Latest gearbox assembly Tenders | Government gearbox assembly Tenders

State Government

CTN :45275642

02 Jun, 2026 3.07 Lacs

Serampore - West Bengal

Tender For repairing and overhauling of one no twin lobe air blower assembly and renovation of 2 nos outgoing motor (blower ) feeder of lt pdb with supply, fitting and fixing spares at sludge pump house under swtp, kmda. - supply,installation,testing and commisioning of following items for hoisting system/ blower and gear box as mentioned below as per direction including cost of materials, machinaries , manpower, cutting,machining,aligning,anchoring,welding,finishing,consumables, carriage and all overheads with all leads and lifts complete as per specification (without painting), i) base frame (ms), ii) shaft/pin with key ways made of ss-304, iii) gear& pinion (forged steel), supply and fixing the 3way c.i v grooved pulley with complete mechanism key way suitable to en-24, 60 mm dia/ as per sample of shaft end., a) motor driving, b) blower driving, supply of gear oil as per direction of engineer in charge., supply of grease, supply and delivery of the following bearing (make: skf):, i) 22312e/c3/ as per sample. (for blower), supply and fixing of tough v belts (make: fenner/power boom / v guard/benq/ecodrive) of the following size c 98/ as per sample., supply fitting fixing of ss (aisi304) bolts,nut & washer i) dia 10 mm to 20 mm a) length upto 75 mm, refixing of impeller of blower after dynamic balancing in workshop as per is rule after dismantling the same., dismantling the 25/30 h.p (18.5 kw)//30 h.p squirrel cage motor from its foundation by opening mounting bolts and disconnection of cables from terminal box and open the v belts for repairing purpose (in condition), preliminary checking of the whole motor (lt sq. cage im) and testing of i.r. value, load currents, leakage factor of stator & rotor, terminal lead joints of stator connection ends, insulation of glass fibre terminal bar, double cage rotor end rings and all of motor bars and bar joints, housing of d.e. & nde shield bearing housing etc. before work to detect fault., complete servicing and heat varnishing of 415volt, 3 phase l.t. sq. cage induction motor after cleaning the stator and heating it up periodically and varnishing by dr. beck s graded insulating varnish to obtain stable ir value, cleaning up the rotor, including heating for demoisturisation, lacker coating on the surface of rotor stampings, cleaning and ro priming on the end shield covers, bearing housing and complete the necessary repairing works as per direction of e.i.c.upto 75kw lt sq. cage im ], re fixing the 25/30h.p star/delta squirrel cage motor over its foundation by mean of mounting bolts & nuts, washer complete connection of existing led of cable at the terminal box and wear the v belts with proper alignment in respect to i.d. fan (12000 cu m/hr capacity)/ blower by adjusting the side rail for smooth running., finishing the end of terminal leads by s & f dowells copper sockets properly supplying tapes, petrollium jelly etc. 6 nos.upto 75kw lt sq. cage im., cost of mechanical work viz. shaft truness, checking key way looping of holes grinding and polishing etc. upto 75kw lt sq. cage im., inspection checking/testing and servicing of the existing starter panel, all terminal connection, contactors, relays etc as per desired technical specification including man and minor materials for proper functioning as per direction of eic., supply and fixing of 240/230 volt, 50 hz, t.p., power contactor (make: l & /abb/schneider/ simence/ ge) having contact block of the following range.32-55amp, supply & fixing of 230/240v, led indicating lamp make :ae/kappa/imp) blue/ white color., supply & fixing of 230/240v, led indicating lamp make :ae/kappa/imp) other than blue/ white color., supply and delivery of thermal overload relays (make: l & t/abb/schneider/simence/ ge/minilec) of the following range:a) 0.2-0.33/ 0.3-0,5/ 0.45-0.75, mn2, supply of ammeter selector switch current in each phase with off, 4 pos. 90 angle ofthrow (off-r-y-b) , supply and fixing of analog ammeter ranging

Central Government/Public Sector

CTN :44980530

08 Jun, 2026 NA

Mumbai - Maharashtra

Tender For supply of set of spares for train 18 gear box,one set consisting of 35 items as per attached annexure a.make: medha [ warranty period: 30 months after the date of delivery ]

