Latest escalator spares Tenders | Government escalator spares Tenders

Central Government And Public Sector

CTN :39569459

21 Mar, 2025 NA

Multi City - Multi State

Tender For guide roller with nut for spray lift table to rwf drawing no712931010330 (item no 1 & 2).m aterial test certificate from nabl accredited lab shall be submitted along with the supply. [ warranty peri od: 30 months after the date of delivery ]

CTN :39302081

12 Mar, 2025 NA

Cuttack - Odisha

Tender For corrigendum : procurement of turn table ladder with lift (64 mtrs)

CTN :39361666

03 Mar, 2025 50.00 Lacs

Kishangarh - Rajasthan

Tender For w no 14 different works-, earth work in excavation for roadway, including trimming bottom and side slopes in accordance with requirement of line, grades and cross sections, including disposal of surplus material with all lift and lead upto 1000 metre as per mort&h specification clause 301.in all type of soil, carriage of materials bymechanical transport including loading,unloading and stacking :: earth for 1 km, providing and laying lean cement concrete 1:4:8 in sub- base over a prepared sub-grade with coarse and fine aggregate conforming to is: 383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per table 600-1, cement content not to be less than 150 kg/ cum, optimum moisture content to be determined during trial length onstruction, concrete strength not to be less than 10 mpa at 7 days, mixed in a batching plant, transported to site, laid manualy, ompacting with surface vibrator, finishing and curing complete as per clause 601, 112 of mort&h specification including all material, labour, machinery, lighting, guarding and maintenance of diversion., providing and laying un-reinforced, plain cement concrete mix with concrete mixer & vibrator pavement over a prepared sub base with 43 grade cement , coarse and fine aggregate conforming to is: 383, maximum size of coarse aggregate not exceeding 25 mm, mixed as per approved mix design, laid, spread, compacted and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints etc including all material, labour, machinery, lighting, guarding and maintenance of diversion. 9.6.1 pcc m-20, providing, lowering, laying in trenches, aligning, fixing in position and jointing socketed rubber gasket type isi marked upvc pipes of class iii (6 kg/sqcm) suitable for potable water with rubber ring joints (as per is 4985-2000) of following outer dia with all accessories (excluding specials) complete including all material, labour, hydraulic testing and commissioning as per technical specifications and as per direction of engineer., providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and testing of joints complete as per direction of engineer in-charge. exposed on wall 20 mm nominal outer dia .pipes., earth work in excavation in foundation, trenches etc. includingdressing of sides and ramming of bottoms, including getting out theexcavated material, refilling after laying pipe/ foundation anddisposal of surplus excavated material at a lead upto 50m suitablesite as per direction of engineer for following depths, below naturalground / road top level. in all types soils/ saturated soil such as moorum, sand, sandy silt, clay, black cotton soil, kankar, etc. depth upto 1.5 m, carriage of materials bymechanical transport including loading,unloading and stacking :: earth for 1 km, providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - all work upto plinth level code) 1:4:8 (1 cement : 4 fine/ coarse sand : 8 graded stone aggregate 40 mm nominal size)., "providing and laying in position cement concrete of specified gradeexcluding the cost of centring and shutteringt - all work upto plinth level1:1:3 (1 cement : 1 coarse sand : 3 graded stone aggregate 20mm nominal size)", 40 mm thick fine dressed stone flooring over 20 mm (average) thickbase of cement mortar 1:5 (1 cement : 5 coarse sand) includingpointing with cement mortar 1:2 (1 cement : 2 stone dust) with anadmixture of pigment to match the shade of stone.30.27.1 red sand stone, providing and fixing of reinforced ferro-cement drain covers designed for 'a' class loading duly marked on co

