Latest dissection box Tenders | Government dissection box Tenders

CTN :45696133

13 Jul, 2026 NA

Palacode - Tamil Nadu

Tender For supply of equipment for electronics and communication engineering department - supply of equipment for electronics and cmmunication engineering department, 8051 micro controller kit :specification : operating voltage: +5 v dc. flash memory: 4 kb (at89c51) / 8 kb (at89s52). ram: 128 bytes internal ram. 16 2 alphanumeric lcd display. push buttons / tactile switches. dip switches for digital input. inbuilt adc interface: ldr, potentiometer. inbuilt dac interface. inbuilt stepper motor driver with stepper motor. inbuilt dc motor driver with dc motor. 1 4 led array, 1 4 keypad, 1 relay. 1 buzzer, 16 2 lcd display, 1 pwm driver. 1 hardware interrupt key, inbuilt rtc. inbuilt eeprom and uart module. 4 7-segment display. supports both assembly and c language programming. pc interfaceable., temperaturemeasurementkitspecification : sensors:rtd (pt-100), thermocouple (fe-k/j-type), and/orthermistor (ntc). display: 3 digit led/lcd digital display(typically 200 mv fsd). temperature source: portable water kettle orheater block. signal conditioning: on-board circuitry foramplification, linearization, and cold junctioncompensation. test points: multiple 2 mm / 4 mm banana socketsfor monitoring input/output signals. power supply: 230 v ac, 50 hz, single-phase. accessories: glass thermometer, 10 k ntcthermistor probe, k-type thermocouple probe,patch cords and user manual., ask modulationanddemodulation kit:specification : message signal1:8-bit variable data,amplitude 5v. message signal 2:debounced data, amplitude low (0) and high (5 v). message signal 3:fixed data 25 khz, 12.5 khz, 6.25 khz, 3.12 khz,amplitude 5 v. carrier signal: sine wave, frequency 200 khz,amplitude 5 v. modulator type: switching modulator using analogswitch / transistor switching ic. demodulator: envelope detector and lpf. comparator: lm311 based. supply voltage (board): +12 v, +5 v dc. supply current: 100 ma minimum. input voltage: 230 v ac, 50 hz. interface connectors: 2 mm banana socket., dth trainer kit:specification :power supply: 200 v to 240 v ac, 50 hz.dish antenna: 1.5 ft aluminium steerable dish antenna.lnb (low noise block down converter): input frequency: ku-band. output frequency: 950 mhz to 1450 mhz. conversion gain: 65 db. noise temperature: 35 k (max).set-top box receiver in trainer form: if frequency: 70 mhz. video bandwidth: 50 hz to 5 mhz. video output level: 1 vpp at 75 load. video polarity: normal/inverted, switch selectable. audio subcarrier frequency:tunable from 5.0 mhz to 8.0 mhz. remote control provided. hdmi cable: 10 m.controls: channel selection. volume control.fault simulation: five built-in simulated faults for troubleshootingexperiments. if signal disconnected. video output fault. audio mute fault. tuner misalignment. rf output interruption.pcb size: 15" 12" with multicolour section-wise blockdiagram.standard accessories: 1.5 ft dish antenna. lnb. trainer pcb. dish connecting wire. audio-video cable. user manual. acrylic cover. hardware materials for assembly of dish antenna.additional features: dth subscription connection withdoordarshanfree channels. free-to-air channel demonstration., fpga trainer kit:specification : must use industry-standard mid-range fpgadevice usb-jtag programmable, compatible withvivado ise (webpack). power supply: 5 v dc through usb or externaladapter. on-board peripherals: leds, switches, pushbuttons, 7-segment display,clock source, gpio /pmod expansion ports, uart, vga / hdmi, usbuartbridge, usb cable. user manual.

