Latest cluster coating Tenders | Government cluster coating Tenders

Central Government And Public Sector

CTN :41118414

01 Aug, 2025 NA

Nagpur - Maharashtra

Tender For corrigendum : supply of channel below ramp for raised trough floor under frame as per drg: rdso/cg/drg/21009 ite m no 18. (one set consists of 08 nos. of channels). item to be supplied with red oxide zinc chromate primer coating. [ warranty period: 30 months after the date of delivery ]

CTN :41011385

05 Aug, 2025 NA

East Khasi Hills - Meghalaya

Tender For corrigendum : supply of cp bib tap 15 mm , app based polymer membrance 1 mm thick , cp soap dish , pvc low level flushing cistern10 ltr capacity dual flush , cp pillar tap15 mm , cp stop cock 15mm , cp health faucet with hook and 1 point 5m long tube , cp angle stop cock 15mm , cp centre hole wash basin mixture hot and cold 15mm , mirror looking l 600 mm and w 450mm with frame , cp bip tap 15mm 2 way double hand with flange , pvc seat cover white for anglo indian type wc , cp towel ring , gun metal gate valve brass 20mm , pvc float valve with rod and ball 20mm , cp bib cock long body 15mm , stainless steel kitchen plate rack size l30 inch w 30 inch and dia10 inch , stainless steel kitchen plate rack size l 30 inch w 24 inch and dia 10 inch , pvc connection pipe 15 mm dia 600 mm long with two nos coupling , stainless steel kitchen sink with single bowl l 24 and w 18 , gun metal gate valve brass 15 mm dia , pvc connection pipe 15mm dia 450mm long , pvc angle stop cock 15mm dia , pvc bip cock 15mm short body , synthetic enamel paint black colour , aluminium floor door stopper double , primer red oxide , paint og green , bend pipe pvc 32mm dia for low level flushing cistern , synthetic enemelled paint grey , sharpi flood light 280 watt , led water proofed focus dj light 200 watt , enamel, synthetic, exterior (a) under coating (b) finishing paint (v3) confirming to is 2932 (q3)

CTN :41224323

01 Sep, 2025 NA

Gorakhpur - Haryana

Tender For supply of cross member complete for lhb coaches as per drg no 2 10113.0.03.131.003, material conf irming to irs: m-41/97. to be supplied with red oxide zinc chromate primer coating [ warranty period: 30 months after the date of delivery ]

CTN :41224349

01 Sep, 2025 NA

Gorakhpur - Haryana

Tender For supply of cross member complete for lhb coaches as per drg no 2 10113.0.03.131.002, material conf irming to irs: m-41/97. to be supplied with red oxide zinc chromate primer coating [ warranty period: 30 months after the date of delivery ]

CTN :40827948

04 Aug, 2025 NA

Thane - Maharashtra

Tender For corrigendum : procurement of pipeline coating material for bpcl pipeline locations - cold tape inner wrap wr washala , cold tape outer wrap wr washala , primer wr washala , mastic filler wr washala , coating wrapping machine wr washala , cold tape inner wrap wr gujri , cold tape outer wrap wr gujri , primer wr gujri , mastic filler wr gujri , coating wrapping machine wr gujri , cold tape inner wrap cr kota , cold tape outer wrap cr kota , primer cr kota , mastic filler cr kota , coating wrapping machine cr kota , cold tape inner wrap cr bina incl bppl complete , cold tape outer wrap cr bina incl bppl complete , primer cr bina incl bppl complete , masticfiller crbina incl bppl complete , cold tape inner wrap vbplvadinar , cold tape outer wrap vbplvadinar , primer vbplvadinar , masticfiller vbplvadinar , coatingwrapping machine vbplvadinar , cold tape inner wrap sr kochi incl khpl complete , cold tape outer wrap sr kochi incl khpl complete , primer sr kochi incl khpl complete , masticfiller sr kochi incl khpl complete , coatingwrapping machine sr kochi incl khpl complete , cold tape inner wrap nrpiyala , cold tape outer wrap nrpiyala , primer nrpiyala , masticfiller nrpiyala , coatingwrapping machine nrpiyala