CTN :39491742

07 Mar, 2025 33.31 Lacs

Dausa - Rajasthan

Tender For gsb wbm work ward no. 26 to 55, dausa. - providing, laying, spreading and compacting of granular sub-base by providing close graded material (table 400-1), spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at omc, and compacting with vibratory roller to achieve the desired density, complete as per mort&h specification clause - 401 including all material, labour, machinery, lighting, guarding and maintenance of diversion., grading - iii material, coarse graded granular sub-base material 53 mm to 26 .5mm, carriage of materials (by mechanical means) stone, boulders, gravelly material 5 km, dressing of earth work in surface excavation including cutting and filling upto 30cm depth including disposal of excavated earth upto 50m and lift upto 1.5 m., construction of embankment with approved material obtained from borrow pit with all lifts and leads, transporting to site, spreading, grading to required slope and compacting by vibratory roller 8-10 tonne to meet requirement of table 300-2 including cost of compensation for earth taken from private land complete as per mort&h specification clause 305. (lead taken upto 5 km), random rubble masonry with hard stone in foundation and plinth : cement mortar 1:6 (1 cement : 6 coarse sand), providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - all work upto plinth level 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)drain work, providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - all work upto plinth level :1:4:8 (1 cement : 4 fine/ coarse sand : 8 graded stone aggregate 40 mm nominal size)., providing at site, lowering & laying in trenches, aligning & jointing of rcc pipes np3 class (with s/s ends) is: 458 - 1988 (amended up to date) marked and pipes from 300 mm upto 2000 mm manufactured through vertical / vibrated casting process all levels with rubber gaskets (epdm/sbr) for sewer lines as per is: 5382 (including cost of rubber gaskets lubricants) as per drawing, sectional hydro testing of the sewer pipe line (including cost and conveyance of water to site for testing) etc., complete as directed by engineer. note : e/w to be measured and paid separately. length of pipe shall be measured in between the outer wall of two manholes / inspection chambers. pipe in the manhole/inspection chamber s wall shall deemed to be included in the item of manhole/inspection chamber shall not be payable., 450 mm internal diameter, 600 mm internal diameter, hydraulic excavator of 1 cum bucket (with deasel, driver & helper)

CTN :39490145

19 Mar, 2025 NA

Coimbatore - Tamil Nadu

Tender For supply of scissor lift table

CTN :39487539

04 Mar, 2025 33.31 Lacs

Dausa - Rajasthan

Tender For gsb & wbm work ward no. 26 to 55, dausa.-, providing, laying, spreading and compacting of granular sub-base by providing close graded maternal (table 400-1), spreading in uniform layers with motor grader on prepared surface, mixing by max in place method with rotavator at omc, and compacting with vibratory roller to achieve the desired density, complete as per mort&h specification clause 401 including all material, labour, machinery, lighting, guarding and maintenance of diversion, , grading-iii maternal, , coarse graded granular sub-base material 53 mm to 26.5mm, , carriage of materials (by mechanical means) stone, boulders, gravelly material 5 km, , dressing of earth work in surface excavation including cutting and filling upto 30cm depth mcluding disposal of excavated earth upto som and lift upto 15 m, , construction of embankment with approved material obtained from borrow pit with all lifts and leads, transporting to site, spreading, grading to required slope and compacting by vibratory roller 8-10 tonne to meet requirement of table 300-2 including cost of compensation for earth taken from private land complete as per mort&h specification clause 305 (lead taken upto 5 km), , random rubble masonry with hard stone in foundation and plinth cement mortar 16 (1 cement 6 coarse sand), , providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering all work upto plinth level 124 (1 cement 2 coarse sand 4 graded stone aggregate 20 mm nominal size), , drain work, , providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering all work upto plinth level, , 148 (1 cement 4 fine/coarse sand 8 graded stone aggregate 40 mm nominal size), , providing at site, lowering & laying in trenches, aligning & jointing of rcc pipes np3 class (with s/s ends) is. 458-1988 (amended up to date) marked and pipes from 300 mm upto 2000 mm manufactured through vertical / vibrated casting process all levels with rubber gaskets (epdm/sbr) for sewer lines as per is 5382 (including cost of rubber gaskets lubricants) as per drawing, sectional hydro testing of the sewer pipe line (including cost and conveyance of water to site for testing) etc., complete as directed by engineer note e/w to be measured and paid separately length of pipe shall be measured in between the outer wall of two manholes /inspection chambers. pipe in the manhole/inspection chamber's wall shall deemed to be included in the item of manhole/inspection chamber shall not be payable., , 450 mm internal diameter, , 600 mm internal diameter, , hydraulic excavator of i cum bucket (with deasel, driver & helper)

CTN :39479284

17 Mar, 2025 NA

Indore - Madhya Pradesh

Tender For supply of 135 inch led videowall panel with 1 6 mm pixel pitch , detachable control system for videowall , cardioid pre polarized condensor on table boundary layer microphone , pre polarized condensor gooseneck microphone , dsp full rack 19 1 ru processor , pair rimless 5 5 in celling loud speaker 20 watt , four channel poe amplifier with integrated dante networking , gio usb power consumption 5 w , poe injector , hd base t distribution amplifier upto 70 mtrs , hdmi 4 1 hdmi switcher 4k uhd capabilty 60hz , hdmi over hd base t reciever , monitorized lift for monitor emament magnet dc motor drive , poe managed switch 8 port , cable cubby , conf table with custom race ways , integration programming and installation charges

CTN :39458206

17 Mar, 2025 NA

Shimla - Himachal Pradesh

Tender For supply of boq1 boq1 - the overall size of chair shall be : width 660mm , depth 660mm & height 1250 to 1350 mm. seat size shall be : width 490mm, actual depth520mm, effective depth 430mm and height 475mm to 575mm. width of the back shall be 425mm at bottom & lumbar level 440mm & min480mm at shoulder level. back height shall be 690mm as measured from seat level. the chair shall be supplied with high quality mesh at theback. back outer shall be injection moulded with nylon gf30% material. seat should be made up of foam pre moulded at 55 kg/m3 density &hardness of 25+ 3kgf at 50% deflection conforming to is 3400.the chair shall be supplied with dynaflex two piece back construction withis20d mesh upholstred. back shall be provided with 260mm width, 160mm height and 50mm height adjastable headrest thickness of seatfoam shall be 55 mm. seat shall be upholstered with micro fabric 100% polyster 180 gsm having abrasion > 50000 cycles fire rated fabricconfirming to bs en 1021. plywood used shall be 12mm thick 9 ply hot pressed. the chair should be provided with synchro tilt mechanism(bio snchyro mechansim) allowing 360 degree revolving movement along with height adjustablility & tilt tension. the mechansim shall allowseat to back recline ratio of 2:5. the gas lift used shall be class 4 tested as per ansi bifma standards. height adjustable arms to be proviedoperated through button made of delrin p 500. arm pad material shall be polyurethane with 2mm metal insert. nylon base having pcd of660mm five pronged base made up of pa6, 30% glass filled reincforced with bottom ribbing to be provided. 50mm dia twin castors with pa6material to be provided.tolerance of +/- 5mm to be considered for product sizes i.e length, depth & height and tolerance of 5% to beconsidered in pipe thickness & pipe sizes. , the overall size of chair shall be, total height 855mm, width 620mm,depth 550mm, seat depth 470mm seat width 475mm seat to back height440 and back width shall be 460mm. seating height shall be 460mm.seat should be made up of foam pre moulded at 55 kg/m3 density.hardness of 25+ 3kgf at 50% deflection conforming to is 3400. seat shall be uplhostered with micro fabric 100% polyster 180 gsm abrasion >50000 cycles. no flamming or progressive smoldering within one hour of placement of the cigarettes. fire rated fabric confirming to bs en1021 (match) should be used.the back frame design shall be made from 14g bright steel rod in an exclusive profile for sturdiness andergonomic comfort. the steel frame shall be powder coated to 40-50 microns. the back frame shall offered in special mesh finish in black &grey finish. upholstered with an-70 (black) / an-75 (grey) mesh. special design mesh 100% polyester with 320 gsm. abrasion resistance ->50000 confirming to iso 12947-2. chair shall have fixed armrest with size of 190mm made of with nylon 30% gf.the frame shall be made outof erw tubes with 25 mm diameter with 2.1 mm thickness pipe conforming to is 4923. frame shall be welded by co2 welding process foruniform finish conforming to is 816.frame shall offered with powder coat finish to provide an attractive finish. it shall be in black colour. thepowder coating pre-treatment shall carried out with three in one chemical. after pre-treatment process, the components shall powdercoated for better adhesion of paint. the frames shall powder coated with epoxy polyester powder to the thickness of 40-60 microns as per is101 and oven baked at 180.leg bush shall be provided molded with ppcp.tolerance of +/- 5mm to be considered for product sizes i.elength, depth & height and tolerance of 5% to be considered in pipe thickness & pipe sizes., the overall size of the centre table shall be dia 600mm, 450 mm height. the table top shall be made up of 18mm thick prelaminated particleboard of approved shade all the edges of discussion surface shall be provided with machine pressed 2mm thick pvc lipping glued withhotmelt eva glue free from any

