Latest gi fitting Tenders | Government gi fitting Tenders

State Government

CTN :43117006

17 Dec, 2025 NA

Delhi - Delhi

Tender For procurement of hardware items for day to day maintenance of various tube wells installed in 185 and 186 under okhla constituency ac-54. - supply of tail piece of the medium class gi pipe 500 mm long with one end threaded as per outlet of pump & another end flanged of size (120 mm dia.) of gi pipe.make of pipe:- tata / jindal(a) 50mm dia., (b) 40mm dia., supply of ms clamp of 600 mm length duly fabricated form 12.5 mm thick 75 mm wide m.s. plate for holding the g.i pipe of sizes:(a) 50mm dia., (b) 40mm dia, fabrication and supply of g.i. 90 bend having flange at both ends (heavy duty). of following sizes:(a) 50mm dia., (b) 40mm dia., fabrication and supply of bore cover approx size lx1 made out from 6mm thick m.s. sheet in 2 halves & a circular hole in centre 3-1/2" dia. with locking arrangement by nuts & bolt., supply of ms full threaded nut bolts off sizes., supply of rubber packing (a) 50mm dia flange, (b) 40mm dia flange

State Government

CTN :43117029

17 Dec, 2025 NA

Delhi - Delhi

Tender For sic of submersible pump set and all allied e/m equipment for rebored tube well near h.no.-116c shahpur jat in greater kailash constituency ac-50. - supply of submersible pump set fitted with dynamically balanced ss impeller mounted on stainless steel shaft with protection sleeve having stage bowl & closed grained shorted type impeller, the pump will be directly coupled to required wet type induction motor of 7.5 hp, 10 stage, speed 2900 rpm suitable for operation of 3 phase, 415 volt, 50 hz, ac supply with efficiency 70% at following duty point:200 lpm on 90 mtr. head. having discharge outlet 50 mm and outside dia 142 mm.make: bs/skope/ any djb approved make, supply of hut type electrical feeder pillar / fabricated with 50 x 50 x 6mm angle iron and 16 swg ms sheet with horizontal and vertical intermediate member of suitable size. i.e. 1370 mm x 760mm x 460 mm. with arrangement for mounting of switchgear and electrical energy meter i.c. painting heaving following item fitted.a) mccb 63 amp, 4pole, 415volt, 35 ka -1 no.b) rccb 63 amp, 4pole with earth fault indication protecting a circuit automatically in the event of earth leakage sensitivity 100ma, - 1 noc) fully automatic star delta starter of relay range 13-21 amp. (7.5 hp to 10 hp) 3 phase oil immersed type -1 no.d) ampere 96 x 96 mm. square shape 0-30 amp-1 no.e) voltmeter 96 x 96 mm. square shape 0-500 volt-1 no.e) indicating lamp (a set of 3 lamps) 1.setf) shunt capacitor of 10 kvar mpp type with three phase isolator with suitable bankingg) motor protection assembly with earth leakage protection phase sequence corrector, single phasing, protection, overload protection, high voltage / low voltage protection time delay power on, programmable time switch i.c. r&b phase facility to change over from automatic, to manual &vice verse for up to 10 h.p -01 nos. complete wiring & installation of above accessories with required copper conductor wire and thimble etc. 01 job.make of all components: any djb approved., s/o pvc insulated & pvc sheathed cable with plain copper conductor having 3 phases, 3 core flat for submersible motor of 4 square mm size each 100 mtrs.make:grandlay / havells./any djb approved make, s/o m.s. clamp of 600 mm length duly fabricated out of 12.5 mm thick 75 mm wide, m.s. plate for holding the pipe of 50 mm dia., s/o double flange gi column pipe 50 mm dia medium class each of 3 mtrs long duly threaded on both ends, welded fitted with gi flange on both ends with slot of submersible cable. make: tata/ jindal./any djb approved make, s/o/ tail piece of the medium class gi pipe 500 mm long with one end threaded as per outlet of pump & another end flanged as per size of gi pipe 50 mm dia., s/o gi 90 bend of size 50 mm dia having both side flange (heavy duty)., s/o nut & bolts of 1/2 dia of different size i.e. 1.5 dia& 2.5 long full threaded., s/o rubber packing for 50 mm dia flange., fabrication and supply supply of bore cover approx size 8-10 inch diameter made out from 6mm thick m.s. sheet in 2 halves & a circular hole in centre 3-1/2 dia. with locking arrangement by nuts & bolt., earthing with g.i. earth pipe 4.5 meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required., providing and fixing 6 swg dia g.i. wire on surface or in recess for loop earthing as required., installation of t/well by lowering of sub p/set with all allied above items. this includes installation and grouting of panel boards with all electrical wiring & cabling at site. all tools & tackles i/c. tripod chain pulley blocks etc. shall be arranged by the firm. this includes testing & commissioning of t/well on load at site i/c. cartage, loading & unloading of material. it also includes a trial run of 30 hrs operation successfully by the firm. all required civil work included in the scope of work.