Central Government/Public Sector

CTN :45030365

29 May, 2026 NA

Cuddapah - Andhra Pradesh

Tender For supply of bonfigloli gear box spares on annual rate contract basis - model-1:model: as55 df p112, code: 1900000950717270002, batch:6/19, v1, i:33:2, application : i) neutralization tank agitator ii) precipitation tanks in chemical house iii) causticization tanks, casing with flange (part no. 2) for model-1, cover (part no. 3) for model-1, internal support (part no. 4) for model-1, gasket (part no. 5) for model-1, gasket (part no. 6) for model-1, extended 1st reduced pinion (part no. 7) for model-1, bored 1st reduced pinion (part no. 8) for model-1, gear wheel 1st reduction (part no. 9) for model-1, gear wheel 2nd reduction (part no. 10) for model-1, pinion 3rd reduction (part no. 11) for model-1, gear wheel (part no. 12) for model-1, cap (part no. 13) for model-1, bored input shaft (part no. 14) for model-1, oil seal (part no. 15) for model-1, oil seal (part no. 16) for model-1, gear head / box, in put assembly, out put assembly, bearing (part no. 20) for model-1, bearing (part no. 21) for model-1, bearing (part no. 22) for model-1, bearing (part no. 23) for model-1, bearing (part no. 24) for model-1, key (part no. 25) for model-1, key (part no. 26) for model-1, key (part no. 27) for model-1, key (part no. 28) for model-1, key (part no. 29) for model-1, level plug (part no. 30) for model-1, drain plug (part no. 31) for model-1, breather plug (part no. 32) for model-1, parallel pin (part no. 33) for model-1, parallel pin (part no. 34) for model-1, hex head screw (part no. 35) for model-1, hex head screw (part no. 36) for model-1, hex head screw (part no. 37) for model-1, circlip (part no. 38) for model-1, circlip (part no. 41) for model-1, circlip (part no. 42) for model-1, 2 nd reduction pinioin (part no. 45) for model-1, out put shaft (part no. 47) for model-1, spacer ring (part no. 48) for model-1, circlip (part no. 58) for model-1, circlip (part no. 39) for model-1, extended input shaft (part no. 50) for model-1, key (part no. 51) for model-1, input assembly, output assembly, model-2:as60 df p112, code: i 11799930001,batch:4/10, v1, i:37:1, application : feed tank agitator - ssr, casing with flange (part no. 2) for model-2, cover (part no. 3) for model-2, internal support (part no. 4) for model-2, gasket (part no. 5) for model-2, gasket (part no. 6) for model-2, extended 1st reduced pinion (part no. 7) for model-2, bored 1st reduced pinion (part no. 8) for model-2, gear wheel 1st reduction (part no. 9) for model-2, gear wheel 2nd reduction (part no. 10) for model-2, pinion 3rd reduction (part no. 11) for model-2, gear wheel (part no. 12) for model-2, cap (part no. 13) for model-2, bored input shaft (part no. 14) for model-2, oil seal (part no. 15) for model-2, oil seal (part no. 16) for model-2, gear head / box, in put assembly, out put assembly, bearing (part no. 20) for model-2, bearing (part no. 21) for model-2, bearing (part no. 22) for model-2, bearing (part no. 23) for model-2, bearing (part no. 24) for model-2, key (part no. 25) for model-2, key (part no. 26) for model-2, key (part no. 27) for model-2, key (part no. 28) for model-2, key (part no. 29) for model-2, level plug (part no. 30) for model-2, drain plug (part no. 31) for model-2, breather plug (part no. 32) for model-2, parallel pin (part no. 33) for model-2, parallel pin (part no. 34) for model-2, hex head screw (part no. 35) for model-2, hex head screw (part no. 36) for model-2, hex head screw (part no. 37) for model-2, circlip (part no. 38) for model-2, circlip (part no. 41) for model-2, circlip (part no. 42) for model-2, 2 nd reduction pinioin (part no. 45) for model-2, circlip (part no. 58) for model-2, circlip (part no. 39) for model-2, extended input shaft (part no. 50) for model-2, key (part no. 51) for model-2, spacer ring (part no. 46) for model-2, out put shaft (part no. 49) for model-2, circlip (part no. 57) for model-2, input assembly, output assembly, model-3:as60 df p132, code:i11800030001, batch:4/10, v1, i:33:4,application : i) filtrate tank