Central Government/Public Sector

CTN :45571657

23 Jul, 2026 NA

Multi City - Multi State

Tender For corrigendum : control loading system for level d certifiable helicopter fms task trainer tt

Central Government/Public Sector

CTN :45688567

16 Jul, 2026 NA

Kangra - Himachal Pradesh

Tender For supply of glass petri plates 90 x15 mm pieces , lancets needles pack of 100 , test tube stand 40 holes plastic autoclavable for 27 ml 18x150 mm test tube , test tube for 27 ml 18x150 mm , glass vials with cap 15ml , plastic vials with cap 10ml , centrifuge tube 50 ml , cover slips rectangle pack of 20 , plane slide pack of 50 , measuring cylinder glass 500 ml , measuring cylinder glass 100 ml , measuring cylinder glass 10 ml , microtips plastic polypropylene autoclavable 1000 ul , microtips plastic polypropylene autoclavable 100 ul , microtips plastic polypropylene autoclavable 10 ul , separatory funnel glass 250 ml , surgical gloves medium size pack of 100 , surgical gloves large size pack of 100 , surgical masks pack of 100 , autoclavable bag large pack of 100 , sample bag plastic medium size pack of 100 , muslin cloth im meters , sampling bottles plastic100 ml , sampling bottles plastic 50 ml , aluminium foil in kg , butter paper pack of 50 , insect killing jar 500 ml , blotting sheet pack of 100 , grinder mixer 5 l capacity , volumetric flask, 100 ml , stainless steel sterilized blade no 24 pack of 100 , filter paper grade 42 pack of 100 , wash bottle 1 l , tissue roll double ply , dissection box set , insect collecting net with aluminium handle , plankton net , thermometer digital minus10 to 100 degee c

corporations/Associations/Others

CTN :45689433

10 Jul, 2026 NA

Ambarnath - Maharashtra

Tender For supply of copper calorimeter with stirror , magnetic needle on stand plastic , glass prism 38 x 38 , magnifying lens 3 inch , solar system eclips model , centrifugal machine 4 tube , hopes apts tin painted , galvanometer model no 65 with stand , dissection box , digital charts 5th to 10th , wire gauge with frame , convex lens 2 inch , convex mirror 2 inch , concave lens 2 inch , concave mirror 2 inch , newtons coloured disc model , microscope , pendulam bob iron 1 inch , plug key 1 way brass , plug key 2 way brass , ebonite rod 30 cm long , geometrical solid figuers , tunning fork set of 8 superior , bi metal strip , ring and ball apts , reflection of sound apts 12 inch x 18 inch s s fitting , voltmeter model no 65 with stand 10v , milli ammeter dc model no 65 with st , battery cell box on board 4 cell , magnetic compass 50mm dia , tripod stand medium , day and night model , seasons model , solar system model , phases of moon model , human respiratory system 2d model , human digestive sys 2d model , human blood circulatory sys 2d model , human nervous system 2d model , human skeleton 2d model , human heart 2d model , human ear 2d model , human exretory system 2d model , human brain 2d model , human eye 2d model , human reproductive male 2d model , human reproductive female 2d model , human skin 2d model , d n a 2d model , r n a 2d model , plant cell 2d model , animal cell 2d model , animal cell slide , ascariasis female slide , ascariasis male slide , amoeba binary fisson slide , anebena slide , aspergelis oryze slide , acetobacilus slide , acetobacter slide , animal tissue slide , azolla sporocarp v s slide , cardiac muscles t s slide , collenchyma slide , hyaline cartilage slide , hydra budding slide , lactobacilus acetophilus slide , malarial parasite palsmodium slide , mitosis slide set of 5 , miosis slide set of 12 , mucor slide , nerve slide , nostoc slide , onion tissue slide , ovary t s slide , plant cell slide , paramassium slide , parenchyma slide , strated muscles t s slide , sycon v s slide , sclerenchyma slide , sacharomyces slide , streptococus thermophilus slide , slide box empty for 50 slides , magic of magnet verticle , pythagorus therum , algebraic formula , area of a circle , appollonius therum , trignometry , mathematical symbol , decimal scale and conversion table , area model , geometrical constructions , roman numerals , xyz axis model , tetrahedron area and volume model , square pyramid area and volume model , hexagonal pyramid geometry model , cube geometry model , cuboid geometry model , triangular prism geometry model , octahedron geometry model , pentagonal prism geometry model , hexagonal prism geometry model , dodecahedron geometry model , sphere geometry model , ellipsoid geometry model , icosahedron geometry model , cone area and volume model , cylinder area and volume model , cube area and volume model , rectangular prism geometry model , tetrahedron geometry model , square pyramid geometry model , n gonal pyramid geometry model , triangular prism geometry model , n gonal prism geometry model , cylinder geometry model , cone geometry model , truncated cone geometry model , spherical wedge geometry model , spherical cap geometry model , spherical segment geometry model , geometry box , angle of earth moon and sun model , digital geographical images photos , earth internal diagram 1 , earth internal diagram 2 , earth internal diagram 3 , earth internal diagram 4 , earth round globe , four hemisphere , four sides and subsides , india major states , kit of digital charts for geography 6th to 10th , latitude longitude and equator , maharashtra major districts , major countries in two hemisphare , phases of moon krushan and shukla paksha , rain guage , rock cycle , rotation of sun earth and moon , season model , star dial , structure of enviorment , sun and shadow model , sun dial model , telescope astronomical , time zone indicator , time zone puzzle , types of rocks , volcano model , waves of earth