State Government

CTN :43117042

17 Dec, 2025 NA

Delhi - Delhi

Tender For procurement of hardware items for day to day maintenance of various tube wells installed in ward no-180 and 181 under badarpur constituency ac-53. - supply of tail piece of the medium class gi pipe 500 mm long with one end threaded as per outlet of pump & another end flanged of size (120 mm dia.) of gi pipe.make of pipe:- tata / jindal50mm dia., supply of tail piece of the medium class gi pipe 500 mm long with one end threaded as per outlet of pump & another end flanged of size (120 mm dia.) of gi pipe.make of pipe:- tata / jindal 40mm dia., supply of ms clamp of 600 mm length duly fabricated form 12.5 mm thick 75 mm wide m.s. plate for holding the g.i pipe of sizes:50mm dia., supply of ms clamp of 600 mm length duly fabricated form 12.5 mm thick 75 mm wide m.s. plate for holding the g.i pipe of sizes: 40mm dia., fabrication and supply of g.i. 90 bend having flange at both ends (heavy duty). of following sizes:50mm dia., fabrication and supply of g.i. 90 bend having flange at both ends (heavy duty). of following sizes: 40mm dia., fabrication and supply of bore cover approx size lx1 made out from 6mm thick m.s. sheet in 2 halves & a circular hole in centre 3-1/2" dia. with locking arrangement by nuts & bolt., supply of ms full threaded nut bolts of sizes., supply of rubber packing 50 mm dia pipe flange, supply of rubber packing 40 mm dia pipe flange

Central Government/Public Sector

CTN :42825220

17 Dec, 2025 NA

Kurukshetra - Haryana

Tender For corrigendum : supply of sanitary and public health items d d -brass peet valve , brass ball cock , brass pillar cock face , brass spindle , brass nut for steel sink waste , c.p. bottle trap , c.p. concealed stop cock , g.i. elbow , g.i. elbow reducer , g.i elbow reducer , g.i. nipple , g.i. pipe , g.i. socket , g.i. tee , g.i. union , tanki nipple , pvc connection , pvc ld flushing cistern complete set of capacity 10 ltr , pvc elbow 3 inch , pvc elbow 4 inch , pvc ball , pvc short bend 32mm , pvc long bend 32mm , pvc waste pipe , pvc water tank 3 layer with cap , pvc hinges for ewc seat cover , pvc washer for pvc connection , pvc washer for spindle , pvc washer , pvc washer for ewc seat , pvc water tank cover , pvc handle for ld cistern , pvc solvent solution , ptmt angel valve , urinal channel chinaware , chinaware urinal seat pot small , chinaware urinal partition , wc seat orissa pattern , chinaware ewc seat , wash hank basin chinaware , steel sink waste square , cp grating 5 inch dia with double frame plain , soot gola , steel screw 3 inch , m.s. nut bolt , m.s. nut and bolt , c.i. hr bend 3 inch , c.i. hr bend 4 inch , c.i. hr gully trap 4 inch , c.i. floor trap 3 inch ) /bid number : gem/2025/b/6905242 * /dated: 19-11-2025 & & / bid document 1 / 50

State Government

CTN :43109692

18 Dec, 2025 2.03 Lacs

Bilaspur (Hp) - Himachal Pradesh

Tender For restoration of rain damages of lwss sair dobha karot in tehsil sadar district bilaspur (sh: providing wheel valve andf gi fitting of various dia for distribution system)undere jsv section jukhala).

