Tender For supply of black , copper wire 4 sqmm polycab red , copper wire 4 sqmm polycab yellow , copper wire 4 sqmm polycab blue , copper wire 4 sqmm polycab black , copper wire 16 sqmm polycab red , copper wire 16 sqmm polycab yellow , copper wire 16 sqmm polycab blue , copper wire 16 sqmm polycab black , copper wire 16 sqmm polycab green , copper cable 3cx2 5sqmm polycab , copper cable 4cx2 5sqmm polycab , copper cable 4cx4 sqmm polycab , copper cable 7cx2 5 sqmm polycab , shrinkable sleeve 2 5sqmm r y b bk , shrinkable sleeve 4 sqmm r y b bk , shrinkable sleeve 10sqmm r y b bk , shrinkable sleeve 16sqmm r y b bk , shrinkable sleeve 25sqmm r y b bk , shrinkable sleeve 35sqmm r y b bk , shrinkable sleeve 25sqmm green , elmex terminal connector cst 2 5 sqmm , elmex terminal connector cst 10 sqmm , elmex terminal connector cst 16 sqmm , elmex terminal connector cst 32 sqmm , elmex terminal connector cst 70 sqmm , elmex terminal connector cst 100 sqmm , terminal connector channel , mcb channel , star delta timer , single phase preventer 415v siemens , kaycee type 15260 on off switch , lug 1 5mm2 ring type copper packet , lug 2 5mm2 ring type copper packet , lug 4 mm2 ring type copper packet , lug 6 mm2 ring type copper packet , lug 10 mm2 ring type copper packet , lug 25 mm2 ring type copper packet , lug 16 mm2 ring type copper packet , lug 50 mm2 ring type copper , lug 70 mm2 ring type copper , lug 95 mm2 ring type copper , lug 120 mm2 ring type copper , lug 150 mm2 ring type copper , lug 400 mm2 ring type aluminium , lug 300 mm2 ring type aluminium , lug 150 mm2 ring type aluminium , copper lug pin type 1 5 sqmm packet , copper lug pin type 2 5 sqmm packet , copper lug pin type 4 sqmm packet , copper lug u type 1 5 sqmm packet , copper lug u type 2 5 sqmm packet , copper lug u type 4 sqmm packet , copper lug u type 10 sqmm packet , 240 vac indication led lamp red , 240 vac indication led lamp green , 240 vac indication led lamp yellow , 240 vac indication led lamp black , supply of dc 2 26 crc 1 box 400g , emery paper 0 number , emery paper 50 number , led bulb 6w , contactor 415v coil 230v mo 110 l and t , contactor 415v coil 230v mo 140 l and t , contactor 415v coil 230v mo 18 l and t , contactor 415v coil 230v mo 32 l and t , contactor 415v coil 230v mnx 80 l and t , contactor 415v coil 230v 3tf49 siemens , contactor 415v coil 230v 3tf47 siemens , contactor 415v coil 230v ml 1 5 l and t , contactor 415v coil 230v ml 4 l and t , contactor 415v coil 230v mnx32 l and t , contactor 415v coil 230v mnx25 l and t , overload relay mo type 4 6 6 7a l and t , overload relay mo type 6 7 9 7 a l and t , overload relay mo type 8 5 12 5 a l and t , overload relay mn type 4 6 7 5a l and t , overload relay mn type 1 4 2 3 a l and t , overload relay mn type 6 10 a l and t , overload relay mn type 9 15 a l and t , overload relay ml type 4 6 5 a l and t , overload relay ml type 6 10 a l and t , overload relay ml type 30 50 a l and t , overload relay mn type 4 5 6 5a l and t , flp gland et type 15mm 3 4 sudhir , flp gland et type 17mm 3 4 sudhir , flp gland et type 22mm 1 inch sudhir , flp gland et type 19mm 3 4 sudhir , flp gland m20 type 15mm 3 4 sudhir , flp gland m20 type 17mm 3 4 sudhir , flp gland m20 type 19mm 3 4 sudhir , smps , //bid details 2 / 133 ammeter 0 10a , flp wp push button station stop reverse sudhir fcg , flp wp push button station stop forward reverse sudhir fcg , cable joint kit 3cx25mm2 , cable joint kit 4cx2 5mm2 , cable joint kit 3cx16mm2 , cable joint kit 3cx35mm2 , battery terminal , petroleum jelly , flp break glass switch , flp esd switch , flp switch on off , flp hooter , earth flat 25 x 3 mm , earth flat 50 x 6 mm , 36 w led tube havells , 18 w led tube havells , led flood light 300w non flp , street pole light 150 w , led light 90w flp , led light 100w flp , led flood light 150 w , pt 415 110v , nightstick xpr 5522gmx flp torch sudhir , cable tie 100 mm packet , cable tie 150 mm packet , cable tie 300 mm packet , copper
