Tender For supply of condenser blade , 4 mfd capacitor , samsung timer , white wrapping tape , teflon tapes , cello tape 2 black , cotton waste , danfoss relay set 20 deep freezer , 80 by 100 mfd capacitor , minus 20 deep freezer square type , pin remover charging , thermostat minus20 , relay danfoss , capacitor 4 mfd , condenser fan blade for 2 ton llyod ac , pinch pliers , t handle 10inch , t handle 12inch , sand paper , 1 by 4inch ratchet , refrigerant recovery plier , allen key set in inches , cold room evaporator fans , 8 mfd capacitor , nose pliers , wire cutter , charging line r32 , two way manifold gauge with box and hose , 46 pcs set , cylinder key , tourch for butane gas cylinder , swaging tools , rough file with handle , double end spanner set 6x32 mm , t set 13inch , t set 14inch , drain line spring , single gauge high side , measuring tape 5 meters , expansion valve for cold room , condenser motor , capacitor 3 mfd , digital temp meter , samsung heater , timer , condenser fan blade , valve 3by8inch hand shut off , cylinder valves , condenser motor , fan blade , hand cutter blade iron , adjustable wrench 6inch , adjustable wrench 8inch , adjustable wrench 12inch , allenkey set mm , flaring tools set with box , smooth file with handle , r22 charging line , t handle only 1by4inch , multitec screw driver , t handle 8inch , t handle 11inch , t handle 13inch , tube cutter , flare nut 3by4inch , square type condenser fan motor , tong tester with probes and leather cover , screw driver long , hammer with wooden handle , cutting plier , tube cutter small , hexa frame with blade , evaporator fan motor for lg refrigerator , condenser copper coil make llyod , filter , single pressure gauge high side500psi , gauge value , danfos 20 relay olp set , try square set , valve core removal tool , digital vernier callipers with batteries , siron soldering iron set , soldering wire , ) /bid number : gem/2025/b/6597172 * /dated: 22-08-2025 & & / bid document 1 / 87 & & ' ' /item category compressor cable kit , handset valve 1by4inch , cuppler , 24 socket wrench set ratchet , pin valve , charging line handle , capacitor 50 mfd , 3 way 30 amps connector , ss tank nipple 1by2inch , pvc connection pipe 1 by 2 inch , ro water purifier t type tap , ro water purifier tap tank kent type , charging line rubber , pipe wrench 16inch , bearings , oil seal , ss breazing roads , bluestar indoor blower for 1point5 ton sac , line tester , screwdriver small , screwdriver large , handle t , jet pump handle small , araldite 500gms , double ended ring spanner set , single guage low pressure for vaccume , t type handle spanner set , continuity tester compressor check , servicing covers , compressor for 345 liters refrigerator , electrical relay , compressor for minus20 deep freezer 320 liters , compressor for 165 liters bpl make refrigerator , compressor for minus20 deep freezer 350 liters , filter drier pencil type , compressor for -20 deep freezer 500 liters , compressor for 1point5 tr split ac rotary type , side dummy nuts 5by8inch , side dummy nuts 1by2inch , side dummy nuts 1by4inch , side dummy nuts 3by8inch , dummy nuts 1by4inch , ductable split ac indoor blower , rubber bushes , minus20 deep freezer compressor , drier cum filter , refrigerant r 600a , hand shut valve for r600a portable cylinder , water pipe pvc , acetylene cylinder regulator , oxygen cylinder regulator , hose pipe for acetylene , hose pipe for oxygen , torch for oxygen acetylene cylinder , clamps for hose pipes , hand hacksaw bladed , axial fan motor for hitachi 16point5 ton ac , compressor for ice machine 120 kg per hr production , filter cum drier , compressor for bluestar split ac 1point5 ton , capacitor 45 mfd , capillary tube gauge , soldering liquid flux , blower for lloyd make split ac 1point5 ton , pvc pipe 3by4inch , pvc bends 3by4inch , pvc pipe 1inch , pvc bend 1inch , clamps 3by4inch , clamps 1inch , pvc t joint 3by4inch , pvc solvent , cutting machine blade , vc t
Tender For repairing of delivery line of pumpset no.7 and 8 along with allied work at 2nd 40 mgd cwph plant at wazirabad water works. (re-invite) - hydraulic excavator (3d) with driver and fuel.dsr no. 0020, hire and running charges of crane 20 tonne capacity.dsr no. 0028, pumping out water caused by springs, tidal or river seepage, broken water mains or drains and the like.dsr no.14.23, providing and constructing bund with filled up earth in empty (pvc) cement bags (excluding the cost of earth which will be available at site of work) i/c stitching and stacking and placing in position etc. complete and i/c cost of empty plastic bags and removal of the same after completion of the work. providing and stacking of earth filled gunny bags to make the bund to give the dry condition of work. dsr no.26.1.19, taking out ms pipes of 600mm dia. from the trenches after de-jointing and stacking the same along the trenches within a lead of 50 meters. approved rates., providing ms pipe fabricated/manufactured out of ms plate of steel grade fe410 as per is 3589:2001 or out of hr coils of same/equivalent grade;coated internally with food grade epoxy and externally/outside with epoxy coating;complete in all respect as per relevant is codes with upto date amendments and as directed by engineer-in-charge.600mm nominal dia. (clear internal dia.) pipes of 8mm thickness (min.).approved rates.make skf / fag, laying in position m.s. pipes/steel cylinder reinforced concrete pipes suitable for rubber ring jointing or welding or flanged jointing (excluding cost of pipe). approved rates., 50 % neoprene (1.5 mm to 25 mm).sor no.22.6.1, cast iron non rising sluice valve of size 600mm, pn 1.0 for clear water application, flanged end as per is : 14846 body,dome,wedge- ci is:210, gr.fg260 body & wedge rings bronze is:318 gr. ltb2, spindle-ss is:6603, gr.12cr12, gland packing- greasy jute, packing fasteners- cs, is:1367, cl-4.6/4.0, gasket natural rubber, flange drilling - is:1538, table 4 & 6.make :- kbl /ivc/djb approved. sor.4.12.13, providing of ms flange(1set) suitable for the above sluice valve along with suitable size nut-bolts for making flange joints complete as per site requirement., installation of sluice valves with the help of all labour like fitter, welder, cutter, helper, beldar, chowkidar, supervisor, electrician and material used like welding machine, cutter set i/c oxygen cylinder, welding road t&p along with its all transportation loading, unloading complete at site of work., testing and commissioning of sluice valve on full pressure as per satisfaction of engineer-in-charge.