Central Government And Public Sector

CTN :41224704

14 Aug, 2025 NA

Nagpur - Maharashtra

Tender For supply of set of boxing on sole bar for automobile carrier coach with side entry. consists of (i) end bo xing on sole bar rh as per rdso drg. no. rdso/cg/drg/ 21009, item no. 13, qty. 02 nos./set. (ii) end boxi ng on sole bar lh as per rdso drg. no. rdso/cg/drg/ 21009, item no. 14, qty. 02 nos./set. (iii) middle bo xing on sole bar as per rdso drg. no. rdso/cg/drg/ 21009, item no. 15, qty. 02 nos./set. one set consist of three types of boxing, total qty. 6 nos. note:- middle boxing item no. 15 of drg. no. rdso/cg/drg/ 210 09, to be supplied in pieces of length 2396 mm. (12 pieces per set) and without slots. items to be supplied with red oxide zinc chromate primer coating. [ warranty period: 30 months after the date of delivery ]

CTN :41224352

02 Sep, 2025 NA

Gorakhpur - Haryana

Tender For supply of set of members 1 no lhs & 1 no rhs as per drawing no 2 10113.0.03.130.101 & 2 10113.0. 03.130.102 respectively made of irsm-41:97 with red oxide zinc chromate primer coating [ warranty pe riod: 30 months after the date of delivery ]

CTN :41177763

30 Jul, 2025 NA

Mumbai - Maharashtra

Tender For supplying items for the new integrated high court complex at bandra government colony, cts no. 629/1234/a, bandra (east), mumbai. - all concrete should be admixed with integral hydrophilic crystalline admixture (16bars) reputed makes like bulwark. taskmek, grace or equivalent for reducin permeability by more than 85% when tested as per din 1048 part 5 (after applying cycles of hydrostatic pressure), for self-healing of cracks up to a width of 0.40 mm, for reduced sulphate attack and for high early strength of concrete etc. this should meet the requirements specified in the recommended dosage rate of 1% complete as per manufacturers specifications to the entire satisfaction of engineer-in-charge. hydrophilic crystalline admixture shall also have a corrosion inhibitant property and shall be compatible with any other water reducing concrete chemical admixtures added to concrete for workability purpose. crystalline formation shall be mix of cylindrical & circular in shape to have maximum filling of pores the admixture used shall have manufacturers test reports and approval mandatorily both from iits and irc (indian road congress). approved makes: pidilite/ technonicol/ myk/ mapei, providing & applying 2 components, solvent free, liquid applied elastomeric seamless hybrid polyurea polyurethane membrane, using high pressure plural component spray equipment, to form a minimum system thickness of 1.5 mm in two or more passes with a total consumption of 1.5-1.6 kg / m2. the membrane shall have 100% solids, voc free, tensile strength > 15 mpa as per astm d 412, elongation > 450% as per astm d 412, low temperature crack bridging ability of 3.2mm as per astm c 1305, shore a hardness > 85 astm d 2240, puncture resistance > 1000 n as per astm e 154, water head resistance > 7 bar as per astm d 5385.the coating should pass dynamic crack bridging as per en 1062-7, method b for 20,000 cycles at -20 degree temperature. the membrane shall exhibit 25 years of service life tested and complied in accordance with en 13251:2016 durability certification. apply primer coat of epoxy primer by roller/ airless spray guideline and coverage @ 5-6 m2/ltr depends on porosity of concrete. allow to cure for max 5-6 hours. broadcast anti slip grains of 200-300 micron (dried sand) on wet primer at coverage of 0.8-1 kg/m2 and allow to come to touch dry condition before application of membrane. approved makes: pidilite/ technonicol/ myk/ mapei, supplying and installing 1.5 mm composite thick fully bonded weldable hdpe membrane conforming to is 16471:2017 requirements of ug waterproofing structures, requirements to provide type a fully bonded protection of ug waterproofing structures. the membrane shall exhibit 25 years of service life tested and complied in accordance with en 13251:2016 durability certification. the membrane should be minimum 2.4 m wide comprising of an hdpe layer and a pressure sensitive adhesive layer which is covered by a weatherproof protective layer with lap joint strength at overlaps >15000 n/m astm d 6392:2012. the membrane shall have minimum of 100 mm side and end laps which shall be thermos fused with leister machines at all the joints for assuring watertightness and achieving monolithic membrane. end laps and side laps should be a minimum of 100 mm with double weld system, comprising of two parallel welds of 15 mm wide each with a 20 mm air channel gap in between the two weld lines. the size of the membrane should not be less than 2.4 mtr. x 20 mtr. to minimize the joints. this membrane shall be continued over the vertical surface but terminated minimum 100mm below the top edge of the raft slab/footings and fixed as per recommendation. the hdpe membrane should have the below mentioned technical properties- 1) lap joint(side and end lap) strength at overlaps 15000 n/m astm d 1876 2) resist hydrostatic pressure of 70 m head of water as per astm d5385 3) puncture resistance of 1000 n as per astm e1544) peel adhesion to concrete of 150