Tender For corrigendum : supply and execution items for reliability improvement of signalling inst. section of sr. dste/1/lko of lucknow div. nr. - excavating and refilling of trench to the level of ground with rammed earth asper drg. no.(nr/s&t/con/1.1/97a) so as not to form a drain 0.3 mtrs wide & 1mtr deep on both side of the station along side the track. it shall confirm to the safe distance as per signalling and cable plan in all type of soil, it also includes clearence of roots of trees and bushes., excavating and refilling of trench 0.3 mtrs wide & 0.8 mtr deep on pitced/stone/bricks paved surface, road/crossing/platform etc. and restoration of surafce to original condition., laying of signalling/telecom/power cables of different sizes as per attached guidelines (drg. no.(nr/s&t/con/1.1/97a) or latest on signalling cable laying and as per cable route plan approved by railways through trenches, rcc pipe, dwc pipe, gi pipe etc and meggering of cable before and after its laying of all type of outdoor cables. contractor have to transport cable from any store of lko division to site carefully. meggering to be done for each drum separately. meggering sheets to be supplied and filled up by contractor and submitted to railways, as per instructions by consignee., supply and laying of 2nd class bricks in the trench and laying as per drg. no. (nr/s&t/con./1.1/97a) or latest and as per instruction of the site engineer., boring and trenchless cabling along with supply and insertion of hdpe/dwc self lubricated pipes as per rdso spec no. rdso/spn/204/2011 ver 1.1 or latest of 120mm nominal dia in the bore at the depth of 1.4 meter to 2.1 meter from formation level (level of earth below ballast) as per drawing and as directed by engineer incharge by trenchless technology for laying of signalling /telecom/power cable under track /culvert etc. cable laying covered separately. inspection-consignee for supply of dwc/hdpe pipe. the following required coupling arrangement should also be supplied: 1. suitable snap fit couplers withrubber o ring, 2. spacers, 3. tees. 4. bend. 5. end cap(1 no. =6mtr ,straigh tpipe). (a) the cost shall include horizontal boring through any intermediate obstruction, either natural or man made or any boundary etc. (b) the rate is inclusive of all the materials equipment and labour required for during trenchless horizontal boring under the railway track. nothing extra shall be admissible on any account than the rate quoted above. (c) the pipeis to be laid underrailway track/road /culvert. all necessary arrangement are to be provideand all precautions are to be end is not deviated from the horizontal level line by more than 250mm in horizontal and vertical direction. (d) the rate shall be inclusive of direction and protection of underground utilities encountered during boring. (e) the payment for boring shall be made only when dwc/hdpe pipe are laid in the bore., concreting unschduled items in concrete of 1:3:6 ratio in cement, coarse sand and aggregate 25mm at different places in the yard and plastering top in fine plaster of 1:4 cement sand ratio. it also includes the excavation of earth as required at site and as per instruction of site incharge. the volume in cubic metres shall include the volume occupied by any ci foundation, trestle, ms angle or flat or gi pipe required to be embedded in the casting. cement coarse sand and aggregate 25mm are to be supplied by the contractor., earth work for excavation and refilling around location boxes and signals etc. where necessary including 50m lead and 1.5m lift. the lead is to be measured from centre of gravity of location to the centre of filling and lift from main ground level. the earth work should be well rammed including breaking of clods, levelling and dressing etc. as per instruction of engineer at site., brick work with well burnt bricks in foundations and plinths with cement and sand (ordinary) mixture of 1:4 ratio. all material is to be supplied by th
Tender For (1)supply and installtion of chemical earth pit and laying of cable 250 meter for new vcb 1000 amp and supplying and making indoor and outdoor cable heat shinkabnle jointing at kc2 pit sub station (2)complete repairing of
Tender For bid to ras supply of plane table complete set as per isi specification consisting of board , vernier transit theodolite as per isi specification no 2988 1965 , alidade sight vane brass 24 , clinometer compass semi compass , magnetic trough compass in wooden case 15 cm , quick setting dumpy level complete with stand , telescopic alidade in box with standard accessories , prismatic compass with ring divided in to complete with having stand ball , telescopic aluminum stand for prismatic compass , indian pattern clinometer tangent comp in case , abney level with slow motion 6 , box sextant pocket in leather case , levelling staff aluminum folding type 6 meter , floating globe dia 16 cms with led light arc base self revolving leviating , celestial star globe with earth inside basic dia 30cms , 3d globe 2 in 1 globe light off physical world light , 3d raised relief maps 75 100 cms , liquid prismatic compass ms001 liquid prismatic compass mk iiia guaranteed , weather station fully assembled and well equipped weather kit , wind speed measurement range , multifunction digital altimeter altimeter barometer compass thermometer , solar system automatic revolving with cd ge020 cyber sky cd rom program , astronomical reflector telescope 76mm objective lens dia 675 telescope , 3d self framed very superior quality fibre glass models rock cycle model , 3d self framed very superior quality fibre glass models ocean feature , anerod barometer , sprit level , pantograph 60cm in box , weather report map polyart plastic geographical astronomical charts ) /bid number : gem/2026/b/7518201 * /dated: 14-05-2026 & & / bid document 1 / 32
Tender For supply of materials and erection for shifting of control room pannel at 33/ 11 kv sub station bharsawa distt. kaushambi under deposit scheme on "semi turnkey basis" under edc, kaushambi - name of work: supply, carriage & erection of materials for control room pannel shifting of shiffting of 33/11 kv s/s bharsawa distt. kaushambi, supply of de-centralised materials, 11 kv 3x120 mm2 xlpe cable jointing kit o/d & i/d, control cable 4x2.5 mm2, control cable 2x2.5 mm2, g.i. pipe 6 " dia, rubber matting, clamp with nut & bosts, earth wire clamp for pcc pole, stay clamp for pcc pole, top channel clamp pcc pole, dropper channel clamp pcc pole, g.i. strip 35x6 mm, carriage of following material, pcc pole 8.5 mtr. long., structure of la, 33kv isolator, 33 kv cts, single t/f control pannel, 33kv vcb,11 kv outgoing. incoming pannel, battery & battery charger and other associated accessiories etc. (availibility at concern store center of store division), erection work, installation of 33 kv single transformer control pannel 2 no., incoming 2 no. and 7 no. outgoing in the switchgear room and grouting the pannel by rag bolt using cement, sand mortar in ratio 1:3. work includs fitting of all accessories in all respect with complete connection of control cable with pannel. all material will be provided by the contractor except vcb and crp., construction of cable trenchs with top cover and laying of control cable for vcb, c.t. & t/f control pannel etc. as per direction of engineer. trenchs to be 12 wide and 9 deep. work includes digging, of trench, concreting of the foundation in the ratio 1:3:6 r.b. wall 9 wide with cement mortar 1:4 and plastering inside the trench in the ratio 1:3 and sand filling in the trench. all material will be provided by the contractor., earthing of 11 kv indoor equipments, switchgears as per resspo drawing. with g.i. strip of size 35x6 mm. g.i. strip fully welded at both ends and to be connected with earthmat,, erection of dp with pcc pole 8.5 mtr long with all accessaries and grouting of the pcc pole with cement, sand and brick ballast ratio 1:4:8 size 0.45x 0.45x 1.5 mtr deep under the ground as per drawing no. res-6.(cement, sand, brick, ballast shall be provided by the contractor.), installation of 24 volt battery and battery charger with cabinet in the switch gear room, by grouting base channel 100 x 50 x 6 x 1000mm. fixing of rag bolt., laying of 11 kv 3x300/3x185/ 3x120 sqmm. xlpe cable by digging 0.75 mtr. deep trench, putting layer of sand in the bottom, ramming it, laying of cable over it rmt and covering the cable from sides and top by laying bricks, finally covering the same by earth and levelling of the same, all the materials, except cable, will be pvovided by the contractor., fixing and termination of outdoor/ indoor heat shrinkable cable boxes of size 3 x300/3x185/3x120 sqmm. xlpe cable. boxes will be supplied by the contractor, sundries ( as per site requirement/emergency work), safe dismantling of 11 kv o/g pannel & received back to store, laying of weasel conductor with the help of aluminium roller by hanging three nos. on each support in a manner taking sufficient care to ensure safety of weasel conductor against rubbing on ground, precaution for safety of crops is also to be taken. the work includes jointing of conductor by providing jointing sleaves, stringing of conductor upto correct sag and binding of conductor with insulators on each support. all material shall be provided by contractor such as jointing sleeve binding wire, armour rod etc.
Tender For renovation and standardization of earth mat and earthing of bay equipment pertaining to 33kv feeders and 33kv ptr bay equipment at 132/33kv sub-station bapatla under rmi 2024-25 scheme.
Tender For corrigendum : stage contract for carrying out various electrical maintenance works including sitc, itc of various line materials and distribution substations and dismantling of existing deteriorated out lived electrical infrastructure for the year 2026-27 under th - supply, installation, testing and commissioning of 3-phase 25 kva distribution transformers with bimetallic terminal connectors energy level-2, (al wound ), and with lv cable box having detachable aluminium gland plate, supply, installation, testing and commissioning of, 3-phase 63 kva distribution transformers with bimetallic terminal connectors energy level-2, (al wound ), and with lv cable box having detachable aluminium gland plate, supply, installation, testing and commissioning of, 3-phase 100 kva distribution transformers with bimetallic terminal connectors energy level-2, (al wound ), and with lv cable box having detachable aluminium gland plate, supply, installation, testing and commissioning of, 3-phase 200 kva distribution transformers with bimetallic terminal connectors energy level-2, (al wound ), and with lv cable box having detachable aluminium gland plate, supply, installation, testing and commissioning of, 3-phase 250 kva distribution transformers with bimetallic terminal connectors energy level-2, (al wound ), and with lv cable box having detachable aluminium gland plate, sitc of 11 mtr long st poles 410, sp-56 including transportation, manual, mechanical carriage, delivery at site with pit excavation, refilling the pit with soil, boulders., sitc of 9 mtr long st poles 410, sp-33 including transportation, manual, mechanical carriage, delivery at site with pit excavation, refilling the pit with soil, boulders., sitc of 8 mtr long st poles 410, sp-15 including transportation, manual, mechanical carriage, delivery at site with pit excavation, refilling the pit with soil, boulders., sitc of 8 mtr long pcc poles including manual, mechanical carriage, excavation of pole pits with inscription of permenent marking on each pole "name of scheme-2019-20/xx" (xxx mean pole numbers say 01,02...) in white paint in backgound of green paint at conspicious place, providing & fixing of pole earthing as per rec standard as per j-1 (spiral earthing) drawing, supply,fixing of spike earthing rod 20mm 2,5 mtr long with gi strip (25x3)mm, supply and painting of each pole 1 coat red oxide paint and 2 coats of aluminium paint (@ 1 ltr/pole red oxide paint and 1 ltr/pole aluminium paint), providing, errection, testing & commissioning of channel cross arms, v-cross arms, sub-station channels & angle iron braces, transformer beltings, including back clamps for fixing cross arms etc fabricated out of galvanized iron of different sizes (rec standard) & to be fixed with gi nuts & bolts and washers., providing, errection, testing & commissioning of channel cross arms, v-cross arms, sub-station channels & angle iron braces, transformer beltings, including back clamps for fixing cross arms etc fabricated out of mild steel of different sizes (rec standard) & to be fixed with gi nuts & bolts and washers., providing & and fixing of 11 kv pin insulators (polymer) with pins ( 5 kn), providing & fixing of 11 kv, g.o ab switch , 3-phase, 200a (09 insulator post type) with arragement for pad locks & operating rod . the operating rod should be g.i pipe (b-class) of 25 mm dia of requisite length., providing & fixing of 11 kv horn, gap fuse 3-phase 100a, providing & fixing of 11kv link set 3-phase, 200 a (station type), sitc of 11kv isolator double break, 3-pole, 630 amps, horizontal mounting type , with earth switch, providing & fixing supply and installation of gapless surge arrestor,9 kv,10 ka, la with (polymer) housing, station type, providing & fixing of lt fuse set of suitable capacity for 63kva,100kva,200kva (as per tender drawing attached), providing & fixing of 11 kv disc insulators (polymer) complete with fitting( 4
Tender For tender for supply of equipment material, design, erection, testing commissioning for sop to pump house constructed at jakhota-i bohal khalsa under hpshiva project w.r.t. horticulture development block dehra in electrical section bharoli under esd 1 - supply part of lt line with aaac 7/3.15 (0.323 km), steel tubular poles 8 mtr. long with base plate, steel tubular poles 9 mtr. long with base plate, muff for steel tubular pole with concrete filling, aaac conductor 7/3.15, 55 sq. mm ( includes 3 conductor length and additional 1% sag (sag, jumpering and wastage)), lt ab cable [size 4x70+1x70+1x16 sq. mm] x 2 cable, pvc (1.1 kv, ai, un-armour 3.5 x 35 sq. mm, single continuous earth wire (g.i wire 8 swg), channel iron (75x40x4.8 mm), length 1.50 mtr + 0.2 mtr}, shackle insulator, d-iron, stay set complete, stay wire, earthing set lt complete in all respect, earth knob, half clamp, full clamp, nuts & bolts off sizes, spiral pvc spacer, aluminium paint, red oxide point, supply part of aug. of 63 kva to 100 kva distribution sub-station, aluminium thimble 120 sq mm, lt cable 3.5 core 120 sq. mm, chain link fencing, angle iron, gate etc. for transformer fencing, 3-ph, 4-wire trivector meter 200/5 a, erection part of lt line, erection charges & transportation charges complete in all respect of lt line, erection part of aug. of 63 kva to 100 kva dtr, erection charges & transportation charges complete in all respect of aug. of 11/0.4 kv, 63 to 100 kva dtr
Tender For tender for supply of equipment / material , design, erection, testing & commissioning for sop to civil hospital jawalamukhi by providing 11/0.4 kv, 400 kva dtr a/w 11 kv ht line in electrical section amb under esd hpsebl no-i jawalamukhi, ed jawalamukhi. - supply part of 11 kv ht line with aaac 7/3.81 (0.065 km), steel tubular poles 11 mtr. long with base plate, muff for steel tubular pole with concrete filling, aaac conductor 7/3.81, 80 sq. mm ( includes 3 conductor length and additional 1% sag (sag, jumpering and wastage)), single continuous earth wire (g.i wire 8 swg), cross-arm {channel iron (100x50x6 mm), length 1270 mm}, 11 kv pin insulators ( porcelain, 12 kv, 10 kn): 3 no. per pole structure, ai (50x50x6 mm), length 750 mm x2 no., x-bracing set -ms angle iron 50x50x6, length {2125 mmx2 no }, pole top bracket (100x50x6 mm), length 100 mm, ht stay set complete, stay wire, earthing set ht complete in all respect, eye hook for earth wire, barbed wire (rec sp f 3-1981), half clamp, full clamp, danger plate (250x200x1.6 mm), nuts & bolts off sizes, 11 kv g.o. switch, d.o fuse unit, aluminium paint, red oxide point, supply part of 11/0.4 kv 400 kva distribution sub-station, steel tubular poles 9 mtr. long, muffs with concerete filling, x-arm: [channel iron (100x50x6 mm), length : 2800 mm x 2 nos], ms angle iron (50x50x6 mm), length: 2800 mm x(1 nos for las), x-arm: [channel iron (75x40x6 mm), length : 2800 mm x 4 nos] for supporting do fuse unit & go switch, x-arm [channel iron (100x50x6 mm), length : 2800 mm x 2 nos for transformer bed, x-arm [channel iron (100x50x6 mm), length : 460 mm x 2 nos for supporting main channel of transformer, ms angle iron (50x50x6 mm), length : 2800 mm x 2 nos, ms angle iron 35x35x5 mm), length : 460 mm x 2 nos, ms angle iron 50x50x6 mm), length : 950 mm x 2 nos for bed knee bracing, ms angle iron (50x50x6 mm), length : 2800 mm x 2 nos for lt distribution box and go switch assembly, ms angle iron (50x50x6 mm), length : 450 mm x 1 nos for lt distribution box and go switch assembly, go switch handle supporting : [ channel iron (75x40x6 mm), length:460 mm, go ab switch unit (11kv, 400a, 25 ka ) triple pole o/d type, d.o fuse unit, surge arrester, 9 kv station class (porcelain type), discs insulator sets (comprising 1 no. disc: ^^(porcelain, bs, 12 kv, 90 kn) including dead end clamps etc.), stay set complete, stay wire, pipe earthing set, gi wire (6 swg) earth wire, half clamp (m.s. flat 50x6 mm), full clamp ( m.s flat 50x6 mm), nuts and bolts of various sizes (galvanised / coated), aluminium thimble 300 sq mm, copper thimble 95 sq mm, danger plate, barbed wire, lt cable 3.5 core 400 sq. mm, lt cable 3.5 core 70 sq. mm, aluminium paint., red oxide, transformer bed (civil work), chain link fencing, angle iron, gate etc. for transformer fencing, ct pt combined unit, energy meter (3-ph, 4-wire) dlms compliant 1000/5 a ct type for 400 kva dtr, pvc multistrand 2.5 sq mm copper wire, ms angle iron (50x50x6 mm) length 2800 mm x 4 nos., ms angle iron (50x50x6 mm) length 450 mm x 2 nos., erection part of 11 kv ht line, erection charges & transportation charges complete in all respect of 11 kv ht line, erection part of 400 kva dtr, erection charges & transportation charges complete in all respect of 11/0.4 kv, 400 kva dtr