State Government

CTN :45007424

26 May, 2026 1.49 Crore

East Nimar - Madhya Pradesh

Tender For corrigendum : complete overhauling of electrical wire rope hoist along with supply of spares for electrical wire rope hoist installed at coal mill area at 2x600 mw, stage-i, sstpp, mppgcl, dongalia. - scope of service, complete supervision & installation of new spares/replacement of damaged/eroded spares of all 08 numbers of hoist (04 numbers capacity-20 ton & 4 numbers of capacity-15ton)., scope of supply, spares for 20 ton hoist, brake motor 15hpx1000rpm, 40% cdf, 150st/hr, s4 duty, foot mounted sq cage f/s 160 l, terminal box required right side for 15t or 20t hoist make : siemens, brake motor 1.5hpx1000rpm, 40% cdf, 150st/hr, s4 duty, flange mounted sq cage f/s 90 s for ct<, terminal box required top side make : siemens, gear box with coupling for trolley, mdl: ibc162/25.9/200-24 make: premium, gear box with coupling for trolley, mdl: ibc162/18.9/200-24 make: premium, rotary limit switch make: soc, two way lever type limit switch, make: soc, disc brake for 15hp motor, make: - emco, type 14.458, size: - 20, disc brake for 1.5hp motor, make: - emco, type 14.458, size: - 12, cable trolleys medium duty, wheel dia min 40 mm., wire rope 20 mm / 6x36 steel core/ galvanized, make- ushamartin, push buttons with 12 meter cable, rectifier size- eh720hhd, long travel dsl system, i- chain (5 mm)-, ii- cable 6 mm epr, iii- fasteners (1/4x2 ), lt motor shaft, lt motor pinion, spares list of 15-ton hoist, brake motor 15hpx1000rpm, 40% cdf, 150st/hr, s4,duty, foot mounted sq cage f/s 160 l, terminal box required right side for 15t or 20t hoist make : siemens, brake motor 1.5hpx1000rpm, 40% cdf, 150st/hr, s4 duty, flange mounted sq cage f/s 90 s for ct, terminal box required top side make : siemens, gear box with coupling for trolley, mdl: ibc162/25.9/200-24 make: premium, gear box with coupling for trolley, mdl: ibc162/18.9/200-24 make: premium, rotary limit switch make: soc, two way lever type limit switch, make: soc, disc brake for 15hp motor, make: - emco, type 14.458, size: - 18, disc brake for 1.5hp motor, make: - emco, type 14.458, size: - 12, cable trolleys medium duty, wheel dia min 40 mm., wire rope 15 mm / 6x36 steel core/ galvanized, make- ushamartin, pendent push buttons, rectifier size- eh720hhd, long travel dsl system, chain (5 mm)-, cable 6 mm epr, fasteners (1/4x2 ), lt motor shaft, lt motor pinion

Central Government/Public Sector

CTN :45069836

28 May, 2026 NA

Korba - Chhattisgarh

Tender For corrigendum : procurement of spares of piv gearbox for st ii scrapper conveyor ahd ntpc korba - overload coupling,piv,mrhb43, brake band,piv,gear box,mrhb43

State Government

CTN :45272693

11 Jun, 2026 NA

Chandrapur - Maharashtra

Tender For procurement of gearbox and it s spares for clinker grinders in ahp-210mw during u-3 coh at cstps, chandrapur. - ahp basys cg gear box, ahp basys cg gear box spares set, coupl flexible element (part no-36), fluid sm 4 coupling half for gear box si

Central Government/Public Sector

CTN :45213070

01 Jun, 2026 NA

Visakhapatnam - Andhra Pradesh

Tender For corrigendum : tender for supply of spares for elecon make gearboxes of cooling tower fans - cam pn 70 ct16 gear box , plunger pn 71 ct16 gear box , threaded valve seat pn 73 ct16 gear box , steel ball pn 74 ct16 gear box , threaded plug pn 75 ct16 gear box , spring pn 72 ct16 gear box , cam pn 70 ct19a gear box , plunger pn 71 ct19a gear box , threaded valve seat pn 73 ctu200 , steel ball pn 74 ct19a gear box , threaded plug pn 75 ct19a gear box , spring pn 72 ct 19a gear box

