Tender For supply of welding socket unit of dimension 380(l)x650(w)x300(d) duly housed in outdoor made of high quality thermoplastic polycarbonate pc gfs (shock proof,weather pr oof, rust free, fire retardant, high impact against mechanical load) and should have degre e of ingress protection ip 65 as per iec 60529 to perform under ambient temperature - 35 deg c upto +80 degc. type of mounting: tubular pole mounting, mounting sheet material/canopy should be made of hot dip galvanized iron flat sheet material with thickness shall not be l ess than 2mm and ms flat frame (32x6)mm to be welded on gi sheet. the welding socket unit should comprisisng of the following items. 1.) copper bus bar (r,y,b,n) of each bus bar dime nsion (30x10)mm rating range 100-200amps, and separate earth strip confirmed to is 1897:200 8 or lastest.2.) 63amps 4pole residual current circuit breaker with operating volt age of 41 5volts, 50hz, tripping range : 30ma 3.) 63amps 4pole (3p+n) miniature circuit breaker with ope rating voltage of 415volts, 50hz, breaking capacity range : 10/16/25 ka 4.) 20amps 2pole (p+n) miniature circuit breaker with operating voltage of 230volts, 50hz, breaking capacity range : 10/16/25 ka (all rccb and mcb confirming to is/iec 60898-1:2002 or latest with isi mark), pref ferable make: legrand, havells, schneider, hager, l&t.5.) 63amps 5pin (3p+n+e) and 20amps 3p in (p+n+e) industrial welding socket (with spring supporting door) and suitable plug worki ng on 415volt ac supply, 50hz, of degree of protection ip 67 are designed as per iec 60309-1 and 60309-2, preferable make: schneider, hensel-walther, cape. 6.) 4runs of 16sqmm cu. frls wire. (each r,y,b,n) from copper bus bar to rccb (incomer), 4runs of 16sqmm cu. frls wire fr om rccb (outgoing) to 63amps mcb (incomer), 2runs of 6sqmm cu. frls wire from rccb (outgo ing) to 20amps mcb (incomer), 5runs of 16sqmm cu. frls wire from 63amps mcb(4runs) & green wire from earth strip(1run) to 5pin industrial socket and 3runs of 6sqmm cu. frls wir e from 20amps mcb(2runs) & green wire from earth strip(1run) to 3pin industrial socket. co pper wire confirmed of is 694:2010 or latest. preferable make : anchor, orbit, havells, polyc ab 7.) including cable gland (size confirming by consignee) for loop-in and loop-out of 4cx1 20sqmm ltug cable entry/exit from bottom conform as per en 60423 or latest. din rail for s uitable installations of all rccb and mcb upto 63amps.the manufacture should submit all t est certificate in accordance with latest iec standards. make / brand : cape consisting of 1) emp ty enclosure and mounting flange - spelsberg 2) plug and sockets 63 a/16a ? cape 3) rccb & mcb - l&t 4) conical support - powermat 5) end clamp - connect well 6) earth cable gland with locknut - trinity 7) rep uted make for miscellaneous items like copper bus bar, double compression cable gland, distribution win dow, earth busbar, ms hot dipped canopy, din rail, wiring, screws, nuts, bolts and lugs & other accessori es. hsn code 8537 1000. [ warranty period: 30 months after the date of delivery ]
Tender For bid to ras supply of reapir of mt vehicals - engine mounting front , engine mounting rear , old mounting removing and new mounting fitting and testing labour charge , rotary pump repair and service with parts , nozzle , cam plate , td piston , service kit , tappet roller , pump stripping service above parts firing and pump assembled and calibrating computerised machine , engine push rod , tappet seal , rotary pump removing the vehcile and after service and pump and fitting all dismantling fuel connection fitting and full tappet adjust and vehicle starting and testing labour charges , positioner , tappet toller , tensioner , pump removing the vehicle and after service pump fitting and all calibrating and testing with computerised machine , gear box assembly dismatching and clutch plate pressure plate removing and gear box clutch system full service and reassembled and fitting and vehicle , release bearing , suspension bush , master cylinder asembly removing and full service and fitting the vehicle , fuel pump motor , shock absorber removing and service and fitting , butter front , oil seal set 6 nos , spark plug , nut bolt and washer , door catch , front brake pad removing service and fitting , rear brake lining , petrol filter , air filter , clutch cable fitting , oil pump assembling fitting , joint coupling with bearing , joint star removing service and fitting , silencer packing , wheel bearing front , rear brake bearing , seat cover full change and new making with good quality pvc cloth and foam and fitting the vehicle , suspension full lathe machine work , front pump assembly , full electrical system checking and service , tail light and side indicators , bonnet mirror and side mirror , power window checking and switch replace and system checking , full machine parts removing and above mentioned parts one by one all fitting and checking and road testing labour charge , ac checking and full service and gas filling and testing
