Tender For supply of electrical and electronics enginerring lab equipments - symmetrical and unsymmetric al faults of transmission line , testing of hrc fuse aodmcb , overcurrent relay trainer , tbree phase air circuit breaker (acb) trainer , .differential relay trainer kit for transformer , generator protection relay trainer kit , dc servo position control trainer kit , ac servo position control trainer kit , stepper motoer , synchro transmitter receiver , ammetersmi type voltmeter mi type wattmeter single phaselthree phase three phase power factor meters automatic power factor controller low power factor wattmeter single phase lux meter digital/energy meter shunt multiplier current transformer potential transformer modelofmi mc, dynamomete rand induction itype meters lcrlq meter hand beld type soldering iron synchroscop e frequency clip-on meter electrical and electronics tools three phase squirrel cage induction motor (cut section model) 5hpthree phase ac slip ring induction motor trainer , dc shunt motor -alternator set , basic wiring tools , basic wiring tools , brushless dc motor trainer kit , dual power supply multimeter, lcr meter cathode ray, oscilloscope function generator, signal generator digitallc tester, analog ic tester smd soldering, equipment cables/con nectors, television set television set, projector maintenance kit, tools vacuum, cleaner/blower components, microwave test bench, klystron power supply, microwave test bench -x, vswr meter frequency meter, pin modulator dso dc regulated power, supply synchro transmitter and receiver trainer kit, servo motor on-off control kit,, temperature sensor pi controller kit,, temperature sensor po controller kit,, temperature sensor pid controller kit,, temperature sensor plc, digital multimeter routers, repeater hub, switch connecting cables and connectors network bridge, null modem cable, microcontroller, trainer kit, cro, stepper motor, 7-segment led, display, trainer board, trainer board, trainer board, microcontroller, board, sensors, digital multimeter, and micro-ammeters, dual channel cro, passive components, resistor, variable inductor, potentiometer, digital multimeter, true rms, multimeter, dual channel cro, dc regulated power, supply, scr, dc regulated power, supply, thyristor kit, resistive load,, resistive- inductive, load
Tender For manufacture, testing, supply and delivery of digital multimeter, clampon meter for measurement of leakage current , clampon meter for measurement of load current and 5kv digitalinsulationtester
Tender For supply of 5 kv digitalinsulationtester with digital and analogue display five test range 250 volt , 500 volt, 1000 volt, 2500 volt, 5000 volt. insulation test upto 10 t ohm. suitable for all insulation resistanve diag
Tender For corrigendum : procurement of testing equipment for all power houses at thc sirmour - digitalinsulationtesters (megger)range: 0-100/250/500/1000v, digitalinsulationtesters (megger)range: 0-100/250/500/5000v, digital multimeterfeatures:dc & ac voltage; ac & dc current; continuity & resistance ; capacitance and inductance; checking of diodes/ transistors, single phase variable voltage autotransformers: details of single phase auto transformer 15a rating -input: 220v ac 10%; output: 0 to 270 volts.rating: 15 amps, three phase variable voltage autotransformers: details of three phase auto transformer 15a rating -input: 415v ac 10%; output: 0 to 500 volts, 3 phases.rating: 15 amps., tong tester cum multi meter (digital) (clamp on meter for ac measurements) specification for 0-1000a ac digital tong tester (clamp on meter) - current range: 0 to 1000 a (with settings of 1/10/20/40/100 a/500a/1000a auto ranging); voltage range: 0 to 60/300/600 v ac; accuracy: 0.3% or better, tong tester cum multi meter (digital) (clamp on meter for dc measurements) specification for 0-300a dc digital tong tester (clamp on meter) - current range: 0 to 300a (with settings of 1/10/20/50/100 a/300a auto ranging) ; voltage range: 0 to 60/120/300 v dc.accuracy: 0.3% or better., tong tester cum multi meter (digital) (clamp on meter for ac/dc measurements) specification for 0-100a ac digital tong tester (clamp on meter) - current range: 0 to 100 a (with settings of 00-20ma/100ma/500ma/1a/10a/50a/100a auto ranging); voltage range: 0 to 60/300/600 v ac; accuracy: 0.3% or better, digital phase sequence indicator: dial size: 96x96mm (minimum) ; working voltage: 50 to 500v ac; frequency: 25 to 60 cycles., digital earth resistance clamp meter with leakage current measurement