Latest digital meter Tenders | Government digital meter Tenders

Central Government/Public Sector

CTN :45737681

06 Jul, 2026 NA

Godhra - Gujarat

Tender For supply and commissioning of 3kva on-line ups with 120 minutes battery back-up 72v system, mosfet-pwm with in-built isolation technology, input power ? single phase 160-260v ac 50hz, output voltage single phase 230v ac +/-1%, sine wave 50hz, minimum vah ? 9600, protection - ip21, smf-vrla battery as per is: jisc:8702 (part i, ii, iii) with rack, over voltage/ under voltage/ overload and short circuitprotection at ups output terminals, max thd - 3%, digital metering in ups for data, efficiency >90%, 20% overload limit for 10 minutes, max overshoot and under shoot of output rated voltage - 4, voltage regulation from no load to full load - 3%, minimum 1,2 mm thick ms sheet enclosure with duly painted. with typetest report, minimum warranty of machine 2 years, make: microtek/apc/luminous/nps/techser. [ warranty period: 30 months after the date of delivery ] ]

CTN :45551266

01 Jul, 2026 NA

Kharagpur - West Bengal

Tender For w acting for and on behalf of the president of india invites e-tenders against tender no e-73-dyceekgpw-cbc-26-27 closing date/time 01/07/2026 15:00 hrs. bidders will be able to submit their original/revisedbids upto closing date and time only. manual o ers are not allowed against this tender, and any such manual o erreceived shall be ignored.1. nit headername of workupgradation of cbc overhauling section and corrosion repair shop of wagonrepair shop, kharagpur workshop.bidding typenormal tendertender typeopenbidding systemsingle packet systemtender closing datetime01/07/2026 15:00date time of uploadingtender09/06/2026 16:38pre-bid conferencerequirednopre-bid conference datetimenot applicableadvertised value 2402108.76tendering section elegenbidding style single rate for tender bidding unitabove/below/parearnest money (rs.) 48100.00validity of offer ( days) 60tender doc. cost (rs.)0.00period of completion 18 monthscontract type works - general contract category expenditurebidding start date 17/06/2026are jv allowed to bid nonumber of jv memberallowed0are consortium allowedto bidnonumber of consortiummember allowed0ranking order for bidslowest to highest expenditure typecapital (works)2. schedules.no. itemcodeitem qtyqty unitunit ratebasic value escl.(%) amount biddingunitschedule () a-cost of supply of material for electrical work1712792.421a12.00numbers383500.00 767000.00 at par 767000.00description:- supply of incoming 1x 630a,4p, 50ka mdo type microprocessor based acb withipr1+ release & outgoing (i)2 x 320a,4p, 36ka thermal magnetic release with adjustable thermal &fixed magnetic mccb (ics=100%icu),(ii)2 x 200a,4p, 36ka thermal magnetic release withadjustable thermal & fixed magnetic mccb (ics=100%icu),(iii)4 x 100a,4p, 36ka thermal magneticrelease with adjustable thermal & fixed magnetic mccb (ics=100%icu) tted in lt panel box14swg crca sheet powder coated 4way cu busbar of suitable rating, indicator lamp, digitalmultifunction meter & all other accessories. mccb & acb make:- havellls/ lk/ schneider/siemens.2a210.00numbers 400.02 4000.20 at par 4000.20description:- supply of mcb metal enclosure 4 pole3a380.00numbers 413.00 33040.00 at par 33040.00description:- supply of pyramid insulator as per drawing4a470.00numbers 531.00 37170.00 at par 37170.00description:- supply of pin type insulators as per drawing.5a550.00numbers1121.00 56050.00 at par 56050.00description:- supply of gi-angle (40 x 40 x 06 mm) bracket 4 way with porcelain insulator as perdrawing suitable for overhead light.6a610.00numbers 248.98 2489.80 at par 2489.80description:- supply of mcb metal box 2 pole7a720.00numbers1323.96 26479.20 at par 26479.20description:- supply of 16/20/25a power unit (containing 4 module plate, starter, socket and plug)for ac unit.8a85.00numbers11434.20 57171.00 at par 57171.00description:- supply and testing of oscillating type bldc pedastal fan, 230 v,400 mm sweep,multi speed, remote/button controlled make- atomberg, havells, crompton, bajaj, usha, orient.9a9 150.00 metre1150.50 172575.00 at par 172575.00page 1 of 18run date/time: 09/06/2026 16:38:46kgp-workshop-electrical/south eastern rlytender documenttender no: e-73-dyceekgpw-cbc-26-27closing date/time: 01/07/2026 15:009description:- supply of hot dip galvanized 2mm thickness perforated cable tray of size 300 mmwidth and 50 mm height and complete accessories as per is, ie rules and site requirement10a10 50.00 metre 575.25 28762.50 at par 28762.50description:- supply of cable trays 2mm thickness size 100 x 50 mm gi, perforated (rmt) withcover complete and as per is, ie rules and site requirement.11a11 10.00numbers 180.54 1805.40 at par 1805.40description:- supply of combined switch socket box - 16 a, capton 5-in-1 combined switch andsocket with isi mark,as per is:3854 or latest12a122.00numbers34700.26 69400.52 at par 69400.52description:- supply of 4 pole mccb ,release range (80-200)a, breaking capacity 36 ka,microprocessor release with inbuilt earth pr