Central Government/Public Sector

CTN :44561220

27 May, 2026 NA

Hyderabad - Telangana

Tender For bid to ras corrigendum : tender for supply of supply of spares for hmt fn3h milling machines - spur gear d2775043 , spur gear d2373013 , spur gear d3348833 , spline shaft a3627843 , spline shaft b0034843 , spur gear d1347003 , spline shaft a3014003 , external toothed bush h9580013 , spur gear d9374003 , shifter gear d2075853 , shifter gear d2274893 , shifter gear d2775043 , shifter gear d05070843 , spur gear d0571823 , shifter gear d0552003 , shifter gear d2775033 , spur gear d1347003 , spur gear d2363993 , spur gear d-2373023 , spur gear d2372943 , spur gear d2363983 , spur gear d2353913 , spur gear d2363003 , spur gear d2363973 , spur gear d2373013 , splined shaft for fixed gears a3014003 , splined shaft for shifter gears a3627843 , splined shaft for rapid clutch a3633013 , spur gear d2076013 , spur gear d034381 , spur gear d2363873 , spur gear d2363893 , splined shaft a3036833 , driving disc h9700013 , gear d2077003 , spur gear d9374003 , spur gear d1573003 , disc springs m198143 , spur gear d2354853 , high low gear d5867003 , spur gear d5072003 , splined shaft a3625063 , splined shaft a3036823 , spur gear d0562003 , spur gear d1073003 , longitudinal feed screw rod a5039813 , longitunidal feed box nut b9158803 , bevel gear e0357833 , bevel gear part no.1-e 02 76 81 3 , bevel gear e0357823 , bevel gear part no.1-e 10 78 82 3 , spur gear part no.1-d 23 74 80 3 , spur gear d2356813 , splined shaft a3037823 , splined shaft a3037803 , bevel gear e0357823 , shaft-i a0527803 , bevel gears e9066823 , spur gear a8153803 , shaft ii &iv a0514813 , bevel gear stock no. e1057813 , spur gear d2273803 , longitudinal feed screw rod a5039853 , helical gear d1276013 , longitudinal nut b9158843 , worm wheel e6374823 , handle rod a1614013 , shaft , bush b1573903 , lever b0006001 , lever f71115813 , shift fork f7441013 , spline shaft a3625073 , spline bush b9058813 , spur gear d2356823 , spline shaft a3026873 , spur gear d2371933 , transverse nut d2968803 , transvesre spindle a9038803 , nut b1468803 , spur gear a9430803 , spur gear a906580 , spares for fn-3h milling m/c no1134 spline shaft a3026863 , spline bush b0340803 , spline shaft a3546803 , spur gear d2371813 , spur gear d2371823 , spline shfat a3023803 , spline shaft a3023813 , spur gear d2352003 , spline shaft-v a3034813 , bevel gear eo 354003 , bevel gear e1058003 , coupling bush d1857003 , spur gear d9272803 , spline flange b1773813 , spur gear d9366803 , spur gear d1881013 , spur gear d2362883 , spur gear d3346803 , bevel gear e0355813 , 140 bevel gear (e-0366833) , shaft a2618813 , coupling h0002873 , flange bush b167783 , threaded piece b3227803 , coupling b8247813 , coupling b8445803 , coupling b8553803 , spline shfat a4535803 , spur gear d2363813 , spur gear d2345803 , spline shaft a3026823 , flanged bush b2677803 , bevel gear e0366843 , bevel gear shaft m1449813 , coupling b8553813 , coupling b8574803 , coupling plug m723002 , spline shaft a3024813 , spur gear d 20.72 823 , spur gear d2345833 , worm shaft e7159893 , spur gear stock no. d9045003

CTN :45289717

02 Jun, 2026 NA

Seoni - Madhya Pradesh

Tender For supply of spares for cep suction valves - stem,csv,gv,class 150,size:20",wcb back seat,csv,gv,class 150,size:20", wcb sw gasket,csv,gv,class 150,size:20", wcb gear box,csv,gv,class 150, size:20", wcb

CTN :45311746

30 May, 2026 NA

Panipat - Haryana

Tender For planetary gear box and spares

Gearbox Assembly Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors