Tender For corrigendum : supply installation and commissioning of lab. equipment for electrical engg dept - low power factor wattmeter portable electrodynamometer type single phase,0.5/1a62.5/125/250v, wattmeter portable electrodynamometer type single phase, 1/2a, 75/150/300v, wattmeter portable electrodynamometer type single phase, 2.5/5a, 125/250/500v, wattmeterportable electrodynamometer type single phase, 5/10a, 150/300/600v, wattmeter portable electrodynamometer type single phase, 10/20a,150/300/600v, wattmeterportable electrodynamometer type single phase, 15/30a,150/300/600v, power factor meter portable electrodynamometer type single phase, 1/2a, 75/150/300v, power factor meter portable electrodynamometer type single phase, 5/10a, 150/300/600v, digital laboratory trainerbreadboard- solder-less large size, spring loaded breadboard consisting of two terminal strips with 1280 tie points and 4 distribution strips with 100 tie points eachregulated dc power supply - +5v at 1amp, -5v at 500 ma, 3 to +15v at 500ma, and -3 to -15v at 500 mapulse generator : 1 hz to 1 mhz in 6 steps. variable in between steps- amplitude : 3-15v (cmos), 5v (ttl)- duty cycle : 50% ttl/ cmos outputpulsar switches : 2 independent buffered bounce free manual pulser (useful for freezing the action of each stage of the counter after every clock pulse)data switches : 12 nos. independent buffered logic level inputs to select high / low ttl levels, each with a bi-color led to indicate high / low status and termination.logic indicators : 12 nos. independent buffered logic level indicators for high / low status indication with bi-color led for digital outputsseven segment display : 2 nos. bcd to seven segment decoder / driver ic with terminalslogic probe : logic level indicator for ttl/ cmospower : 230 v 10%, 50 hzto be provided : ics-4001/1, 4049/1,4069/1, .7400/1, 7402/1, 7404/1, 7406/1, 7408/2, 7410/2, 7411/3, 7420/2,7432/3, 7474/2,7476/2,7486/1.resistors-330e/1,1k/2, 1k8/1,,15k/1, 47k/1.1m/2, capacitors- 0.01mf/1, 0.1mf/1, 0.22 mf/1,crystal-32.768mhz/1. main cords, operating and experimental manual, red & black patch cords with pin 10 each, red & black patch cord (pin to pin) 10 each. wire 24/25 swg. 1meter each, 5 colour instructiondetailed operating manual along with instructional details. experiment to be conducted01. to verify logic gates operation02. to verify de-morgan s theorem with boolean logic equations03. to perform binary to gray code conversion04. to perform gray code to binary conversion05. performance of binary adder and subtractor06. performance of johnson counter07. performance of of flip-flops rs, jk, d&t08. performance of multiplexer and demultiplexer09. performance of 4 bit binary up and down counter10. performance of shift register (sipo), analog lab trainerbread board: solder-less large size, spring loaded breadboard consisting of two terminal strips with 1280 tie points and 4 distribution strips with 100 tie points each, totaling to 1680 tie points.regulated dc power supply : +5v at 1amp, -5v at 1amp, +12v/0 to 20v at 500ma, and -12 v/0 to -20v at 500 maac supply : 5-0-5v, 10-0-10v at 100ma. can be used as 5v,10v,15v,20v and also as center tapfunction generator : sine / square / triangular waveforms frequency 1 hz to 110 khz in 5 steps. variable in between steps.sine / square / triangular waveform output 50mv ~10vpp variablemodulation generator : sine / square / triangular wave forms frequency 1 hz to 110 khz in 5 steps. variable in between (100khz ) steps. sine / square / triangular waveform output 50mv ~ 10vpp variable with 100 khz modulationdigital meter (3 digit) : dual range dc voltmeter 0-20 v /ammeter 0-200macontinuity tester : for testing the continuity. provided with beeper soundpotentiometers : 3 potentiometers (1k, 100k and 100k) with terminalson board switches : 2 switches single pole double throughpower : 230 v 10%, 50 hzaccessories / components / manual to be provided : resistance 5% 1w 100e/1, w 47e/2,100e/1, 220e/1,
20 Nov, 2024
NA
