Tender For nib for supply of hardware - super senior pellet mill, bearing cover frontforged steel, bearing cover rearforged steel, bearing setting ringforged steel, counter shaft assembly with pulley without beltwithout bearing & pedestal, die cover ringforged steel, die holder (steel) forgedforged steel, die holder assemblyforged steel, die holder rind rearsuitable for above alloy steel, die holder ring frontforged steel, feeder conditioner s. s. knifes.s. 304, thread 1/2" bolt per piece, feeder conditioner screw and paddle type feeder conditioner body s.s. approx. 1430 mm long s.s. -304 construction arrangement of single drive feeding end., front bearing spacer for t shaft, front scraper (roll stay assembly)forged steel with clamping stay, front scraper blades for pellet mill, pellet cooler air lockheight 450 mm/width 250 mm inlet/outlet 155 mm, pellet cooler eccentric assembly, pellet cooler sensor, pellet diesize:520 dia inner x 635 outer x 23.0 wider pellet :10/8 mm hole perforationmounting: tapper collar 12 deg on 620.6 dia or straight plug dia 610 diafixing 12-m 20 x 25 deep on 565 pcdmaterial: en 19c or 42crmo4 duly hardened & temp. polished, rc4=5, pulley assembly (fly wheel) 11 grooveforged steel, rear scraperforged steel, roll holder shaft (t shaft) assemblyforged steel, shearing pin, helical gear with hubone set containing 2 numbers, helical gear without hubone set containing 2 numbers, pellet mill sieve, screw for variable speed feeder conditioner for pellet mill, shear pin holding body, shear pun bush, spring set, teflon bush for main t shaft, pallet down spout, roll stay support stud (ss), pedestal sn 617, pedestal sn 619, pedestal sn 615, press roll assembly super senior, bearing cover, bearing retainer/nut for eccentric shaft km- 20, center bolt/roller stud (allen, bolt, head type design), circlip(dia 180 inside), clamping device tension ring(90x101x17) mm , distance ring, eccentric shaft, lock nut with lock washer for press roll eccentric shaft, lock washer (mb-20), nut for center bolt (lighting ring), press roll assembly complete with shell, bearing etc.suitable for above en-24 shell, press roll shell, setting ring, spacer (sealing ring), molasses mixer, molasses cutting knife with nutsuitable for above ni, hard duly balanced, paddle plane and loop typesuitable for above ni, hard duly balanced, spray pipe nozzle with nipple1.5 inch c class pipe, 3/8 inch nipple, mixer pipe (ss) suitable for molasses mixer, full circle hammer mill, beater (flat type) all equal weight, (big size 180 mm x 50 mm x 10 mm)ni hard, dynamically balanced, beater (flat type) all equal weight, (small size 140 mm x 47 mm x 06 mm), beater holder shaften, material, beater holding bush (size length 30 mm, in dia 20 mm, outer dia 30 mm), beater holding bush (size length 60 mm, in dia 20 mm, outer dia 30 mm), beater holding bush (size length 36 mm, in dia 20 mm, outer dia 30 mm), beater holding bush (size length 53 mm, in dia 20 mm, outer dia 30 mm), carrying rod for hammer mill 2 no of each set, door closing clamp set, hammer mill feeder, permanent magnet, sieve set3 mm, thick ms sheet with 3 mm, 2mm, 4mm, 5mm and 6mm perforations, sieve set clamping frame, hammer mill rotor, screw conveyor, screw conveyor, gravity pipe clamping 8 inch dia., gravity pipe clamping for above pipe8 inch dia, 16 gauge., gravity pipe m.s.8 inch dia, 16 gauge, 1 meter long, gravity pipe s.s.8 inch dia. 14 guage 1 mtr. long., pazama flap 3 way for distributionsuitable for 8 inch pipe, screw of different sizes, shaft suitable for joining the screw conveyor, chain conveyor, radler chain matching our existing chain conveyor. chain should 10mm thick links along with bushes and roller duly hardened., chain supporter with single bearing $nylon roller with shaft and bearing 1 no., lock ring, shaft 255mm long, chain supporter with double bearing $nylon roller with shaft and bearing 2 no., lock ring, shaft 255mm long, chain supporter (3-piece bush) $nylon roller without beari
Tender For bid to ras tender for supply of axial fan external rotor motor - axial fan- external rotor motor mechanical characteristics motor type - single phase induction motor bearing type - maintenance free ball bearing blade material - crca/steel with powder coated fan guard - ms with powder coated basket grill type direction of rotation - sucking-counter clockwise ip protection - ip-44 or better balancing grade - fan conform 6.3 grade as recommended by is1940-1-2003 or better surface of rotor - aluminium alloy dimensions - fan blade od- 300 +/- 5 mm grill mounting pcd- 360 +/- 5 mm electrical characteristics voltage - 230vac 50hz power consumption - 85 w or better insulation class - class f motor protection - thermally protected electrical leads - terminal box performance characteristics speed - 1350 rpm or better air flow - 960 cfm or better noise level - 60 dba or better protection class - i product conforming to standard - iec 60034 iec 60335 , axial fan- external rotor motor mechanical characteristics motor type - single phase induction motor bearing type - maintenance free ball bearing blade material - crca/steel with powder coated fan guard - ms with powder coated basket grill type direction of rotation - sucking-counter clockwise ip protection - ip-44 or better balancing grade - fan conform 6.3 grade as recommended by is1940-1-2003 or better surface of rotor - aluminium alloy dimensions - fan blade od- 350 +/- 5 mm grill mounting