Latest coal mill scrap Tenders | Government coal mill scrap Tenders

corporations/Associations/Others

CTN :41532482

26 Aug, 2025 NA

Perambalur - Tamil Nadu

Tender For auction sale of cane preparation unit_1 lot rate per lot,mills, top roller , feed bottom roller and discharge roller_1 lot rate per lot,pumps, mill pump, feed pump_1 lot rate per lot,power turbine 1 and power turbine 2_1 lot rate per lot,diesel generator engines_1 lot rate per lot

Corporations And Associations And Others

CTN :41521524

08 Sep, 2025 NA

Ajnala - Punjab

Tender For mill roller shaft bloom

CTN :41516685

08 Sep, 2025 NA

Salem - Tamil Nadu

Tender For mtps- ii â mill plant division â reconditioning of pin bolt, pin bolt inserting bore of the roller tyre holding yoke frame assembly, roller tyre rtd cover plate, worn out surface of loading frame assembly, hydraulic shaft tension rods, renewal of worn out coal pipes, dismantling of flanges from old coal pipes & welded with new coal pipes, collar seating worn out portion of 90ë & 90ë+ 65ë coal bends, hard facing of dia 600 mm old coal bend, worn out seal cover seating distance spool piece flanges, fabrication & replacement of worn out deflector cone and coal feeding centre pipe (partial length) at inner side of classifier assembly etcâ¦ in coal mill â f/h

CTN :41516686

08 Sep, 2025 NA

Salem - Tamil Nadu

Tender For mtps- ii â mill plant division â reconditioning of pin bolt, pin bolt inserting bore of the roller tyre holding yoke frame assembly, roller tyre rtd cover plate, worn out surface of loading frame assembly, hydraulic shaft tension rods, renewal of worn out coal pipes, dismantling of flanges from old coal pipes & welded with new coal pipes, collar seating worn out portion of 90ë & 90ë+ 65ë coal bends, hard facing of dia 600 mm old coal bend, worn out seal cover seating distance spool piece flanges, fabrication & replacement of worn out deflector cone and coal feeding centre pipe (partial length) at inner side of classifier assembly etcâ¦ in coal mill â a.

Central Government/Public Sector

CTN :41487100

09 Sep, 2025 NA

Bokaro - Jharkhand

Tender For supply of requirement of roller tyre for pan mill

Central Government/Public Sector

CTN :41516669

09 Sep, 2025 NA

Multi City - Multi State

Tender For requirement of roller tyre for pan mill

State Government

CTN :41140874

25 Aug, 2025 3.19 Lacs

Sarni - Madhya Pradesh

Tender For corrigendum : procurement of oil seal wear ring for roller journal shaft of bhel make coal mill xrp-903 of unit 10 and 11 stps, sarni. mppgcl

CTN :41473557

30 Aug, 2025 45.00 Lacs

Bikaner - Rajasthan

Tender For nib for supply of hardware - super senior pellet mill, bearing cover frontforged steel, bearing cover rearforged steel, bearing setting ringforged steel, counter shaft assembly with pulley without beltwithout bearing & pedestal, die cover ringforged steel, die holder (steel) forgedforged steel, die holder assemblyforged steel, die holder rind rearsuitable for above alloy steel, die holder ring frontforged steel, feeder conditioner s. s. knifes.s. 304, thread 1/2" bolt per piece, feeder conditioner screw and paddle type feeder conditioner body s.s. approx. 1430 mm long s.s. -304 construction arrangement of single drive feeding end., front bearing spacer for t shaft, front scraper (roll stay assembly)forged steel with clamping stay, front scraper blades for pellet mill, pellet cooler air lockheight 450 mm/width 250 mm inlet/outlet 155 mm, pellet cooler eccentric assembly, pellet cooler sensor, pellet diesize:520 dia inner x 635 outer x 23.0 wider pellet :10/8 mm hole perforationmounting: tapper collar 12 deg on 620.6 dia or straight plug dia 610 diafixing 12-m 20 x 25 deep on 565 pcdmaterial: en 19c or 42crmo4 duly hardened & temp. polished, rc4=5, pulley assembly (fly wheel) 11 grooveforged steel, rear scraperforged steel, roll holder shaft (t shaft) assemblyforged steel, shearing pin, helical gear with hubone set containing 2 numbers, helical gear without hubone set containing 2 numbers, pellet mill sieve, screw for variable speed feeder conditioner for pellet mill, shear pin holding body, shear pun bush, spring set, teflon bush for main t shaft, pallet down spout, roll stay support stud (ss), pedestal sn 617, pedestal sn 619, pedestal sn 615, press roll assembly super senior, bearing cover, bearing retainer/nut for eccentric shaft km- 20, center bolt/roller stud (allen, bolt, head type design), circlip(dia 180 inside), clamping device tension ring(90x101x17) mm , distance ring, eccentric shaft, lock nut with lock washer for press roll eccentric shaft, lock washer (mb-20), nut for center bolt (lighting ring), press roll assembly complete with shell, bearing etc.suitable for above en-24 shell, press roll shell, setting ring, spacer (sealing ring), molasses mixer, molasses cutting knife with nutsuitable for above ni, hard duly balanced, paddle plane and loop typesuitable for above ni, hard duly balanced, spray pipe nozzle with nipple1.5 inch c class pipe, 3/8 inch nipple, mixer pipe (ss) suitable for molasses mixer, full circle hammer mill, beater (flat type) all equal weight, (big size 180 mm x 50 mm x 10 mm)ni hard, dynamically balanced, beater (flat type) all equal weight, (small size 140 mm x 47 mm x 06 mm), beater holder shaften, material, beater holding bush (size length 30 mm, in dia 20 mm, outer dia 30 mm), beater holding bush (size length 60 mm, in dia 20 mm, outer dia 30 mm), beater holding bush (size length 36 mm, in dia 20 mm, outer dia 30 mm), beater holding bush (size length 53 mm, in dia 20 mm, outer dia 30 mm), carrying rod for hammer mill 2 no of each set, door closing clamp set, hammer mill feeder, permanent magnet, sieve set3 mm, thick ms sheet with 3 mm, 2mm, 4mm, 5mm and 6mm perforations, sieve set clamping frame, hammer mill rotor, screw conveyor, screw conveyor, gravity pipe clamping 8 inch dia., gravity pipe clamping for above pipe8 inch dia, 16 gauge., gravity pipe m.s.8 inch dia, 16 gauge, 1 meter long, gravity pipe s.s.8 inch dia. 14 guage 1 mtr. long., pazama flap 3 way for distributionsuitable for 8 inch pipe, screw of different sizes, shaft suitable for joining the screw conveyor, chain conveyor, radler chain matching our existing chain conveyor. chain should 10mm thick links along with bushes and roller duly hardened., chain supporter with single bearing $nylon roller with shaft and bearing 1 no., lock ring, shaft 255mm long, chain supporter with double bearing $nylon roller with shaft and bearing 2 no., lock ring, shaft 255mm long, chain supporter (3-piece bush) $nylon roller without beari

CTN :41435759

20 Aug, 2025 NA

Salem - Tamil Nadu

Tender For mtps- ii â mill plant division â repositioning of dislocated roller tyre shaft in yoke frame of mill after removing the broken body thread bolts in any 4 nos of roller tyre assembly of coal.