State Government

CTN :43116877

18 Dec, 2025 4.98 Lacs

Mandi - Himachal Pradesh

Tender For a/r & m/o of lwss malwana bhadyal in gp bhadyal in tehsil balh distt. mandi (h.p). (sh:- providing and supplying of gi fitting of various dia under jal shakti section gagal, sub division baggi no.ii). rs. 498531 /- only

Corporations And Associations And Others

CTN :43117081

17 Dec, 2025 67.97 Lacs

Delhi - Delhi

Tender For supply and installation of open gym equipments in najafgarh zone and central zone under mplads funds for various locations of parks in municipal corporation of delhi. - supply and installation of open gym equipments in najafgarh zone and central zone under mplads funds for various locations of parks in municipal corporation of delhi., seated puller /pull chair made from c class g.i pipe. dimensions: - 1900mm (length) x 740mm (width) x 1920mm. (height). safe area:- 1.2mtr x 3mtr. seated puller equipment made up of c class g.i. pipe of different nb.nb stands for nominal bore sizes i.e. internal diameter of pipe in millimeters. the center pipe is of 100nb made from c class g.i. pipe. bottom support is of m.s. round plate of dia 250 mm & 10mm thickness welded. all linkages are made up of 25nb c class g.i. pipe. the handle frame is of 32nb c class g.i. pipe. the seat frame is of 32nb c class g.i. pipe. to build structure bushes are used which are made from seamless pipe of 60mm o.d. and 5mm thickness as well as 60mm diameter solid bar bush used. the foundation used for fixing is a structure and made from center pipe of g.i. of 80 nb c class. welded with m.s. round plate of dia 250 mm & 10mm thick. main pipe supported with 25 mm x 25mm m.s. angles of 3 mm thickness and 20mm x 40mm crc square pipes of 3mm thickness. foundation cover closing cap is made from injection moulded plastic lldpe / hdpe. the seats and back rests are fitted on the outer frames are made up of m.s. sheet of size 330 mm x 300 mmx2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges.closing caps are made up of from injection moulded plastic lldpe / hdpe.pins used of diameter 25mm and 17mm are made up from sae 8620 bright material. the bearings used are of 6205 2rs1 and 6203 2rs1 permanent lubricated sealed bearing of reputed brand.high tensile steel with galvanized nuts & bolts are used for assembly.thecirclips used for assembly are of a16. the gym equipment shall be finished smooth with a primer coating of atleast 40 micron followed by epoxy based powder coating with polyster powder coating of at least 60 to 70 micron thickness using exonobel / berger make paints or its equivalent paints. the holding down/fixing of gym equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size)., cross trainer /elliptical exerciser dimensions: - 1320mm (length) x 600mm (width) x 1750mm. (height). safe area: - 1.77 x 1.2mtr. cross trainer equipment made from c class g.i. pipe of different nb.nb stands for nominal bore sizes i.e. internal diameter of pipe in millimeters. the main frame pipes are of 80nb c class g.i. pipe with single bend pipe with 250mm radius. the bottom support of m.s. round plate of dia 250 mm & 10mm thick. the handle frame is made up of 25nb c class g.i. pipe. the foundation used for fixing is a structure and made from center pipe of g.i. of 80 nb c class welded with m.s. round plate of dia 250 mm & 10mm thick. main pipe supported with 25 mm x 25mm m.s. angles of 3 mm thickness and 20mm x 40mm crc square pipes of 3mm thickness. to build structure bushes are used which are made from m.s. seamless pipe of 60mm od with 5 mm thickness. the footrests are made from injection moulded plastic lldpe / hdpe. closing caps are made up of injection moulded plastic lldpe / hdpe. pins used of diameter 35mm, 25mm, and 17mm are made up from sae 8620 bright .the bearings used are of 6007 2rs1 62052rs1 and 62032rs1 permanent lubricated sealed bearing of reputed brand. high tensile steel with galvanized nuts and bolts are used for assembly. the gym equipment shall be finished smooth with a primer coating of atleast 40 micron followed by epoxy based powder coating with polyster powder coating of at least 60 to 70 micron thickness using exonobel / berger make paints or its equivalent paints. the holding down/fixing of gym equipments shall b

