Latest butt fusion fittings Tenders | Government butt fusion fittings Tenders

State Government

CTN :41256107

04 Aug, 2025 4.95 Lacs

Jaipur - Rajasthan

Tender For supply of cid joints for hdpe pipe long collar sub division kotputli

State Government

CTN :41256108

04 Aug, 2025 4.95 Lacs

Jaipur - Rajasthan

Tender For supply of cid joints for hdpe pipe long collar sub division virat nagar

CTN :41195936

13 Aug, 2025 NA

Pithoragarh - Uttarakhand

Tender For supply of will be 600 x 450 mm with powder coated aluminium frame , sun shade a sun shades 900 x 300 mm for ventilators , sun shade b sun shades 1215 x 550 mm for main doors , self tapping screw 4 inch , self tapping screw 3 inch , rivet full size , nut bolt of size 12mm dia 75mm long with washer , nut bolt of size 12mm dia 125mm long with washer , nut bolt of size 12mm dia 150mm long with washer , 20w led tube light fiting with electronic ballasts and bipin holder and connector and block and etc complete with all accessories , bulk head fitting with 8w short body cfl , modular pvc square box 4 x 4 inch , angle holder , led bulb 15 watt , mcb box 2 way spn , mcb 10 to 32 amp sp , modular switch socket combine 5 oblique 15 amp , star screw full thread 25mm each packet 100 , change over switch 32 amp , tape insulation one and half x 15 mtr with isi mark , wire single core copper conductor 1 point 5 sqmm , elect wire two core copper conductor 6 sqmm , modular switch piano and flush type 5 amp , modular pvc switch board 6x4 inch , ceiling rose , pvc casing and capping of size 25mm , pvc casing and capping of size 25 mm tee , pvc casing and capping of size 25 mm elbow , pvc casing and capping of size 25 mm common for joints , flexible pipe 25mm , lightening conductor made of copper tube 1500mm long x 25mm dia with five copper prongs of length 150mm each fixed to copper ball of dia 50mm and 4mm thick with securing arrangement , solar street light 25w including pole having length 5 mtr long and 75mm dia and complete accessories warranty for street lighting system including battery min 2 years , vitreous china squatting pan iwc orissa pattern and size 680 x 470 mm white with integral foot rests and complete fixing arrangement including vitreous china valveless , vitreous china wash hand basin pedestal type angle back white and flat back and pedestal pype size 580 mm x 450 mm including bracket and pvc connections and waste pipe and 15mm bore cp pillar taps , vitreous china bowl urinal flat back size of 465 mm x 355 mm x265mm white including bracket and waste pipe and urinal spreader with pvc connections and connection pipe , p trap 100mm dia for wc of isi mark , pvc pipe 110 mm dia , pvc y oblique t junction 110mm dia , pvc socket 110 mm dia , pvc swr bend plain 110mm dia , ppr pipe pn 16 oblique sdr 7 point 4 and 3 layer 20mm , ppr pipe pn 16 oblique sdr 7point 4 and 3 layer 32 mm dia , ppr reducer 32 x 20mm outer dia , ppr reducer tee 32 x 20mm outer , ppr union 32mm dia , ppr socket 32mm dia , ppr tee 32mm outer , ppr elbow 32mm isi mark , ppr end cap 32mm dia , ppr socket 20mm dia , ppr elbow 20mm , ppr t 20mm outer dia , pvc floor trap 3 inch dia , pvc pipe 3 inch dia , pvc elbow 75mm dia , pvc t 75mm dia , ppr tank connector inner dia 32mm , ppr gate valve 32mm outer dia , bathroom cabinet ptmt cabinet with looking mirror for toiletry items of size 330mm x 140mm x 530mm with arrangements to fix the same with wall , sealing thread , ppr female threaded elbow inner dia 20mm , ppr female threaded socket dia 20mm , ppr female threaded tee inner dia 20mm , pvc connection pipe 2 feet long with 2 brass nut and bolt , pvc door bend 110mm dia outer dia , pvc tee 110mm dia , m seal , pvc gel 100ml each , taplone tape , ppr wall clamp dia 25mm , ppr wall clamp dia 32mm , cp bib cock 15mm bore long body , cp angle valve chromium plated steel 15 mm bore , cp stop valve chromium plated steel 15 mm bore , cp pillar tap 15 mm bore , ss soap dish holder , cp towel rail 24 mm dia and 600 mm long with fixing fixing arrangement , pre fabricated //bid details 2 / 75 ms angle 65 x 65 x 5mm with cross bracing between all the four sides of ms angle 40x50x5mm staging for frp tank 500ltr as per tech specs and drg attached , hdpe oblique pvc water tank 500 ltrs and triple layer and including float valve and accessories , cgi sheet 3000 x 900mm x 0 point 60mm of isi mark , gi pipe 2400mm long and 50 mm dia and 1 point 5mm thick , field water heating devices