Tender For supply of bush upper arm lh and rh , bush lower arm lh and rh , shock absorber front lh and rh , bush stabilizer bar , link stabilizer lh and rh , kit link stabilizer , outer ball joint steering lh and rh , inter shaft lower steering assy , rear shock absorver lh and rh , leaf spring bush rear lh and rh , centre bolt no 16 , u bolt clamp with nut and washer , leaf spring no 4 , ball joint assy upper lh and rh , rubber rebound stopper ifs2wd , shock absorver bush kit lh and rh , rear axle bearing deep groove ball , oil seal inner axle shaft , washer lower arm assy , bolt hex mi4x1 5x113x8 8 lower arm , nut hex mi4x1 5x1 5x6 lower arm , rear axle oil seal outer axle shaft , shim wheel end , sleeve axle shaft , collar locking , bearing carrier , wire ring dgbb dia 398 , concentric slave cylinder bleeder , concentric slave cylinder clutch , clutch disc assy , clutch cover assy , nut nyloc m12x1 25x12x5xgr , nut hex nyl fl m10x1 25x13 5x8 , mounting rear shafter , insulator trans rr mtg eagle 2wp , nut hex hd m12x15 steering ball joint , bushing strut bar , collar strut bar , dendrite , shaft upper arm , fog lamp with bulb lh and rh , abs sensor front left side wheel with cable , rust spray big size , fuel float unit with trf , head light bulb , head light relay , door lifting machine handle , disc cutter 4 inch ) /bid number : gem/2025/b/6452988 * /dated: 15-07-2025 & & / bid document 1 / 36
Tender For supply of maruti veh spare parts f f - piston with pin and circlip , piston ring set std , cylinder linner std , bearing crank shaft rs1 , engine oh gaskit complete with cylinder head gaskit , seal crank shaft front , seal crank shaft rear , seal valve inlet and exhaust , valve inlet and exhust mpfi , water pump assy , oil pump assy , timing belt , fan belt , tensioner assy , temperature sending unit , thermostate valve , clutch plate , pressure plate , clutch release bearing , bearing input shaft , seal cam shaft , spark plug , fuel filter , air filter , oil filter , suspention bush kit complete , shocker assy front , tie rod assy , speedometer head assy , fuel pump , cable hand brake , idle motor , throttle body assy , brake light switch , ignition coil , ignition coil ht lead , injector assy , brake booster with master cylinder assy , wiper blade , water reservior , side view mirror both side , trim pad both side , door lock inner outer , radiator assy with cap , rear fander , engine mounting both side , wheel cylinder rear , rear brake shoe set , front brake disc pad , radiator fan cover , shock absorber rear , mat front and rear , cover timing plastic , tappet cover gasket , acc cable , speedometer cable , clutch cable , uj cross , gear box mounting , clear for paint shiner , filter gas moudulator , cotter valve , cr bush std , brush gear assy , bendix pinion , self carbon bush , crank sensor , frt left shock absorber , frt left suspension arm with bush , ball joint suspension arm , fuel gauge tank , fuel pump assy , timing chain set , timing adjuster , fuel injector , packing throttle body , fuel pipe tank to filter , fuel retun pipe , solenoid switch , release bearing , engine mounting , brake shoe rear , brake disc pad , front leaf spring assy , rear left spring assy , battery terminal positive and negative , suspension bush kit , centre bolt , wheel cylinder , king pin set , ac filter , disc pad , brake shoe set //bid details 2 / 94
Tender For supply of voltmeter, analog, range: 0-1000v ac, size: 72 mm x 72mm square, panel mounting type, provided with mounting accessories and rubber gas ket for shock absorbing, insulation: class-1, accuracy class: 1.5% or better, conforming to is: 1248 (part-1 & 2) -2003 or latest, suitable to use in switch board cabinets of lhb ac coaches, as per sl.no.15 of bill of material of rdso specification no. rdso/pe/spec/ac/0184- 2015 (rev.1) or latest. the voltmeter shall b e similar to model no. sr-72 of m/s. yokins. approved makes: yokins / ae / muller + zeigler / rishabh /l&t or any other rdso-approved makes. [ warranty p eriod: 30 months after the date of delivery ]