State Government

CTN :43110072

26 Dec, 2025 10.00 Lacs

Jabalpur - Madhya Pradesh

Tender For supply of hardware/ sanitary material and building materials, various units at ndvsu, adhartal, jablpur (3rd call) - supply of hardware/sanitory building material all item should be isi mark enclosed list, pvc pillar cock , pvc engle cock , brass short body bib tap faucet with wall flange water tap for bathroom, kitchen, wash basin, hot & cold water compatible, chrome finish( ) short body, tri water tap for bathroom | hold and cold mixer faucet | wash basin tap with water saving hidden aerator | strong brass construction, brasspillar cock , brass engle cock , stainless steel long body taps for bathroom and kitchen taps with chrome finish and quarter turn fitting ( ) long body, pvc long body bib tap with wall flange hot & cold water faucet for kitchen sink, bathroom & wash basin | durable, rust- free plastic tap for indoor use ( ) long body, pvc short body bib tap with wall flange hot & cold water faucet for kitchen sink, bathroom & wash basin | durable, rust-free plastic tap for indoor use ( ) short body, wash basin pipe (heavy ), connection pipe ( 1 feet ), connection pipe ( 2 feet ), upvc socket - , upvc t bend - , upvc brass l bow - , upvc brass socket - , upvc brass t bend - , upvc l bow - 1 , upvc socket - 1 , upvc t bend 1 , upvc brass l bow - 1 , upvc plan l bow - , upvc brass l bow - 1 , upvc 1 y reducer, upvc brass socket - 1 , upvc plan l bow - 1 inch, upvc brass t bend 1 , upvc brass l bow - 2 , upvc brass socket - 2 , cpvc brass l bow - , cpvc brass socket - , cpvc l bow - 1 , cpvc brass l bow - 1 , cpvc brass socket - 1 , cpvc brass t bend 1 , cpvc brass l bow - 2 , cpvc brass socket - 2 , cpvc brass t bend 2 , g.i. nozzle - 1 , g.i. nipple - 1 , g.i. stopper - 1 , g.i. - t - , g.i. l bow - , g.i. nipple - , g.i. socket - , tapelone, solvent upvc 100gms. box, gate valve brass - , section clamp 3 , section clamp 2 , upvc pipe 1 , upvc pipe1inch, upvc pipe1.5inch, upvc pipe 2 , taparia 500 gms ball pein hammer with handle, pipe pana - 300mm, pipe pana - 600mm, pach pana - 300mm, pechcus - screw driver ( four head ), brass f.t. upvc , brass f.t. upvc 1 , brass m.t. upvc , brass m.t. upvc 1 , cement, brick fly ash 50kg/cm2, bricks open bhatta 25kg/cm2, steel nails - 2 , steel nails - 3 , nittle screws - , nittle screws - 1 , nittle screws 1 , nittle screws , nittle screws 2 , emulsion interior -, painting brush - 2 , painting brush - 3 , painting brush - 4 , painting brush - 6 , putty jk / birla, putty jk / birla, steel fly proof mesh, teak wood beat - , teak wood beat - 1 , teak wood beat - 1 , teak wood beat - 1 , teak wood beat - 2 , ply water proof - 8mm, ply water proof - 10mm, ply water proof - 12mm, ply water proof - 18mm, steel hinges butt - x 3 , steel hinges butt - 1 x 4 , tower bolt steel - 6 , tower bolt steel - 10 , godrej door lock medium size, almira lock, upvc l bow - , cpvc l bow - , cpvc socket - , cpvc t bend - , cpvc socket - 1 , cpvc t bend 1 , g.i. hose collar, floor jali - steel 4 , hexa blade, hammer bit - 6mm, upvc pipe , upvc pipe 1 , cpvc pipe , cpvc pipe 1 , cpvc pipe 1 , cpvc pipe 2 , patti pana - ( nub. 5 to 16 nub. ), ring pana - ( nub. 5 to 16 nub. ), steel nails - 1 , emulsion exterior -, marble - powder, lime - un ., l drop steel - 10 , l drop steel - 12 , tower bolt steel - 8 , steal paint, primer iron, primer wooden, sistan set, health fuset 1 meter, jet spray 1 meter, brass plier cook, brass pliers cook high neck, concealed wall brass inch, universal tool kit with bag/box complete set (plumber), bubble level, metric adjustable tap die inch, tap die inch, tap die 1 inch, tap die 1.5 inch, tap die 2 inch, tap die 2.5 inch, tap die 3 inch, hdpe roll pipe isi 1 inch, hdpe roll pipe isi 1.5 inch, hdpe roll pipe isi 2 inch, hdpe roll pipe isi 2.5 inch, hdpe roll pipe isi 3 inch, hdpe roll pipe isi 4 inch, pcn tell 2 y 2.5 inch, spn 2 inch, horse collar 1inch, horse collar 1.5inch, horse collar 2inch, horse collar 2.5inch, horse collar 3 inch, horse collar 4inch, g.i.