CTN :45738001

11 Jul, 2026 NA

Leh - Jammu And Kashmir

Tender For supply of inch l , micro meter changeable anvil 0 to150 mm , measuring tape steel 3000 mm , precision file square with handle 8 inch comma 2nd cut , precision file half round with handle 8 inch comma 2nd cut , set of hand tap , chest comma tool feet j feet , gauntlets prospective welder leather , brushes steel wire 32 mm , portable welding machine , launch into 431 pr03 with hdiii car or truck , mahindra garuda ii i smart diagnostic tool , jaltest by cajoli ottw off highway equipment diagnostic tool 12v plus 24v , jaltest by cajoli cv truck comma bus comma light commercial vehicle 12v plus 24v , garuda 2vc1 professional grade comma j2534 compliant diagnostic tool for tata cv bs3 comma bs4 comma bs6 , cummins diagnostic tool inline 7 , jcb e into cavator construction diagnostic scanner electronic service tool with diagnostic , banjo washer aluminium , cotton waste , anabond red , o clamp 10 mm , emery paper rough or fine , banjo belt , banjo union , hose pipe 10 mm fle into ible , m seal , araldite big 90 gm , wd 40 rust remover , o ring set o size , valve grinding stick , valve grinding past rough or smooth , battery lead positive and negative , battery terminal h by d positive , battery terminal h by d negative , battery led pb for pole , battery thimble h by d , welding rod , flu into for gas welding , gas welding brazing rod 2 point 5 mm into 450 brass , gas welding brazing rod 2 point 5 mm into 450 aluminum , hand gloves leather , shoes for welding , welding appron leather , electeric holder heavy duty 100 ampere , welding cable copper 28 point 59 mm , stainless steel welding tong , aceteylene regulator , o into ygen regulator , torch with nozzle , supreme high pressure gas welding blow pipe , hose aceteylene gas cly , hose o into ygen gas cly , welding cutter blade size 107 into 1 point 3 into 16 mm , injector stage 3 tool kit , torque wrench , torque wrench digital small , bearing puller , mech jack chassis 10 ton , hydraulic jack chassis 10 to 15 ton , bailey plate jack 3 to 4 ton , magnet stick , ultrasonic cleaner , e-star socket and bit socket set , oil drip tray pan , pneumatic transmission oil filling tool with adaptor , heavy duty socket , vice bench heavy duty , dc test lamp digital automatic circuit tester , stanley 94 to 181 comma 150 piece high quality multi tool kit comma containing spanner comma driver sockets bits comma wrenches , vice bench small size , gauge chisel 38 mm , firmer chisel 26 mm , mortise chiesel 12 mm , combination ston , claw hammer , jack planer , pincer , planer machine , portable rotter machine , side cutting paier , circular saw blade 6 inch three square engineer scrapper with handle 100mm, chisel cold flat 25 mm x 200 mm, chisel 6", 9", hammer engineer's ballpin 400 gm, gauge thickness feeler type 0.03 to 0.5 mm, plier circlip external straight nose, plier circlip internal straight nose, spark plug socket 16 mm, spark plug socket 21 mm, hexagon socket head 0.5 inch square drive 10 mm to 32 mm, master tool kit 150 pcs , recersible rachet 0.5 inch square drive 250 mm, torque wrench 0.5 inch square drive 200 mm, allen key long ball point 10 mm, pad lock, pop spanner 6 x 22 mm, pop spanner 15 x 41 mm, nose plier 8", cutting plier 12", adjustable 12', file flat 6", 12", half round file 6", 12", round file 6", 9", 12", star screw driver 6", 9", 12", oil filter remover, torx key t30, injector remover socket 19 mmfor tata 697 bs iii & 497 bs ii, needle file set r, t & p, hammer electrician 200 gm, clamp on multi meter, digital multi meter, continuity tester, hexagon socket head size 6 mm to 42 mm, spinner handle 0.5 inch square drive, //bid details 2 / 91

