Tender For supply of c.v.m.c. assy bi 290662770b, part no.z2162400025 , solenoid valve, part no.z9926001066 , slave cylinder, part no.w7372000344 , dual brake valve, part no.8311788 , paper element lub oil filter, part no.f7a01500 , v belt, part no.f0t00800 , control sol eng stop, part no.x3992400 , toggle switch, part no.z7872000176 , toggle switch, part no.z7872000174 , relay 24v. 20amp, part no.7750000710 , sol switch, part no.x7750000001 , seal kit, part no.z9372005583 , seal kit, part no.z9372005924 , seal kit, part no.8341514 , seal kit, part no.z9372005599 , o ring kit, part no.8746962 , dowty seal kit, part no.8747018 , hose radiator top tank to eng, part no.x7543000643 , ac kit for rt880 crane, part no.v2167200067 , fuel filter, part no.f8835100 , hand control valve, part no.8412453 , caliper parking brake, part no.z9904100492 , air pressure gauge, part no.335002 , l.p.i.switch, part no.8311773 , system protection valve, part no.8312375 , press sender switch oil, part no.z7486000103 , temp sander, part no.z7486000104 , temp sensor, part no.z7486000166 , eng. clt. temp. gauge 24v 40 to 120deg.c, part no.z7486000093 , horn ht 24v, part no.x7025000017 , flasher unit 24v, part no.w7872000094 , stop light switch, part no.8311789 , head lamp rect., part no.x7581000147 , bulb 24v, part no.x7581000180 , connector head lamp, part no.x7346000007 , relay, part no.7750000058 , seal kit, derrick cylinder, part no.z9372011880 , brake fittings kit, part no.x2131600017 , solenoid deutsch 24v, part no.z9904002260 , solenoid valve, part no.8312280 , anti two block switch, part no.z9352000094 , slew brake and motion cut sol valve blk, part no.v7926000299 , master cylinder repair kit, part no.8340241 , air dryer, part no.z7926000289 , seal kit tele cylinder, part no.z9372011904
Tender For tender for supply of generator spares for 4mw bptg - bearing bush (de side) t 1429 tdps , bearing bush (nde) t 1430 tdps , bearing temp det (r type) t 1113 tdps , air temp det (r type) t 1669 tdps , pressure gauge t 0373 tdps , labyr seal de side(out) t 0242 tdps , labyr seal de side(in) t 1682 tdps , labyr seal nde side(out) t 0243 tdps , labyr seal nde side(in) t 1683 tdps , rotating rectifier assy t 1487 tdps , sight glass t 1049 tdps , slip ring carbon brush t 1236 tdps , slip ring carbon brush hol t 0294 tdps , shaft earthing carbon brus t 0675 tdps , shaft earth carbon brush hol t 0008 tdps , air temp detector(dial type) t 1492 tdps , bearing temp dete(dial type) t 1114 tdps , slip ring shaft assly(c a) t 0227 tdps , pmg t 3086 tdps , sponge adhe gasket t 02255 t 1557 tdps
Tender For supply of cac spare-assembly 10 inch inlet guide vane 9 vanes part no - 47500614001 , cac spare-valve check 6 inch x 150 cold discharge c1000 part no- 17437112 , cac spare-regulator pressure with gauge-cmc panel part no- 70361340 , cac spare-bearing-plain c950 by 2acii stg 2 part no- 68107218 , cac spare-seal air and oil assy part no- 67688325 , cac spare-bearing-th thrust 2acii part no- 68117647 , cac spare-pin roll 1 by 8 x 1 by 2 part no- 95533543 , cac spare-kit gasket and o-ring for airend nar10245929 part no- 47693542001 , cac spare-ring retainer 181a13cxrr356 part no - 95420279 , cac spare-ring retainer 184a13cxur575 part no- 95135505 , cac spare-bearing-th assy thr rev part no- 67755447
Tender For tender for supply of civil engineering lab & physics lab equipment-, clinometer, digital planimeter, optical square, prismatic compass with tripod, steel measuring tape, surveyor compass with tripod, offset rod, reading staff (light wt.)