State Government

CTN :41230030

05 Aug, 2025 7.00 Lacs

Bikaner - Rajasthan

Tender For procurement of various sizes c.i. detachable joints for hdpe pipe at divisional store of distt rural div i bikaner

CTN :41177763

30 Jul, 2025 NA

Mumbai - Maharashtra

Tender For supplying items for the new integrated high court complex at bandra government colony, cts no. 629/1234/a, bandra (east), mumbai. - all concrete should be admixed with integral hydrophilic crystalline admixture (16bars) reputed makes like bulwark. taskmek, grace or equivalent for reducin permeability by more than 85% when tested as per din 1048 part 5 (after applying cycles of hydrostatic pressure), for self-healing of cracks up to a width of 0.40 mm, for reduced sulphate attack and for high early strength of concrete etc. this should meet the requirements specified in the recommended dosage rate of 1% complete as per manufacturers specifications to the entire satisfaction of engineer-in-charge. hydrophilic crystalline admixture shall also have a corrosion inhibitant property and shall be compatible with any other water reducing concrete chemical admixtures added to concrete for workability purpose. crystalline formation shall be mix of cylindrical & circular in shape to have maximum filling of pores the admixture used shall have manufacturers test reports and approval mandatorily both from iits and irc (indian road congress). approved makes: pidilite/ technonicol/ myk/ mapei, providing & applying 2 components, solvent free, liquid applied elastomeric seamless hybrid polyurea polyurethane membrane, using high pressure plural component spray equipment, to form a minimum system thickness of 1.5 mm in two or more passes with a total consumption of 1.5-1.6 kg / m2. the membrane shall have 100% solids, voc free, tensile strength > 15 mpa as per astm d 412, elongation > 450% as per astm d 412, low temperature crack bridging ability of 3.2mm as per astm c 1305, shore a hardness > 85 astm d 2240, puncture resistance > 1000 n as per astm e 154, water head resistance > 7 bar as per astm d 5385.the coating should pass dynamic crack bridging as per en 1062-7, method b for 20,000 cycles at -20 degree temperature. the membrane shall exhibit 25 years of service life tested and complied in accordance with en 13251:2016 durability certification. apply primer coat of epoxy primer by roller/ airless spray guideline and coverage @ 5-6 m2/ltr depends on porosity of concrete. allow to cure for max 5-6 hours. broadcast anti slip grains of 200-300 micron (dried sand) on wet primer at coverage of 0.8-1 kg/m2 and allow to come to touch dry condition before application of membrane. approved makes: pidilite/ technonicol/ myk/ mapei, supplying and installing 1.5 mm composite thick fully bonded weldable hdpe membrane conforming to is 16471:2017 requirements of ug waterproofing structures, requirements to provide type a fully bonded protection of ug waterproofing structures. the membrane shall exhibit 25 years of service life tested and complied in accordance with en 13251:2016 durability certification. the membrane should be minimum 2.4 m wide comprising of an hdpe layer and a pressure sensitive adhesive layer which is covered by a weatherproof protective layer with lap joint strength at overlaps >15000 n/m astm d 6392:2012. the membrane shall have minimum of 100 mm side and end laps which shall be thermos fused with leister machines at all the joints for assuring watertightness and achieving monolithic membrane. end laps and side laps should be a minimum of 100 mm with double weld system, comprising of two parallel welds of 15 mm wide each with a 20 mm air channel gap in between the two weld lines. the size of the membrane should not be less than 2.4 mtr. x 20 mtr. to minimize the joints. this membrane shall be continued over the vertical surface but terminated minimum 100mm below the top edge of the raft slab/footings and fixed as per recommendation. the hdpe membrane should have the below mentioned technical properties- 1) lap joint(side and end lap) strength at overlaps 15000 n/m astm d 1876 2) resist hydrostatic pressure of 70 m head of water as per astm d5385 3) puncture resistance of 1000 n as per astm e1544) peel adhesion to concrete of 150

Central Government/Public Sector

CTN :41201870

31 Jul, 2025 NA

Pune - Maharashtra

Tender For hdpe plastic tarpoline with stitching eye hooks of size 24 feet x 21 feet (cut size 23 feet x 19 feet) 200 gsm made from closely woven hdpe fabric & laminated with virgin quality hdpe joints & border h eat sealed to made it 100% waterproof borders hemmed & provided with rope all around with eyelets fixed at distance of 6 feet colour or blue make trishul or similar. (sample will be approved by consignee before b ulk supply) [ warranty period: 30 months after the date of delivery ]