CTN :45717384

09 Jul, 2026 6.26 Lacs

Jaipur - Rajasthan

Tender For procurement of analog meter, digital meters, smps and transducer for protection control panels and dc system panels, ht switchgear panels and lt switchgear panels at 2x660mw, rrvunl, ssctps, suratgarh

CTN :45704816

06 Jul, 2026 NA

Leh - Jammu And Kashmir

Tender For supply of air comp nk air comp 01 head assy , air comp nk air comp 02 head gasket , air comp nk air comp 07 fuel pipe line , air comp nk air comp 08 single element pump , air comp nk air comp 09 fuel lifting pump , air comp nk air comp 10 over flow pipe , air comp nk air comp 11 injector assy , air comp nk air comp 12 air cleaner assy , mpt nk mpt 11 clutch plate , x3 nk 15kva 59 digital meter

State Government

CTN :45684098

24 Jul, 2026 4.72 Crore

Belgaum - Karnataka

Tender For tender for establishment of centre of excellence in electrical vehicle at vtu regional centres of muddenahalli, mysuru, kalaburgi and talakal - servo motor rotating arm, propeller fin, battery connector, jumper pin header, battery holder, cable usb, button cap large passive elements, button small passive elements, button large passive elements, potentiometer(10ko) passive elements, switch passive elements, capacitor(10uf) passive elements, capacitor(104) passive elements, resistor(10ko) passive elements, resistor(1ko) passive elements, resistor(220o) passive elements, big blue led active elements, big yellow led active elements, big green led active elements, big red led active elements, rgb led active elements, diode active elements 1n4001, diode active elements 1n4148, pnp transistor 8550 active elements, npn transistor(8050) active elements, relay active elements, active buzzer active elements, motor drivers, seven segment display, lcd display, dc motor, servo motor, m to m jumper wires, f to f jumper wires, m to f jumper wires, tilt sensor, ultrasonic sensor holder, light sensor, ultrasonic proximity sensors, analog temparature sensors, breadboards, uno board, tx/rx module, usb cable for stm32 board, stm32 discovery board, basic can bus protocol training system, elecetrical vehicle charging technology bench, multi mcu trainer kit (with banana plug-ins), power electronics pre-build kit, permanent magnet synchronous motor with regen, differential gear training model (ev auto), ev wiring and harness system mock layout (2-wheeler), four wheeler simulator pmsm / bldc motor kit, battery management system (bms) training module, belt pulley, female type 6 charging socket, front wheel axle, front wheel rim ( 12 inch), tubeless tyres, main stand, side stand, mid - drive chassis, switches ignition, horn, indicator, head light, cone-set, handle bar, t-stamp, fork, smart charger can, dc-dc converter, swing arm, vcu, brake sensors, display, wiring harness, throttle (re twistable), mid drive motor 3kw and pull belt, mcu 120a, battery 4kw nmc, cordless drill machine tools, tool kit trolley tools, pipe wrench tools, screwdriver 803 tools, taparia screw driver 863 200 tools, taparia philips s/d psc862250 tools, taparia screw driver 861 100 tools, installation tape tools, soldering gun tools, multimeter tools, hammer - 40mm nylon tools, hammer - 500g tools, chissel tools, socket set box 24pc tools, long circlip plier outer tools, long circlip plier inner tools, t spanner 14mm tools, t spanner 12mm tools, t spanner 10mm tools, t spanner 8mm tools, t spanner 7mm tools, connector - 902 tools, tester tools, nose plier tools, monkey plier tools, wise grip plier tools, cutting plier tools, wire cutter tools, screw driver 2 in 1 - 903ibt tools, ring spanner set tools, double end spanner set tools, t allen key 3,4,5,6 mm tools, l allen key set tools, regulated power supply, motor hall phase tester, continuity tester, helmet, clamp meter, taco meter, hall sensor, shaft drive motor, bldc motor (cut section), pmsm motor (cut section), four wheelar car, shaft drive 2w full vehicle naked, mid drive 2w full vehicle 1, hub drive 2w full vehicle 1, hub drive 2w full vehicle naked 1, mid drive 2w full vehicle, mid drive 2w full vehicle naked, hub drive 2w full vehicle, hub drive 2w full vehicle naked, lfp cells 3.2 v 100 ah, hot air blower, screw gauge, black 12 awg wire, red 12 awg wire, hly cells, chogori 4+2 female connector, chogori 4+2 male connector, crimper, iec female connector, iec male connector, anderson sb50, safety gloves, safety glasses, duct tape 55mm, filament tape 55mm, kapton tape 55mm, lead, cell holder 2x2 - 32650, cell holder 2x2 - 21700, cell holder 2x2 - 18650, nickel strip - 32650, nickel strip - 21700, nickel strip - 18650, lfp cells 3.2 v 6 ah - 32650, nmc cells 3.7 v 4 ah - 21700, nmc cells 3.7 v 2.5 ah - 18650, spot welding machine 1kva (pneumatic), active balancer 24s 10 amps, ir tester