CTN :41166612

29 Jul, 2025 31.53 Crore

Patna - Bihar

Tender For rrsmp/25-26 barsoi/05 - bangali tola to pmgsy road, clearing and grubbing road land (by manual means)clearing and grubbing road land including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300 mm, removal of stumps of such trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, upto a lead of 1000 m including removal and disposal of top organic soil not exceeding 150 mm in thickness as per technical specification clause 201., scarifying existing bituminous surfacescarifying the existing bituminous road surface to a depth of 150 mm and disposal of scarified material with a lift upto 3 m and lead upto 1000 m as per technical specification clause 301.4., construction of subgrade & earthen shoulderconstruction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table 300.2 with lead upto 1000 m as per technical specification clause 303.1., granular sub-base with well graded material (table 400.1)construction of granular sub-base by providing well graded material (crushed stone aggregates and local sand), spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at omc, and compacting with three wheel 80-100 kn static roller capacity to achieve the desired density, complete as per technical specification clause 401, ( by mix in place method ) for grading ii material, wbm grading 3providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kn in stages to proper grade and camber, applying and brooming, stone screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density grading 3 as per technical specification clause 405., a (by manual means ), prime coat (low porosity)providing and applying primer coat with bitumen emulsion (ss-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0kg/sqm using mechanical means as per technical specification clause 502, tack coatproviding and applying tack coat with bitumen emulsion (rs-1) using emulsion distributor at the rate of 0.25-0.30kg per sqm on the prepared granular surfaces treated with primer & cleaned with hydraulic broom as per technical specification clause 503., tack coatproviding and applying tack coat with bitumen emulsion (rs-1) using emulsion distributor at the rate of 0.20 to 0.25 kg per sqm on the prepared bituminous surface cleaned with hydraulic broom as per technical specification clause 503., patch work over wbm using mix seal surface for bituminous and existing cc pavementproviding, laying and rolling of close-graded premix surfacing material of 20 mm thickness composed of 13.2 mm to 0.9 mm (type-a) or 13.2 mm to 0.9 mm (type-b) aggregates using penetration grade bitumen (i.e. 92% of standard bitumen and 8% waste processsed plastic by weight shall be used for coating aggregate after its heating) as per irc:sp:98-2013, to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 8-10 kn static roller and finishing to required level and grades as per technical specification clause 509., semi-dense bituminous concreteproviding and laying semi dense bituminous concrete with 100-120 tph batch type hmp producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 4.5 to 5 per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, ro

Central Government And Public Sector

CTN :41146724

11 Aug, 2025 NA

Surat - Gujarat

Tender For supply of two component self priming surface epoxy primer gray shade as per attached technical specifications , two component high solids acrylic aliphatic polyurethane finish coating color shade as per is-5- eau-de-nil 216 as per attached technical specifications , two component high solids acrylic aliphatic polyurethane finish of color shade as per is-5-french blue shade 166 as per attached technical specifications , two component high solids acrylic aliphatic polyurethane finish of color shade as per is-5-a.c.grey shade 693 asper attached technical specifications , epoxy thinner compatible for surface tolerant epoxy primer coating , pu thinner compatible for acrylic aliphatic polyurethane finish coating , two component, high build, high solids heavy duty coal tar epoxy coating with good abrasion and corrosion resistance for internal lining of sea water pipes as per attached technical specifications , epoxy thinner compatible to heavy duty coal tar epoxy coating , water based rust converter of marine grade as per following technical specifications

Cluster Coating Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

Central Government And Public Sector

Central Government And Public Sector

Central Government And Public Sector