Tender For spare parts for scania veh - connectingrodbearing udi84.00mm part no 279621, exhaust valve part no 1397521(232018), general overhaul kit part no 551459(550227)
Tender For supply of bearing clutch release , pressure plate , clutch plate , connectingrodbearing set , piston ring set , engine overhaul kit , valve set , belt timing , piston
Tender For supply of overhauling kit for dust bin blower, specification details : set of 12 spares of dust bin blower motor: 1) drive end flange, code no. 3fcu070600 = 1 no, 2) front bearing cap outer, p t. no.3fcw083400 = 1 no, 3) non drive end cover, pt. no.3fcu011900 = 1 no, 4) rear bearing cap out er, pt. no. 3fcw076300 = 1 no, 5) terminal box cover, pt. no.3fau012200 = 1 no, 6) terminal box, cod e no.3faw077400 = 1 no, 7) male connector asm, code no.4pea0114000 = 1 no, 8) female connector, code no.4pea0115000 = 1 no, 9) gasket top, code no.3rtw006700 = 1 no, 10) gasket bottom, code n o.3rtw006800 = 1 no, 11) v-ring, code no.3rtw115600 = 1 no, 12) key-7.9 x 7.9 x 57.2mm = 1 no. [ warranty period: 30 months after the date of delivery ]
Tender For corrigendum : supply of full finish with stress relieved casting of grease flinger-1 , full finish with stress relieved casting of grease flinger-2 , full finish with stress relieved casting of grease flinger-3 , full finished machined casting of inner brg cap-4 , full finished machined casting of inner brg cap-5 , full finish with stress relieved casting of outer bearing cap - 6 , full finish with stress relieved casting of outer bearing cap -7 , full finish with stress relieved casting of bearing housing -8 , full finish with stress relieved casting of bearing housing-9 , full finish with stress relived casting of bearing housing dia 200-10 , full finish with stress relived casting of inner bearing cap-11 , full finish with stress relieved casting of brg cover external-12
Tender For supply of spares - gasket fuel pump to crank case part no a 906 091 05 80 make deutz , gasket oil pan to cyl. crank case part no a 906 014 09 22 make deutz , gasket fuel pump part no a 906 091 07 80 make deutz , gasket turbo oil inlet part no a 002 997 92 71 make deutz , gasket turbo oil drain part no a 541 187 00 80 make deutz , sender unit part no a 004 153 42 28 make deutz , sender unit part no a 004 153 76 28 make deutz , sender unit part no a 004 153 02 28 make deutz , sender unit part no a 007 153 08 28 make deutz , cylinder head gasket part no a 906 016 14 20 make deutz , turbocharger part no 9020962099 make deutz , main bearing standard size part no 9260300740 make deutz , connectingrodbearing standard size part no 9260300060 make deutz , piston ring part no a 906 030 10 24 make deutz , piston ring part no a 906 030 02 24 make deutz
Tender For supply of outer bearing cap drg no 24028942008 , outer bearing cap drg no 24028942022 , outer bearing cap drg no 24028942085 , outer bearing cap drg no 34028940103 , outer bearing cap drg no 24028842011 , outer bearing cap drg no 24028942001 , outer bearing cap drg no 24028842025 , inner bearing cap drg no 24028942023 , inner bearing cap drg no 24028842008 , inner bearing cap drg no 34025542008 , inner bearing cap drg no 24028842010 , inner bearing cap drg no 24028942002 , inner bearing cap drg no 24028842026 , inner bearing cap drg no 24028842027 , inner bearing cap drg no 24028842017
Tender For supply and installation of open gym equipments under mlalads funds for various locations of parks in municipal corporation of delhi - supply & installation of open gym equipments under mlalads funds for various locations of parks in municipal corporation of delhi, seated puller /pull chair made from c class g.i pipe. dimensions: - 1900mm (length) x 740mm (width) x 1920mm. (height). safe area:- 1.2mtr x 3mtr. seated puller equipment made up of c class g.i. pipe of different nb.nb stands for nominal bore sizes i.e. internal diameter of pipe in millimeters. the center pipe is of 100nb made from c class g.i. pipe. bottom support is of m.s. round plate of dia 250 mm & 10mm thickness welded. all linkages are made up of 25nb c class g.i. pipe. the handle frame is of 32nb c class g.i. pipe. the seat frame is of 32nb c class g.i. pipe. to build structure bushes are used which are made from seamless pipe of 60mm o.d. and 5mm thickness as well as 60mm diameter solid bar bush used. the foundation used for fixing is a structure and made from center pipe of g.i. of 80 nb c class. welded with m.s. round plate of dia 250 mm & 10mm thick. main pipe supported with 25 mm x 25mm m.s. angles of 3 mm thickness and 20mm x 40mm crc square pipes of 3mm thickness. foundation cover closing cap is made from injection moulded plastic lldpe / hdpe. the seats and back rests are fitted on the outer frames are made up of m.s. sheet of size 330 mm x 300 mmx2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges.closing caps are made up of from injection moulded plastic lldpe / hdpe.pins used of diameter 25mm and 17mm are made up from sae 8620 bright material. the bearings used are of 6205 2rs1 and 6203 2rs1 permanent lubricated sealed bearing of reputed brand.high tensile steel with galvanized nuts & bolts are used for assembly.thecirclips used for assembly are of a16. the gym equipment shall be finished smooth with a primer coating of atleast 40 micron followed by epoxy based powder coating with polyster powder coating of at least 60 to 70 micron thickness using exonobel / berger make paints or its equivalent paints. the holding down/fixing of gym equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size), cross trainer /elliptical exerciserdimensions: - 1320mm (length) x 600mm (width) x 1750mm. (height). safe area: - 1.77 x 1.2mtr. cross trainer equipment made from c class g.i. pipe of different nb.nb stands for nominal bore sizes i.e. internal diameter of pipe in millimeters. the main frame pipes are of 80nb c class g.i. pipe with single bend pipe with 250mm radius. the bottom support of m.s. round plate of dia 250 mm & 10mm thick. the handle frame is made up of 25nb c class g.i. pipe. the foundation used for fixing is a structure and made from center pipe of g.i. of 80 nb c class welded with m.s. round plate of dia 250 mm & 10mm thick. main pipe supported with 25 mm x 25mm m.s. angles of 3 mm thickness and 20mm x 40mm crc square pipes of 3mm thickness. to build structure bushes are used which are made from m.s. seamless pipe of 60mm od with 5 mm thickness. the footrests are made from injection moulded plastic lldpe / hdpe. closing caps are made up of injection moulded plastic lldpe / hdpe. pins used of diameter 35mm, 25mm, and 17mm are made up from sae 8620 bright .the bearings used are of 6007 2rs1 62052rs1 and 62032rs1 permanent lubricated sealed bearing of reputed brand. high tensile steel with galvanized nuts and bolts are used for assembly. the gym equipment shall be finished smooth with a primer coating of atleast 40 micron followed by epoxy based powder coating with polyster powder coating of at least 60 to 70 micron thickness using exonobel / berger make paints or its equivalent paints. the holding down/fixing of gym equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse