone making from new or old plates , removing the wornout front and roof plate at boiler number 1 and 2 and installing with a new plate , removing the damaged boiler damper and installing a new one , making bagasse suit and installing. , replacement of juice over flow box of clarifier , making and installing bed of motor and pumps at various places as per requirement , replacement 6 inch dia cooling pipe of sulfur furnace , removing the monitor casing of a machine from old machine and installing it and giving its a trial , making amd replacing manholes at various places , making and replacing the enternals of cather of the pan. , making and replacing the new hood of cane cutter , removing the old bottom plate of the lowest compartment of the clarifier and placing a new plate on it after placing an angle trap as per the instructions and giving a satisfactory water trial , reinstalling the stirrer of the clarifier and giving a satisfactory trial , removing the shaft of a pug mill and replacing the old bushes on both sides and fitting new ones , removing and refitting the shaft of a brown sugar magma mixer and installing with new bush , reinstalling the trufff of connecting rod of the hopper , making and installing new catcher strainer , removing the old rail line of the trolley of the unloader and fitting the new rail line satisfactorily and doing water level , reinstalling the old rail line of the unloader s bridge and fitting it and checking water level etc , removal of old and weak channels of 3 inches to 10 inches diameter installed at various places and installation of new ones as per requirement , cutting and straightening old plates installed at various places as per requirement , removal of old and wornout scrubber installed on sulfur furnace and making and replacing with 8 or 10 mm plate and making all the connections , removing the trufff plate including support corroded shell and top cover plate of the top chamber of the clarifier and fitting the new plate and giving it s a water proof trial , re-installation alignment and //bid details 2 / 47 trial of hopper driving end , making and installing the top cover of the centrifugal machine , making an arm and installing it on the shaft of pug mill , making and installing scrubber and bottle jackets of
Tender For auction sale of others - cond. different types of m&p items consisting of 1] sc. power pack, petrol driven engine [hrd], make- lukas, qty-1 no, 2] sc. control desk, make- lukas, qty-1 no, 3] sc. re railing bridge 1.1 mtr height 184 mm, make- lukas, qty-1 no, 4] sc. telescopic jack hp 65/t 400r, make- lukas, qty-4 nos, 5] sc. telescopic jack hp 25/t 450r, make- lukas, qty-4 nos, 6] sc. claw jack hp 50/p 850r, make- lukas, qty-3 nos, 7] sc. holding wire rope, make- na, qty-5 nos, 8] sc. inflatable tower light m/c 3.5 hp, make- aska, qty-2 nos, 9] sc. power pack 8.3 hp, diesel driven [hre], make- greaves ltd., qty-2 nos, 10] sc. portable generator set petrol/kerosene driven ,1.5 kva , make- greaves ltd., qty-6 nos, 11] sc. re-railing bridge 2.2 mtr, make- lukas, qty-1 no, 12] sc. re-railing ramp [ci] , make- na, qty-2 nos, 13] sc. pulling device,cap-220 kn, make- lukas, qty-1 no, 14] sc. jack 65/t small, make- lukas, qty-1 no, 15] sc. jack lukas 100 kn single act dia 60 mm, make- lukas, qty-1 no, 16] sc. jack 25/t 185 r [small], make- lukas, qty-2 nos, 17] sc. jack 65/t [big], make- lukas, qty-2 nos, 18] sc. rail grip for axle pusher, make- lukas, qty-1 no, 19] sc. hydraulic jack [manual] 10/t-2 nos & 30/t-1 no, make- na, qty-3 nos, 20] sc. hose pipe rubber, make- na, qty-11 pairs, 21] sc. cutter lukas [hrd], make- lukas, qty-1 no, 22] sc. spreader with spare nose, make- lukas, qty-1 no, 23] sc. combo cutter lukas, make- lukas, qty-1 no, 24] sc. base of jack 25/t , make- lukas, qty-1 no, 25] sc. base of claw jack, make- lukas, qty-2 nos, 26] sc. line closure for pulling device , make- lukas, qty-2 nos, 27] sc. axle pusher head , make- lukas, qty-4 nos, 28] sc. claw jack head , make- lukas, qty-4 nos, 29] sc. height piece for [radious plate] telescopic jack [ai] , make- lukas, qty-2 set, 30] sc. claw jack rope head , make- lukas, qty-4 nos, 31] sc. bridge stopper[triangular shape] , make- lukas, qty-3 nos, 32] sc. roller carriage , make- lukas, qty-3 nos, 33] sc. roller carriage top plate , make- lukas, qty-2 nos and 34] sc. portable diesel generator set , make- greaves ltd., qty-1 no. condition- 1. lot will be delivered as per qty mentioned in description column, 2. materials like nearby other machine and ferrous , nonferrous , ss items etc near/surrounding the offered items is not allowed for lifting or taking delivery and the same is required to be handed over to the custodian if so found, 2. picking and choosing of materials near the offered items is not allowed.3. purchaser has to make his own arrangement for lifting and taking delivery of the lot.4. custodian may allow purchaser to bring crane if it is required and justified.5. the lot will be sold on "as is where is basis", 5. cutting/dismantling of sold lot is allowed.
Tender For supply of bathroom water shower (v2),copper alloy taps/stop valves (v2) conforming to is 8931,copper alloy taps/stop valves (v2) conforming to is 8931,copper alloy taps/stop valves (v2) conforming to is 8931,bathroom water shower (v2),stainless steel sinks for domestic purposes (v3) as per is 13983,copper alloy taps/stop valves (v2) conforming to is 8931,bathroom beveled edge looking mirror incl pvc almn frame size 2 fit into 2 fit,pvc low level flushing cistren dual function 10 ltr cap,pvc float valve 20mm with rod and ball,towel rack 24 inch,pvc syphone kit for low level flushing cistern 10 ltr cap,hand wash basin ovel type 450 into 300mm,pvc cabinet mirror for bath room size 450mm into 350mm,cp towel rail 600mm,glass corner shelves,hydraulic door closer universal 45 to 60 kgs,road patch mate 20kg bag,speed braker 750mm into 250mm into 75mm
Tender For auction sale of depot miscellaneous scrap - ubl/gsd/c-0035/elecrical/25/k [pl no.98411019] condemned and un-serviceable electrical scrap consisting of rail cutting machines, portable rail drilling machines, rail grinding machines, air/blower tank, rail trimmers, abrasive cutting machines, generators, hydraulic track lifting device with/without ms/ss/nfs attachment, their its parts and other similar scrap. available under the custody of cdms/rs ward/gsd/ubl. note: bidder has to physically inspect the lot before bidding. location:- road no 2 gsd/ubl bin no- block- c-035. remarks-. delivery should start from one end. no pick and choose allowed