CTN :45697944

13 Jul, 2026 75.00 Lacs

Dhanbad - Jharkhand

Tender For supply of pn or zener diode or led characteristics apparatus , verification of kcl and kvl , resistance in series and parallel apparatus , ohms law apparatus without power supply , ohms law apparatus with aluminum panel 2 digital panel meters and power supply , transistor characteristics apparatus , fet characteristics apparatus , half wave full wave and bridge rectifier apparatus , ripple factor apparatus , digital logic trainer , verification of truth table of logic gates using universal gates , flip flops using nand gates and ttl ics , four bit counters synchronous and asynchronous , four bit shift registers , encoder or multiplexer eight to one line , decoder or demultiplexer one to eight line , four bit analog to digital convertor , four bit digital to analog convertor , light intensity or phase control using scr or triac , scr commutation techniques , switching action of a bjt , single phase half wave full wave and fully controlled bridge rectifier or convertor using scrs , three phase half controlled bridge converter with r and rl load , three phase fully controlled bridge converter with r and rl load , single phase cycloconverter , instrumentation trainer using transducers , burdon tube pressure gauge trainer kit , strain gauge trainer kit with cantilever beam , lvdt trainer kit , speed measurement using photo electric and magnetic sensors , temperature sensors kit , measurement of water level using strain gauge , measurement of water level using capacitance transducer , ac servo speed torque characteristic trainer , dc servo motor speed torque characteristics trainer , stepper motor controller trainer , analog lab trainer bread board model , digital lab trainer bread board model , plc trainer , transmission line trainer abcd t and pi parameters ferranti effect load test , idmt over current relay testing kit electromechanical type , buchholz relay testing kit with compressor and oil , over voltage relay testing kit electromechanical type , over current and earth fault relay testing kit three phase static type , over current relay testing kit static type , measurement of power and power factor single phase and three phase , to study a typical bhk house wiring , four to one multiplexer and one to four demultiplexer , vapour compression refrigeration vcr test rig , water cooler setup , air conditioning test rig , domestic refrigerator , window air conditioner , split air conditioner , air cooler evaporative , tube cutter , pipe bender , flaring and swaging tool kit , reamer , brazing torch , manifold gauge set , vacuum pump , refrigerant recovery unit , refrigerant charging cylinder or electronic charging scale , refrigerant leak detector , digital clamp meter , digital thermometer , anemometer , tachometer , insulation material , refrigerants , recovery cylinders , weighing machine , electrical control panel , work benches , safety equipment

CTN :45469316

27 Jun, 2026 NA

Lunavada - Gujarat

Tender For corrigendum : supply of ballpoint pen blue , ballpoint pen black , ballpoint pen red , pencil , summoner , rubber , foolscape chopra 172 page , single line notebook , four line notebook , post cover , answer book 16 pages , answer book 8 pages , supplement left 4 pages , answer book 24 pages , a4 size paper reem , legal size paper reem , permanent marker , color chalk , duster marker duster , chalk duster , white board marker blue , white board marker black , whitener , lined lined pad register 100pg , lined lined pad register 200pg , lined lined pad register 300pg , cello tape , white chalk , school bag , compass , sketch pen , foot tape , teacher daily notebook , teacher attendance sheet , student attendance sheet , scissors large , stapler small , stapler large , stapler pin small , water color , cobra file , box file , fevicol , spring file , stamp pad , oil pastel color pencil box , sketch book drawing book , water bottle , push pin large , carbon paper , notice book , tag packet 6 inches , visitor register , movement register , proxy book , calculator large , dissection box

CTN :45558359

30 Jun, 2026 NA

Coimbatore - Tamil Nadu

Tender For purchase of lab equipment for mechanical (workshop) - purchase of lab equipment, 3d printer (technical specification - refer with nit), rp2040 carrier board (technical spectfication - refer with nit), 8051 micro kit vptb (technical spectfication - refer with nit), level control system trainer (technical spectfication - refer with nit), traffic light control system (technical spectfication - refer with nit), stefan boltzma nn apparat us (technical specification - refer with nit)

CTN :45416327

16 Jun, 2026 11.00 Lacs

Payyanur - Kerala

Tender For supply of multi process control trainer setup for instrumentation engineering lab under mhrd scheme - purchase of multiprocess control trainer setup for instrumentation engineering lab under mhrd scheme - multiprocess control trainer set up, multiprocess control trainer set up - specifications:- setup must contain flow, pressure, level, temperature loops also derived loops like cascade and feedforward loops. temperature loop must be independent. setups consist of a circulating closed loop water plant or circulating water system including control valve, tanks, independent pumps and necessary valves including bypass valves and rotameters. using this we can be able to do flow control loop with pid,level control loop with pid,and pressure control pid, as independent experiments.the setup must include the following:1.one linear characteristics diaphragm operated control valve with 15mm stroke 1/2-inch size, type: high-capacity globe seat leakage class (as per ansi/fci 70.2).2.measuring tank with volumetric measurement scale and 1000mm level, in of 25 ltr capacity. sump tank min of 40 ltr capacity. all tanks made of ss304, with sight glass, and finished with mat steel finish.3.2 no s smart dp transmitter for flow and level measurement with hart protocol, display and keys integrated for calibration,0-1000mmh2o measurement range,0.01% accuracy, international iso certified ce approved make,24v supply,4-20ma output, loop powered.4,1nos of magnetic flowmeter with display and keys integrated for calibration,0-2000lph measurement range, read out: 0 - 100%, 4-20ma lcd display,0.05% accuracy, international iso certified ce approved make,24v supply,4-20ma output to measure flow as a independent loop.5,. smart pressure transmitter and temperature transmitters with hart protocol, display and keys integrated for calibration, pressure transmitter 0-10bar measurement range, read out: 0 - 100%, 4-20ma lcd display,0.05% accuracy, temperature transmitter 0-250 rtd type international iso certified ce approved make,24v supply,4-20ma output, loop powered.6, pressure tank of 24 liters with necessary valves for pressure loop.7.1nos orifice plate (ss304) and assembly grade with flange 1/2-inch size for flow measurement.8.2 nos pumps 0.5hp, ss centrifugal pump, minimum 1-inch pipeline of ss or high-pressure withstanding plastic with plastic welding.9. rotameters 2nos 1 inch size flow: 200-2000 l/h,ss thread, clear acrylic type.10, plc control station with 4 analogue inputs and one analogue output with necessary digital inputs and outputs to operate all loops directly from panel side.plc must have ethernet connectivity with supported protocols profinet and modbus tcpip.11.required all pneumatic components to full fill the process loops such as fr,needle valves etc.12,i to p converter 4-20ma to 3-15psi with 1/4" process connection with proper copper copper tubing.13, loop including flow pid control, level pid control, pressure pid control, cascade control (level flow), ratio control (flow flow).14.all loops can be operated using a scada system and independent pushbutton control includes trend of all analogue signals and pid tuning. scada direct profinet connectivity to plc and computer with intel i5 processor, 8gb ddr3 ram,1tb sata hdd,licenced windows 11 professional.15, required a standalone software application that must be installed on pc in which it can used to control and monitor all the functions used in scada. the application must contain process parameter trend graph plot for to study about process loops.16.the whole system setup must be in ms powder coated standalone mobile table with lockable castor wheels. all the components used be industrial. copper tubing for air connection, pressure gauges 4inches 3nos, electrical wiring connection to be flexible for to connect field devices. panel with switches, indicator, test points with banana connectors as required, multistrand wire with proper insulated lugs, ferruling & neat wire dressing & clam

CTN :45404144

09 Jun, 2026 NA

Palacode - Tamil Nadu

Tender For supply of equipment for electronics and communication engineering department - supply of equipment for electronics and cmmunication engineering department, 8051 micro controller kit :specification : operating voltage: +5 v dc. flash memory: 4 kb (at89c51) / 8 kb (at89s52). ram: 128 bytes internal ram. 16 2 alphanumeric lcd display. push buttons / tactile switches. dip switches for digital input. inbuilt adc interface: ldr, potentiometer. inbuilt dac interface. inbuilt stepper motor driver with stepper motor. inbuilt dc motor driver with dc motor. 1 4 led array, 1 4 keypad, 1 relay. 1 buzzer, 16 2 lcd display, 1 pwm driver. 1 hardware interrupt key, inbuilt rtc. inbuilt eeprom and uart module. 4 7-segment display. supports both assembly and c language programming. pc interfaceable., temperaturemeasurementkitspecification : sensors:rtd (pt-100), thermocouple (fe-k/j-type), and/orthermistor (ntc). display: 3 digit led/lcd digital display(typically 200 mv fsd). temperature source: portable water kettle orheater block. signal conditioning: on-board circuitry foramplification, linearization, and cold junctioncompensation. test points: multiple 2 mm / 4 mm banana socketsfor monitoring input/output signals. power supply: 230 v ac, 50 hz, single-phase. accessories: glass thermometer, 10 k ntcthermistor probe, k-type thermocouple probe,patch cords and user manual., ask modulationanddemodulation kit:specification : message signal1:8-bit variable data,amplitude 5v. message signal 2:debounced data, amplitude low (0) and high (5 v). message signal 3:fixed data 25 khz, 12.5 khz, 6.25 khz, 3.12 khz,amplitude 5 v. carrier signal: sine wave, frequency 200 khz,amplitude 5 v. modulator type: switching modulator using analogswitch / transistor switching ic. demodulator: envelope detector and lpf. comparator: lm311 based. supply voltage (board): +12 v, +5 v dc. supply current: 100 ma minimum. input voltage: 230 v ac, 50 hz. interface connectors: 2 mm banana socket., dth trainer kit:specification :power supply: 200 v to 240 v ac, 50 hz.dish antenna: 1.5 ft aluminium steerable dish antenna.lnb (low noise block down converter): input frequency: ku-band. output frequency: 950 mhz to 1450 mhz. conversion gain: 65 db. noise temperature: 35 k (max).set-top box receiver in trainer form: if frequency: 70 mhz. video bandwidth: 50 hz to 5 mhz. video output level: 1 vpp at 75 load. video polarity: normal/inverted, switch selectable. audio subcarrier frequency:tunable from 5.0 mhz to 8.0 mhz. remote control provided. hdmi cable: 10 m.controls: channel selection. volume control.fault simulation: five built-in simulated faults for troubleshootingexperiments. if signal disconnected. video output fault. audio mute fault. tuner misalignment. rf output interruption.pcb size: 15" 12" with multicolour section-wise blockdiagram.standard accessories: 1.5 ft dish antenna. lnb. trainer pcb. dish connecting wire. audio-video cable. user manual. acrylic cover. hardware materials for assembly of dish antenna.additional features: dth subscription connection withdoordarshanfree channels. free-to-air channel demonstration., fpga trainer kit:specification : must use industry-standard mid-range fpgadevice usb-jtag programmable, compatible withvivado ise (webpack). power supply: 5 v dc through usb or externaladapter. on-board peripherals: leds, switches, pushbuttons, 7-segment display,clock source, gpio /pmod expansion ports, uart, vga / hdmi, usbuartbridge, usb cable. user manual.

CTN :45404156

16 Jun, 2026 NA

Chennai - Tamil Nadu

Tender For supply of lab equipment for department of instrumentation and control engineering - i/p and p/i converter, pressure measurement using bourdon tube and lvdt setup, level measurement using float and sight glass indicator, temperature transmitter trainer kit, single phase transformer with load, saybolt viscometer, on off control of temperature process, flow measurement using electromagnetic flowmeter

Dissection Box Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

Central Government/Public Sector

Central Government/Public Sector

corporations/Associations/Others