pcd- 420 +/- 5 mm electrical characteristics voltage - 230 vac 50hz power consumption - 140 w or better insulation class - class f motor protection - thermally protected electrical leads - terminal box performance characteristics speed - 1380 rpm or better air flow - 1500 cfm or better noise level - 58 dba or better protection class - i product conforming to standard - iec 60034 iec 60335 , axial fan- external rotor motor mechanical characteristics motor type - single phase induction motor bearing type - maintenance free ball bearing blade material - crca/steel with powder coated fan guard - ms with powder coated basket grill type direction of rotation - sucking-counter clockwise ip protection - ip-54 or better balancing grade - fan conform 6.3 grade as recommended by is1940-1-2003 or better surface of rotor - aluminium alloy dimensions - fan blade od- 400 +/- 5 mm grill mounting pcd- 470 +/- 5 mm electrical characteristics voltage - 230vac 50hz power consumption - 180 w or better insulation class - class f motor protection - thermally protected electrical leads - terminal box performance characteristics speed - 1380 rpm or better air flow - 2354 cfm or better noise level - 65 dba or better protection class - i product conforming to standard - iec 60034 iec 60335 , axial fan- external rotor motor mechanical characteristics motor type - three phase induction motor bearing type - maintenance free ball bearing blade material - crca/steel with powder coated fan guard - ms with powder coated basket grill type direction of rotation - sucking-counter clockwise ip protection - ip-54 or better balancing grade - fan conform 6.3 grade as recommended by is1940-1-2003 or better surface of rotor - aluminium alloy dimensions - fan blade od- 450 +/- 5 mm grill mounting pcd- 520 +/- 5 mm electrical characteristics voltage - 415vac 50hz power consumption - 138 w or better insulation class - class f motor protection - thermally protected electrical leads - terminal box performance characteristics speed - 920 rpm or better air flow - 2223 cfm or better noise level - 66 dba or better protection class - i product conforming to standard - iec 60034 iec 60335 , axial fan- external rotor motor mechanical characteristics motor type - three phase induction motor bearing type - maintenance free ball bearing blade material - crca/steel with powder coated axial fan- external rotor motor mechanical characteristics motor type - three phase induction motor bearing type - maintenance free ball bearing blade material - crca/steel with
Tender For supply of sugar bag stitching machine spares - bag stitching machine head and spares, servicing of sugar bag stiching machine & installed in this mill (rates to be quoted per day inclusive of to & fro fare etc.), spares for sugar bag stiching machine modle no. sdt/mt of st 500 installed in kichha sugar company, 062013 crank connecting rod, 062031 arm shaft crank (rear), 3/16 s 28017, 9/32 s 28014, 3/8 n 28214, 073021 looper carrier rod head complete, 065262 tension dise. complete, needel gb 250, v-belt a/34, v-belt a/35, foot switch complete, s.s.counter sunk screw with lock nut 1 1/4" x 1/4", slate for beg conveyer mats complete with brass roller in place of pvc roller, bearing no. 6205, bearing no. 6305, oil seal 35x56x10, oil seal 25x40x10, spocket 7 teeth bore 1", spocket 16 teeth bore 1", spocket 16 teeth bore 32 mm, cycle chain of head-up chain, split pin for roller 3/32 x3/4, 061031 lopper shaftbushing (rear), 062021 stud screw for 062013 with nut, 062291 pressure foot lifting lever, 062321 stud screw for 062291, 062301 pressure foot lifting hanger, 062311 spring for 062291, 11/64 s40001 screw for above, 11/64 s40005 screw for above, 065171 tension regulating nut, 9/64 s40042 screw for side plate, knife set (lower and upper), 065384 cutter eccentric assembly, spares for sugar bag stiching machine installed in kichha sugar company model no. special 80000 dx, feed dog 80037, throat plate 80036, preser foot 80035, needel bar 80057 & 80058 (l + r), needle gb 250 long size, looper st 26 x, looper carrier rod head, needle bar with nut ha 56, needle lever ball link 80084, looper side plate, spring for presser foot lifting lever, screw and nut, bolt 10nos, cutter ecentrie assembly, tension disc complete, tension regulating nut, redecon gear complite, motor for stitching machine, moter for conveyer mats
Tender For tender for supply of vehicle repair tata yodha - cluth cylinder assy kit , air filter set , fuel water separtor , element kit oil filter , brake lining , split pin , pilot bearing ms , ring synchroniser , counter shaft cluster gear , water pump tata for tata yodha , liquid gasket , universal joint , oil seal , release bearing assy , ball bearing , oil pressure switch for tata yodda , tie rod drag link right and left , castrol steering oil premium plus , tata genuine coolant , engine oil premium plus , m and l for testing for replacement of side mirror with frame 01 job , m and l for wheel balancing and alignment checking adjustment of wheel bearing including refitting wheels inluding weight charges complete each job 01 , m and l for replacement of fornt and back complete set of seat cover superior quality as approved by mto 01 job , repair to fuel system cleaning servicing and calibration of fip system 01 job , greasing and cleaning to be carried out after completion of all above mentioned work and testing to seen the veh satisfactorily condition