Latest gi bar Tenders | Government gi bar Tenders

State Government

CTN :39207416

25 Feb, 2025 9.11 Lacs

Kothamangalam - Kerala

Tender For corrigendum : suppling and fixing gi barbed wire on the existing anti climbing devices of the tower of 66kv feeders under lms moolamattom

Central Government/Public Sector

CTN :39397981

25 Feb, 2025 NA

Nagpur - Maharashtra

Tender For renovation / repairs to 8 nos. toilet (ground floor & 1st floor) of adminstrative building, toilet for studio men ( 1 nos.), exterior painting of front corner of old akashvani building, installation and providing of gi barbed wire around the legs of stl tower at akashvani civil lines, nagpur.

CTN :39335848

07 Mar, 2025 NA

Darjeeling - West Bengal

Tender For supply of assy wheel nut , clutch slave cylinder , dowel sleeve heavy 10x402 , assy clutch pressure plate 310mm dia , assy clutch disc 330 dia , gasket kit cyl head air compressor , assy oil separator , assy gear shift lever knob , stop light switch , gasket , sub assy clutch housing , electric temperature gauge , tempe transducer , starter motor 12v make tvs lucas steel , shifting rod for second and third gear , ball bearing

CTN :39317697

12 Feb, 2025 25.90 Lacs

Multi City - Bihar

Tender For construction of additional class room 2 units at m.s. giridhar barav upper primary school under block navanagar

State Government

CTN :39230408

21 Feb, 2025 47.20 Lacs

Jaipur - Rajasthan

Tender For package-15 - earth work in excavation in foundation, trenches etc. including dressing of sides and ramming of bottoms, including getting out the excavated material, refilling after laying pipe/ foundation and disposal of surplus excavated material at a lead upto 50m suitable site as per direction of engineer for following depths, below natural ground / road top level.depth upto 1.5 m, providing, laying, spreading and compacting of granular sub-base by providing close graded material (table 400-1), spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at omc, and compacting with vibratory roller to achieve the desired density, complete as per mort&h specification clause - 401 including all material, labour, machinery, lighting, guarding and maintenance of diversion.grading - iii material, providing and laying lean cement concrete 1:4:8 in sub- base over a prepared sub-grade with coarse and fine aggregate conforming to is: 383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per table 600-1, cement content not to be less than 150 kg/ cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 mpa at 7 days, mixed in concrete mixer, laid manualy, compacted with surface vibrator, finishing and curing complete as per clause 601, 112 of mort&h specification including all material, labour, machinery, lighting, guarding and maintenance of diversion., providing and laying un-reinforced, dowel jointed, plain cement concrete mix in pavement over a prepared sub base with 43 grade cement, coarse and fine aggregate conforming to is: 383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a batching and mixing plant as per approved mix design, transported to site, laid with a fixed form or slip form paver, spread, compacted and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip, dowel bar, tie rod, admixtures as approved, curing compound, finishing to linesand grades complete as per drawing and as per clause 602, 112 of mort&h specification including all material, labour, machinery, lighting, guarding and maintenance of diversion.pcc m-20 -base of drain work, reinforcement for r.c.c. work at all levels including straightening, cutting, bending, placing in position and binding all complete.mild steel and medium tensile steel bars., centring and shuttering with plywood or steel sheet upto two stories or height upto 7.5 metre above plinth level including strutting, propping etc. and removal of form for :foundations, footings, bases of columns, etc. for mass concrete.

Central Government/Public Sector

CTN :39278481

20 Feb, 2025 NA

Varanasi - Uttar Pradesh

Tender For tender for supply of fabrication - packers plate set (bm-012.06) as per drg. 46191003436/00 with material as per specn. aa10119/15 , splice plate (bm-011.17) as per drg. 46191003616/00 with mal as per specn. aa10119/15 , dowel pin (bm-011.18) dia-38 x 126 long as per drg. 46191003632/00 with matl as per specn. aa10208/07 , dowel pin (bm-011.19) dia-50 x 115 long as per drg. 46121003633/00 with matl as per specn. aa10208/07 , seamless steel pipe od-33.4x3.4 thk x 400 mm long as per specn. aa10455/09 , insert plate (bm-007.08) -- as per drg. 46190002569 rev.00 with matl. as per drg.

CTN :39145039

20 Feb, 2025 NA

Hyderabad-T - Telangana

Tender For supply of taper shank drill flute length 140mm oal 238mm , dia 5.0mm parallel shank drill flute length 52mm oal 86mm , dia 2.0mm parallel shank drill flute length 24mm oal 49mm. , dia 3.0mm parallel shank drill flute length 33mm oal 61mm. , dia 4.0mm parallel shank drill flute length 43mm oal 75mm , dia 4.5mm parallel shank drill flute length 47mm oal 80mm , dia 5.5mm parallel shank drill flute length 57mm oal 93mm , dia 6.0mm parallel shank drill flute length 57mm oal 93mm , dia 6.5mm parallel shank drill flute length 63mm oal 101mm , dia 6.2mm parallel shank drill flute length 63mm oal 101mm , dia 6.4mm parallel shank drill flute length 63mm oal 101mm , dia 7.0mm parallel shank drill flute length 69mm oal 109mm , dia 7.8mm parallel shank drill flute length 75mm oal 117mm , dia 7.5mm parallel shank drill flute length 69mm oal 109mm , dia 8.0mm parallel shank drill flute length 225mm oal 265mm , dia 8.2mm parallel shank drill flute length 75mm oal 117mm , dia 8.4mm parallel shank drill flute length 75mm oal 117mm , dia 8.6mm parallel shank drill flute length 81mm oal 115mm , dia 9.0mm parallel shank drill flute length 75mm oal 117mm , dia 9.2mm parallel shank drill flute length 81mm oal 115mm , dia 9.5mm parallel shank drill flute length 87mm oal 133mm , dia 9.6mm parallel shank drill flute length 87mm oal 133mm , dia 9.8mm parallel shank drill flute length 87mm oal 133mm , dia 10.0mm parallel shank drill flute length 87mm oal 133mm , dia 10.2mm parallel shank drill flute length 87mm oal 133mm , dia 10.4mm parallel shank drill flute length 87mm oal 133mm , dia 10.6mm parallel shank drill flute length 87mm oal 133mm , dia 11.0mm parallel shank drill flute length 94mm oal 142mm , dia 11.2mm parallel shank drill flute length 94mm oal 142mm , dia 11.5mm parallel shank drill flute length 94mm oal 142mm , dia 12.0mm parallel shank drill flute length 101mm oal 151mm , dia 12.5mm parallel shank drill flute length 101mm oal 151mm , hand tap set hss m3 x 0.5 -6h , hand tap set hss m4 x 0.7 -6h , hand tap set hss m5 x 0.8 -6h , hand tap set hss m6 x 1 -6h , hand tap set hss m8 x 1.25 -6h , tap set m10 x 1.5 , hand tap set m12 x 1.75 , tap set m14 , tap set m16 x 2 , tap set m20 , hand tap set hss m24 x 3 -6h , hand tap set hss m30 x 3.5 pitch , dowel pins size dia3 10l hardened steel 55-60 hrc , dowel pins size dia3 16l hardened steel 55-60 hrc , dowel pins size dia5 16l hardened steel 55-60 hrc , dowel pins size dia 4 30l hardened steel 55-60 hrc , dowel pins size dia 4 20l hardened steel 55-60 hrc , dowel pins size dia 4 10l hardened steel 55-60 hrc , dowel pins size dia5 20l hardened steel 55-60 hrc , dowel pins size dia5 40l hardened steel 55-60 hrc , dowel pins size dia5 60l hardened steel 55-60 hrc , dowel pins size dia 6 20l hardened steel 55-60 hrc , dowel pins size dia 6 40l hardened steel 55-60 hrc , dowel pins size dia 8 20l hardened steel 55-60 hrc , dowel pins size dia 8 30l hardened steel 55-60 hrc , dowel pins size dia 8 50l hardened steel 55-60 hrc , dowel pins size dia 8 75l hardened steel 55-60 hrc , dowel pins size dia 10 20l hardened steel 55-60 hrc , dowel pins size dia 10 30l hardened steel 55-60 hrc , dowel pins size dia 10 75l hardened steel 55-60 hrc , dowel pins bid details/ 2 / 81 size dia 10 50l hardened steel 55-60 hrc , dowel pins size dia 12 20l hardened steel 55-60 hrc , dowel pins size dia 12 40l hardened steel 55-60 hrc , dowel pins size dia 12 50l hardened steel 55-60 hrc , dowel pins size dia 16 25l hardened steel 55- 60 hrc , dowel pins size dia 16 50l hardened steel 55-60 hrc , dia 3.0mm parallel shank reamer flute length 31mm oal 61mm , dia 4.0mm parallel shank reamer flute length 42mm oal 75mm , dia 5.0mm parallel shank reamer flute length 56mm oal 86mm , dia 6.0mm parallel shank reamer flute length 56mm oal 93mm , dia 8.0mm parallel shank reamer flute length 74mm oal 117mm , dia 10.0mm parallel shank reamer flute length 86mm oal 133mm , dia 12.0mm parallel shank reamer flute length 104mm oal 151mm

Gi Bar Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

State Government

Central Government/Public Sector

State Government

Central Government/Public Sector