State Government

CTN :45695199

10 Jul, 2026 4.99 Crore

Belgaum - Karnataka

Tender For tender for establishment of centre of excellence in electrical vehicle power train technologies at vtu regional centre, bengaluru - servo motor rotating arm e, propeller fin e, battery connector e, jumper pin header e, battery holder e, usb cable e, button cap (large)passive elements, button(small) passive elements, button(large)passive elements, potentiometer(10ko)passive elements, switchpassive elements, capacitor(10uf)passive elements, capacitor(104)passive elements, resistor(10ko)passive elements, resistor(1ko)passive elements, resistor(220o)passive elements, big blue led active elements e, big yellow led active elements e, big green led active elements e, big red led active elements e, rgb led active elements e, active elements 1n4001 diode, active elements 1n4148 diode, pnp transistor(8550) active elements, npn transistor(8050) active elements e, relay active elements e, active buzzer active elements ev, motor driver e, seven segment display e, lcd display e, dc motor e, servo motor e, jumper wires e, tx/rx module e, tilt sensor e, ultrasonic sensor holder e, light sensor e, ultrasonic proximity sensors e, analog temparature sensors e, breadboards e, uno board e, usb cable for stm32 board e, ecu board, stm32 discovery board e, battery cell making machine, integrated electronics workstation, pcb design equipment, dynamometer 2w, electrical vehicle motors and drives workbench, battery management system (bms) training module e, model-based development (mbd) real-time controller, power electronics training bench, off board charger control board, pe-pp control panels, pdi unit, dc converters, drive axles, wheel axles, foot throttle e, auxiliary battery, relay e, harness, wheels e, differential e, moter ev, bms e, vcu e, mcu e, on board charger, battery pack e, naked chassis, belt pulley e, female type 6 charging socket e, front wheel axle ev, front wheel rim ( 12 inch) e, tubeless tyres e, main stand ev, side stand ev, mid - drive chassis e, switches ignition, horn, indicator, head light ev, cone-set ev, handle bar ev, t-stamp ev, fork ev, smart charger can ev, dc dc converter ev, swing arm ev, vcu ev, brake sensors ev, display ev, wiring harness ev, throttle (re twistable) ev, mid drive motor 3kw and pull belt e, mcu 120a e, battery 4kw nmc ev, cordless drill machine tools ev, tool kit trolley tools e, pipe wrench tools e, screwdriver 803 tools e, taparia screw driver 863 200 tools ev, taparia philips s/d psc862250 tools ev, taparia screw driver 861 100 tools e, installation tape tools ev, soldering gun tools e, multimeter tools e, hammer - 40mm nylon tools ev, hammer - 500g tools ev, chissel tools ev, tools 24pc socket set box, long circlip plier outer tools ev, long circlip plier inner tools ev, t spanner 14mm tools ev, t spanner 12mm tools ev, t spanner 10mm tools e, t spanner 8mm tools ev, t spanner 7mm tools ev, connector - 902 tools ev, tester tools ev, nose plier tools ev, monkey plier tools e, wise grip plier tools e, cutting plier tools e, wire cutter tools e, screw driver 2 in 1 - 903ibt tools ev, ring spanner set tools ev, double end spanner set tools ev, t allen key 3,4,5,6 mm tools ev, l allen key set tools ev, motor hall phase tester ev, continuity tester ev, safety helmet, programmable mcu, clamp meter ev, taco meter ev, mid drive mcu, hub motor mcu, hall sensor ev, mid drive stator, hub drive stator, induction stator, bldc stator, mid drive rotor, hub drive rotor, induction rotor, bldc rotor, induction motor, brush motor, shaft drive motor ev, bldc motor, pmsm motor, ev 4w - car, ev 3w - auto ev, ev2w - shaft drive - full vehicle, ev 2w - hub drive full vehicle ev, ev 2w - mid drive - full vehicle ev, ev 2w - hub drive - full vehicle ev, ev 2w - mid drive - full vehicle, ev 2w - hub drive - full vehicle, eight channel 3 amps cdc cell grading machine, cells bolt, cell 3.2 v 100ah lfp, hot air blower ev, green 100mm insulation, clamp meter 0-600 amps, battery tester, bus bars, screw gauge ev, silicon black, bla

CTN :45672948

04 Jul, 2026 NA

Patiala - Punjab

Tender For supply of x3 nd 4730 003259 pipe high pressure without connection , x3 nd 5330 011595 gasket 15mm thick pilmoid , x2 nd 5930 001058 switch toggle , g2 3439 000087 rod welding iron cast super silicon , g2 3439 000097 rod welding copper 5 mm , h1 a 8010 000160 paint rfu finishing general service , x3 nd ixc gl 530 161 05 gasket cyl head , x3 ixc kr 37 067 010 v belt a68 , x3 nd ixc 86542 digital meter , x3 nd ixc gl 12517 fuel filter set , x3 ixc prk 1250 40l 03 pipe fuel , x3 ixc gl sk 6970 flexible pipe , h3 5530 000214 ply wood for general purpose , lv6 mt6 9330 000106 sheet cellular 37 mm

CTN :45699353

06 Jul, 2026 57.22 Lacs

Panchkula - Haryana

Tender For supply, installation, testing and commissioning of clamp-on type ultrasonic flowmeter, online continuous effluent monitoring system, programmable iot panel gsm/gprs, electromagnetic flow meter, open channel ultrasonic flowmeter and all accessories co

CTN :45693762

13 Jul, 2026 57.77 Lacs

Bhiwani - Haryana

Tender For supply erection commissioning of electrical mechanical equipment for dewatering of flood water from field area for village badesra outfall at rd 70600l of jui feeder - supply, erection & commissioning of 5 c/s axial flow water lubricated vertical pumps of 5 cs. discharge at 1440 rpm at static head of approx 8.0 mtr. with y body, including ms bend including flange welding, nut & bolts etc complete in all respect as per site requirement with epoxy coating & as per approved specifications of the department, supply, erection & commissioning of solid shaft motor of capacity 30 hp, 1440 rpm, 3 phase, 380 volt+- 10%, with eficiency class ie2 suitable for fitment with 5 cs. v.t axial/mix flow pump type vertical flange mounted as per approved specifications of the department, supply, erection & commissioning of fully automatic star delta starter suitable for 30 hp motor as per ip 54 with all allied item like mccb, contactor, rating 120 amp 90 amp, 50 amp, all type of protection relays (over voltage, under voltage, over corrent, singhle phasing preventor, delay siwtch ) correction capacitor, digital meter, bus bar, thimble etc suitable and all live parts should be covered as per site demand and compartment coated with epoxy coating as per approved technical specification of department. (including cable suitable for panel to motor).

Digital Meter Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

Central Government/Public Sector

State Government

State Government