(4m , 5m , 6m), cross staff, bench top meter for measurement of water quality parameters with all accessories, magnetic stirrer with hot plate, automatic water distillation equipment double stage, electronic balance, jar test apparatus flocculator, fluoride ion meter (with fluoride electrode), double beam uv-vis spectrophotometer, micropipette single channel fully autoclavable 0.5-5ml, nessler tube, glass test tubes, laboratory hot air over, thermometer, b.o.d incubator, test tube, vertical autoclave, filtration assembly with oil free vacuum pump, petri dish, silica crucible (25ml,50m1, 100 ml), desicattor, bod bottle, digital cod digester (for 10 ml cod vials), chloroscope, porcelain dish, measuring cylinder, beaker, filter paper, funnel, conical flask, burette, burette. stand with rod,clam & boss head, penetrometer (bitumen test), ring and ball test appratus(softening point test of bitumen), ductility test of bitumen appratus, flakiness test apparatus, elongation test appratus, column buckling apparatus hanger loads vernier caliper, loading frame strain gauge beam setup digital force display digital strain display, spring oscillator, bar pendulum, pullingger’s apparatus, searle’s apparatus, stokes’s law apparatus, photo-electric cell experiment, numerical aperture of an optical fiber
Tender For supply of servo motor control valve, running time meter, 1-4 mxpu4 elbow, frp filter od 137, solenoid valve, sampling cock, seal ring, filter and permeate pump casing, o ring, shaft seal, casing p-1, i b bearing p-16, o.b. bearing p-18a, circlip internal p-18b, oil level viewer p-19d, bearing lock out p-22, o-ring bearing housing p-33b, deflector p-40, breather p-45, lip seal i.b. p-47, lip seal o.b. p-49, mech seal p-60, bearing lock washer p-69, cover gasket p-73, bolts p-171d, foot bolt p-171g, flexible hose h.p.feed inlet, chi 2-40 shaft seal, pressure tube 1000l, pressure switch, bearing ring p- 47a, spacing pipe -p - 64.c, slotted nut p - 67, pump head for pump p-2, stay bolt for pump p - 26, chamber complete p - 4, neck ring p - 45, neck ring retainer, chamber with bearing ring p - 4a, spacing pipe - p - 64.a, wear part kit - repair kit, ball bearing d244 p153, ball bearing p- 154, shaft pin p-10, chamber, o-ring 16.3 od x 2.4 thk, o-ring 137.5 od x 3.3 thk, chamber complete, chamber, neck ring, neck ring retainer, bearing ring, spacing pipe 17.52l, spacing pipe 4.50l, washer, 8.20id x 13.50od, shaft seal, impeller, shaftseal p-105, ball bearing p-153, anode plug, rod connecting assy, plug for priming, spacer v-packing p-157, o ring over hauling kit, piston set, retainer set, seal kit, seal ring, charging screw, charging plug screw, head distributor 3-4 air connection, o ring for head distributor assembly, cartridge filter housing, cartridge filter head, o ring hydraulic disc, solenoide valve actuator, 3 way ball valve, hp straight conn .3-4 for smcv, connector 1 1-4 bsp f x 1 1-4 vivt, vict end connector 1 , module bypass nozzle, victaulic couplings 1 1-4, victualic coupling 1. 1-2, coupler for vict. coup.1, victualic couplers 1. 1-2, permeate male elbow, smcv spindle seat, smcv valve unit for 3-4 valve, smcv valve spindle unit, servo motor control valve, solenoid valve 3-8 f 2-way ve83, solenoid valve actuator, ball v/v brass 1-4 bspf chrome plated, compressed air regulator, control cabinet ro 1530, door stay for cabinet, circuit breaker 1.6-2.5amp, circuit breaker 1.6-2.5 amp, thermister over load relay, single phase protector, hrc fuse 2 amp, hrc fuse 25 a, hrc fuse-bs-3nw 415vac 32 amp, main control switch 63a, potention meter, running hour meter, pressure gauge 0-10 bar, pressure transmitter, hand conductivity meter, flow meter feed, flow switch, sand filetr bracket, lp hose 32mm, hp line pressure gauge pi 61 hp pump discharge, hp hose 3-8id 1 2unfmx1 2unffx800l, high pressure hose module outlet, hp hose of module in, hp hose 1 idx1-vicx1500l saf 2507, lp hose hp pump inlet, pulley for motor 2 groove, pulley for pump 2 groove, seal kit, ho pump seat kit, taper bush 1610 20 mm bore, taper bush for motor pulley, wedge belt, av mount akcc 85m, av-mount between main frame and hp pumpbase frame, hp pump crank case oil, allen key set, socket dt module, belt spanner, jubilee clips for d 25, membrane cleaner 22, membrane cleaner 55, h.p connection - feed-brine, high pressure transmitter 4 to 20 ma pt60, high pressure manifold 6 x 1, rubber hose from c-f outlet to hp pump inlet 20-30tpd, abs service kit ro 200-102, abs service kit - 40 tpd, e-spare kit ro 0510-510, filter pump motor bearing pump end , hp pump seal kit, hop pump valve kit, hose for pk-20 pump in-out, level switch