Central Government/Public Sector

CTN :39446145

15 Mar, 2025 NA

Mumbai - Maharashtra

Tender For supply of interior work at hr office - and fixing of staircase railing hand rest in wooden , providing and fixing of display storage unit with finished in laminate , providing and making of low ht storage unit finished in laminate , providing and storage unit finished in laminate , providing and fixing tv unit wall paneling finished in laminate as per design , providing and making of staff working desk finshed in laminate finished , providing and making of side runner storage with set of drawers finished in laminate , providing and fixing file stotage unit finished in laminate , providing and fixing fixed partition wall finished in laminate as per design , providing and fixing of paneling finished in laminate , providing and fixing of wall paneling behind staff working design finished in laminate , providing and making branding wall paneling for light finished in paint , providing and making file printer and display storgae unit finished in laminate , providing and making conference tv unit wall paneling with low ht storage unit finished in laminate as per design , providing and making of staff workstation and indoor plant unit finished in laminate , providing and fixing curtain pelmet finished in paint , providing and fixing model display low ht finished in laminate , providing and fixing paneling on wooden ceiling finished in laminate , providing and making of fixed partition wall with sliding door finished in laminate , providing and fixing wallpaper as per design , providing and making directors tv unit wall paneling with low ht storage unit finished in laminate as per design , providing and fixing of display storage unit finished in laminate as per design , providing and fixing of profile glass partition , providing and fixing conference table finished in marble and metal as per design , providing and fixing tv fixed partition wall with door finished in laminate , providing and fixing of file storage shelf finished in laminate , providing and fixing lift duct door finished in laminate , providing and fixing ceiling rafters finished in laminate , providing and fixing fixed partition wall with door finished in laminate , providing and fixing file storage unit finished in laminate , providing and fixing pipe covering finished in acp , providing and fixing new door finsihed in lamiante , providing and fixing vanity counter storage finished in laminate , providing and fixing duct pipe covering finished in acp sheet , providing and fixing mirror , blinds for all areas , hardware fittings handle_knobs_locks_door stoppers_autocloser

Central Government And Public Sector

CTN :39459732

06 Mar, 2025 NA

Nagpur - Maharashtra

Tender For supply of scissor lift table, capacity 500kg of nilkamal model nkslt500yel (or) its equivalent model i n godrej (detailed specification is enclosed in annexure-i) [ warranty period: 30 months after the date of delivery ]

Escalator Spares Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

Central Government And Public Sector

Central Government/Public Sector

Central Government And Public Sector