Get complete information related to latest Discharge Rod Tenders . from India at Classic Tenders. Search the best available tenders from Indian government tenders, domestic Discharge Rod Tenders , private tenders, online tenders, tender invitation notice, business tender notices, online tenders and bidding Discharge Rod Tenders.
Tender For supply of sleeve cylinder , piston piston pin with lock , ring set piston , bearing set crank shaft , bearing set connecting rod , bearing set crank thrust , bush connecting rod , bush cam shaft , cam tikki , valve inlet and exhaust , valve seat inlet and exhaust , valve guide inlet and exhaust , valve seal inlet and exhaust , oil filter engine , oil sending unit , temperature sending unit , thermostat valve , gasket set moh with head gasket , clutch plate , pressure plate , release bearing , fly wheel bearing , oil seal front , oil seal rear , filter fuel , filter element air , filter steering oil , bolt head , bolt connecting rod , bolt main cap , bolt with nut upper ball joint , clutch cylinder upper , clutch cylinder lower , fan belt , belt ac compressor , belt steering pump , injector over flow pipe crdi , shoe liner rear , disc pad front , ball joint lh upper and lower , nut with bolt 10 no and 12 no , annabond tube , araldite , banjo washer 14 17 19 , emery paper , old cloth , fuel pump assy tank , head light assy lh and rh , tail light assy lh and rh , fog light assy with bulb 12v , self starter solonide switch , solonide switch mounting screw , c e bush , needle bearing , insulation tape
Tender For supply of investment casting component- 920054030000-un machined door cover castings 100x250 mm as per drg.3-28-231-00006 and specification sa216 wcb , 920054400000-un machined bearing lever as per drg.3-45-836-00015 rev 01 and specification astm a297 gr hh , 920055910100-un machined lever main tilt var 01 as per drawing 3-45- 000-01433 rev 02 and tdc 0435 rev 00 specification astm a27 gr 65-35 with radiography test , 920055920100-un machined lever main tilt var 02 as per drawing 3-45-000-01433 rev 02 and specification a27 gr65-35 and tdc 435 rev 00 -with radiography test , 920055930100-un machined lever main tilt drive mech as per drawing 3-45-000-01159 and specification a27gr65-35 and tdc 435 rev 00 -with radiography test , 920055940100-un machined lever int bell crank var01 as per drawing 3-45-000-01434 rev 01 and specification a27gr65-35 and tdc 435 rev 00 -with radiography test , 920055970200-un machined rodendclevis small var 01 as per drawing 4-45-000-01482 rev 01 and specification a216grwca , 920055980200-un machined rod end clevis small var 02 as per drawing 4-45-000-01482 rev 01 and specification a216grwca , 920055990200-un machined rod end clevis large var 01 as per drawing 3-45-000-01156 rev 02 and specification a216grwca , 920056030200-un machined nozzle tip support block as per drawing 4-45-000-01481 rev 01 and specification sa351-18cr8ni , 920056040200-un machined nozzle tip support block cap as per drawing 4-45-000-01480 rev 01 and specification a351-18cr8ni , 920056200000-un machined diffuser cone extn lever as per drg.4-41-350-00877 rev 07 and specification sa216 gr wca , 920132240000-un machined nozzle tip operating lever casting as per drawing 3-45-325-00220 rev 03 and specification a216wcb , 920132760000-un machined nozzle tip bearing casting as per drawing 4-45-000-00697 rev 03 and specification a216wcb , 920400010000-un machined pin connecting lug as per drawing 3-45- 000-01655 rev 00 and specification sa351-18cr8ni , 920404830000-un machined pin connecting lug as per drawing 3-45-000-01158 rev 00 and specification sa351-18cr8ni , 920510040000-un machined diffuser disk casting as per drawing 3-41-125-00116 rev 04 and specification a560-50cr50nicb , 920510340000-un machined pin connecting lug dia 17 mm hole as per drg.4-45-325-00364 rev 03 and specification astm a297 grhh , 920510830000-un machined diffuser disc as per drawing 4-45-000-01470 rev 00 and specification a560-gr50cr50n
Tender For supply of spares and resetting of automatic contrivance and spares ofpower brake system of steam winder pin for brake post pb 1015 , pressure gauge for steam pb 973 , press reducer valve power brake engine pb 1006 , brake engine pb 007 , digital sensing unit sdr 30 , analague display unit sdr 33 , cable and accessories for analogue unit sdr 34 , distance piece for essv pb 1013 , tie rod for brake gear of braking system pb 1018 , connecting rod for brake gear of brk ss pb 1017 , controlling unit pb 001 , fixing and testing charges , resetting of automatic contrivance , supervision charges for ic -
Tender For machining and supply of 16 types of parts - tender for supply of connecting rod - l.h. , cartridge tube , adjuster (crutch pad) , top cover - small , side plate front , side plate - rear , connecting link. rigid , pin - connecting link , connector bracket , reinforcing plate. connector bracke , bush operating lever , pin , contact , cable clip , bracket , screw , special , plate
Tender For supply of needle roller bearing for hp connecting rod of compressors & expressors to model no. hj-283720 (or) mr-283720 (or) to elgi part.no.000903904. make -ntn/torrington/iko only. [ warranty period: 30 months after the date of delivery ]