Tender For supply of xtracem , 10 mm thick base plate 400x400 for column , column ismb 250x175 56.90kg rm 3 mtr long , beam ismb200x100mm 25.40kg rm for first floor and roof 2.4 04 nosmtr long , beam ismb150x75mm 15kg rm for first floor and roof 2.4 04 nos and 2.2 04 nos mtr long , 8 mm thick ms plate connection between column and ismb 200x200mm , normal nut bolts 150mm long 16mm dia , 8mm thick ms plate for first floor 2.4 x 2.2mtr , 6 mm thick gable side wall ms sheet 14 nos 2.40x0.30m and 7 nos 2.20x.30m , ms steel angle 65x65x6mm 5.80kg rm for stair case , column shs 75x75mm 04 nos 3mtr length , beam shs 45x45mm 05 nos 2.40 mtr length , 8mm thick ms plate 150x150mm connection between column and beam , cgi sheet 3mtr x 1 mtr , 8mm thick ms plate 0.15 x 0.15mtr , normal nut bolts 150mm long 12mm dia , foundation bolt 450 mm long dia 16mm , pvc cable insulated and pvc sheathed 10 sq mm 2 core , switch socket combination 16 amp 3 pin , switch socket combination 5 6 amp one way , t w switch board 10 inch x8 inch , t w switch board 7 inch x4 inch , t w switch board 4 inch x4 inch , main swithch 32 amp two pole 240 v , change over switch 16 amp two pole 240 v conforming to is making havells standard , led tube light fitting 1x18 w 4 feet long complete with all accessories incl tube rod , led bulb 20 w , flexible wire twin core 23 00076 conforming to is 9537 pt iii 1983 , pvc conduit pipe 20 mm dia conforming to is 9537 pt iii 1983 , pvc l bend for 20 mm conduit pipe 20 mm dia , pvc round block squareblock rectangle block for mounting of switches socket etc. , ms screw 20 mm conforming to revelent is pkt of 100 nos , ms screw 25 mm conforming to revelent is pkt of 100 nos , tape insulation in 2 cm width 10 mtr roll confirming to isi 12714 , pvc saddle clip 20 mmconforming to is 3419 1976 , pendent holder bakelite , pvc insulated cable and pvc sheathed 2.5 sq mm 1 core copper conductor conforming to is 694 1990 , mcb 16 amp double pole 240v confirming to is 8823 1978 , mcb 6 amp two pole 240 v , mcb distribution bds 8 way single door with blank , switch socket combination 6 amp 3 pin , pvc junction box 2 to 3 way for 20 mm conduit , pvc rawal plug for 25 mm screws , bakelite sheet 9 inch x 11 inch conforming to is 2036 , bakelite sheet 8 inch x 5 inch conforming to is 2036 , bakelite sheet 5 inch x 5 inch conforming to is 2036 , brick trowel steel 305 mm with handle. , brick hammer with handle weight 1.2 kg. , aluminimum straight edge 50mm squre 2mm thick 1800mm long , plaster trowel with hard wooden handle isi marked. , galvanised iron pan mortar tasla 16 gauge 16 inch dia minimum weight of 1.5 kg , fish line best quality. brick line , plumb bob iron best quality with all accessories. , rammer earth with 6 feet long hard wooden handle , picks axes with chiesel and point ends kudali 14 cp nominal weight 3.0 kg , showel square nose 14 gauge tata high carbon steel product , phowrah with hard wooden handles with min weight 2.00 kgs , painting brush 100 mm best quality. , multipurpose non slip rubber reusable gloves for scrubbing cleaning brick work etc , aluminium spirit level 12 inch , water leveling pipe pvc 50 mtr , cutting plier insulates 6 inch , measuring tape 15 mtr , wooden flat gurmala , drill bit 6mm dia , drill bit 8mm dia , drill bit 10mm dia , tape measuring metallic 30m , two tier sleeping bunk as per drawing attach and specification refer attach pdf file , prefabricated gel earthing electrode of pipe in pipe technology. , gi pipe 100 mm dia medium grade as per is specification 1239 , back fill compound , ms earth pit cover of size 30 cm x 30 cm with handle , aluminium strip //bid details 2 / 77 25 x3 mm x 9m , iron spikes 16 inch long complete as directed and specified by buyer , gi strip 32 x 6mm of length 3m , gi nipple 20 mm dia and 10 cm long is - 1879 , gi reducer socket 40 x20mm isi marked , lightning air terminal , ms clamp 25 x 3mm with nut and bolt complete , gi wire 12 gauge conforming to is 2062 1991 , earth augur one p
Tender For supply of mt 10 e e - slave cy clutch , air pressure gauge , rear brake chamber or actuator assy , spark plug , brake pad front , silencer comp , brake shoe rear , chain and sprocket kit