State Government

CTN :41160073

31 Jul, 2025 1.50 Lacs

Rajsamand - Rajasthan

Tender For supply of cid joints for hdpe pipe 110 mm at div store rajsamand

State Government

CTN :41160079

31 Jul, 2025 1.50 Lacs

Rajsamand - Rajasthan

Tender For supply of cid joints for hdpe pipe 90mm at div store rajsamand

State Government

CTN :41143620

28 Jul, 2025 30.00 Lacs

Didwana - Rajasthan

Tender For procurement of cid joints used with hdpe pipes conforming to is 8794 amended revised up to date

CTN :41043092

28 Jul, 2025 5.88 Lacs

Thiruvananthapuram - Kerala

Tender For one panchayath one playground - development of ground in sathyan nagar estate ward in nemom lac, thiruvananthapuram - supply and installation of outdoor gym equipment - gym equipments (18% gst), od40855/2025-2026 : horse rider - supply and installation of horse rider having the following specifications: dimensions: (l x w x h) 1140 x 400 x 1400 mm. main frame - 114 mm od b class gi pipe. foundation plate m.s. round plate of 250 mm & 8 mm thick. foundation cover cap -dome shape of pp / nylon / hdpe material. remaining frame is made by 48 mm od b class gi pipe. seat frame is madeby 48 mm od b class gi pipe. seat position must be horizontal to 110 -120 degree. link - made up of 48 mm od b class g.i. pipe. angle between link and ground position is 10-20 degree. handle - 33 mm od b class gi pipe. paddle vertical support - 60 mm od b class gi pipe. handle frame- 42 mm od b class gi pipe dually bending design. foot pipe - 33 mm od b class gi pipe. support frame 10 mm thick ms flat is used. seat- dimension 320 x 270 x 100 mm blow moulded wall thickness 4mm material hdpe. bearing bush closing cap pp /nylon / hdpe material. foundation stool: made from main pipe 88 mm od m.s pipe and top support of m.s. round plate of 250 mm & 8 mm thickness is welded at top. square tube of 30 x 30 x 2 mm must be used to support center pipe. height of stool is 3 ft. foundation stool is embedded in c.c. stock below ground level. bearing - use is 6005 permanent lubricated reputed brand. bearing bushes - 60mm od seamless pipe. pin made of 25 mm m.s. bright bar. grips - high quality rubber 46 mm od. circlips a 24 circlips are used for assembly. coating - best quality of powder coating 60 to 70 micron. safety instructions and exercise chart - start & finish position stick on product. all joints must be welded as per is standards and zinc primer paint should be applied at all the welding points prior to finishing., od40856/2025-2026 : back extension - supply and installation of back extension having the following specifications: dimensions: (l x w x h) 1060 x 730 x 990 mm. main frame - made from 88 mm od b class g.i. pipe. foundation plate m.s. round plate of 250 mm & 8 mm thick. leg support - 42 mm od b g.i pipe. seat rest pipe 42 mm od b class g.i pipe. handle pipe 33 mm od b class g.i pipe. footrest - cast iron 124 x 296 x 5 mm thick and m.s plate of 3 mm thick used to support it. footrest pipe 42 mm od b class g.i pipe and 80 x 40 mm ms rectangular pipe. closing cap pp / nylon / hdpe material. seat 360 x 300 x 2 mm thick m.s. seat with corner fillet for safety. grips - high quality rubber 46 mm od. foundation stool: made from main pipe 88 mm od m.s pipe and top support of m.s. round plate of 250 mm & 8 mm thickness is welded top. square tube of 30 x 30 x 2 mm must be used to support center pipe. height of stool is 3 ft. foundation stool is embedded in c.c. stock below ground level. coating - best quality of powder coating 80-120 micron. safety instructions and exercise chart - start & finish position stick on product. all joints must be welded as per is standards and zinc primer paint should be applied at all the welding points prior to finishing, od40857/2025-2026 : sky walker - supply and installation of sky walker having the following specifications: dimensions: (l x w x h) 1720 x 910 x 1700 mm. main frame - made of 88 mm od b class gi pipe dually bending design. foundation plate m.s. round plate of 250 mm & 8 mm thick. paddle vertical support - 42 mm od b class gi pipe. handle - 33 mm od b class gi pipe dually bending design. leg movement frame 50 mm x 50 mm x 2 mm thick square pipe. footrest - cast iron 124 x 296 x 5 mm thick and m.s. plate of 2 mm thick use for to support it. top closing cap dome shape made by pp / nylon / hdpe material. closing caps pp / nylon / hdpe material. foundation stool: made from main pipe 88 mm m.s pipe. and top support of m.s. round plate of 250 mm &a

Butt Fusion Fittings Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

State Government

State Government

State Government

Central Government/Public Sector

State Government

State Government

State Government