CTN :42822890

12 Dec, 2025 7.57 Lacs

Belgaum - Karnataka

Tender For bid to ras supply of setup of lan at new klp : : - patch cord 2 mtrs bracket lc to lc connector bracket , patch cord 2 mtrs bracketsc e2k bracket , patch cord 2 mtrs bracket e2k to e2k bracket , patch cord 2 mtrs bracket e2k to lc connector bracket , ip bottle , ofc joint closer , splicing paper , pipe gi 3 inch , mcv tripper 16 amp , io box with female rj 45 connector , rj 45 connector 100 per pkt , lan switch 8 port unmanned , lan switch 16 port unmanned , lan switch 24 port unmanned , rack u bracket junction box bracket , crimping tool , casing oblique capping 3 inch x 3 inch , casing oblique capping 1 inch x1 inch , l bend 3 inch x 3 inch , strait cover 3 inch , corner bend 3 inch , three way 3 inch , l bend 1 inch x 1 inch , corner bend 1 inch , strait cover 1 inch , three way 1 inch , screw 1 inch , gitti 1 inch , utp cable cat 6 bracket 305 mtrs bracket , earthing , sitc incl manpower support and installation

CTN :43116367

19 Dec, 2025 NA

Mathura - Uttar Pradesh

Tender For supply of gi fittings -bend gi 15 mm , bend gi 20 mm , bend gi 25mm , bend gi 40mm , bend gi 50mm , bend gi with socket 15 mm , bend gi with socket 20 mm , gi elbow 15 mm , gi elbow 20 mm , gi elbow 25 mm , gi elbow 40 mm , gi elbow 50 mm , gi socket 15 mm , gi socket 20 mm , gi socket 25 mm , gi socket 40 mm , gi socket 50 mm , gi tank nipple 15mm , gi tank nipple 20mm , gi tank nipple 25mm , gi union 15 mm , gi union 20 mm , gi union 25 mm , gi union 40 mm , gi union 50 mm , hex nipple 15 mm , hex nipple 20 mm , hex nipple 25 mm , nipple gi 15 mm x 50mm long , nipple gi 15 mm x 75mm long , nipple gi 15 mm x 100mm long , nipple gi 15 mm x 150mm long , nipple gi 15 mm x 200mm long , nipple gi 20 mm x 50mm long , nipple gi 20 mm x 75mm long , nipple gi 20 mm x 100mm long , nipple gi 20 mm x 150mm long , nipple gi 20 mm x 200mm long , nipple gi 25 mm x 50mm long , nipple gi 25 mm x 75mm long , nipple gi 25 mm x 100mm long , nipple gi 25mm x 150mm long , nipple gi 25 mm x 200mm long , nipple gi 40mm x 100mm long , nipple gi 40mm x 150mm long , nipple gi 50mm x 100mm long , nipple gi 50mm x 150mm long , plug gi 15 mm , plug gi 20 mm , plug gi 25 mm , plug gi 40 mm , plug gi 50 mm , r elbow gi 15 x 20 mm , r elbow gi 15 x 25 mm , r elbow gi 20 x 25 mm , r elbow gi 20 x 40 mm , r elbow gi 20 x 50 mm , r elbow gi 25 x 50 mm , r elbow gi 40 x 50 mm , r socket 15 x 20 mm , r socket 15 x 25mm , r socket 20 x 25mm , r socket 20 x 40mm , r socket 20 x 50mm , r socket 25 x 20mm , r socket 25 x 40mm , r socket 25 x 50mm , r socket 40 x 50mm , r tee gi 15 x 20 mm , r tee gi 15 x 25 mm , r tee gi 15 x 40 mm , r tee gi 20 x 25 mm , r tee gi 25 x 20 mm , r tee gi 40 x 20 mm , tee equal gi 15 mm , tee equal gi 20 mm , tee equal gi 25 mm , tee equal gi 40 mm , tee equal gi 50 mm , gi pipe 15 mm dia med grade , gi pipe 20 mm dia med grade , gi pipe 25 mm dia med grade , gi pipe 40 mm dia med grade , gi pipe 50 mm dia med grade , gi pipe 80 mm dia med grade , cp elbow operated pillar cock , cp bib cock 2 in 1 size 15 mm //bid details2 / 123

Gi Fitting Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors