Tender For supply of kbl make pump spares - brg housing, brg housing, bearing, journal, clamping plate, shaft seal, shoulder ring,kbl, bearing housing de, bearing housing, o' ring for insert, insert,kbl, impeller, pump shaft with key, imp. wear ring, sets of gasket, impeller, o' ring, complete pump without motor, bare pump assembly,model-kpds, bare pump assembl, sleeve, shaft part no:311, bush, stuffing box moc: astm a276 tp 31
Tender For procurement of spares for bhel make esp type 4xfaa 10x37.5m 2x112150 2 required during aoh of u 1 at 2x600 mw sstpp mppgcl dongalia - plain bearing, outer arm for collecting rapping, shaft insulator assembly, shock pads, clutch and coupling set for cerm shaft, set rings for cerm rapping shaft, pin wheel small, outer arm for emitting rapping, support insulator, shaft sleeve for cerm rapping shaft, pin wheel big, bush bearing assembly for eerm vertical shaft, emitting electrodes 150 hnom pgma 79415, inner arm (clamps) along with fastener moc - en8, bearing no. 1211k with sleeve , make skf/fag/timkan/nbc/insk or equivalent, grip coupling for eerm 1 set = 2no
Tender For supply of rivet copper csk hd 5 into 50mm , block sliding block locating , spring helical compression , plunger locking plunger detent , bushing sleeve front bushing sleeve , lever cocking , spring inner spring helical compression , stud actuating pin straight treated , screw machine retaining screw grub , leather strip 60mm width 3 point 5mm thx190mm long , washer leather set washer special , gasket , bearing ball single thrust 25mm i oblique o x 42mm oblique d x 11mm width , brg ball thrust single row deep groove 24x47x12mm , rivet tubular csk hd 120 deg brass 5x20mm , bellow rubber , brg needle roller journal 22 point 1x35x22mm , clamp hose size 75mm , clamp hose size 45mm , felt mechanical performed , pin anchoring pin pintl , screw csk head screw machine , pad cushioning , rivet solid csk hd 90 degree copper 4x30mm , strap leather , bush tie rod bushing machine thread , seal plain seal plain encased , bearing tapered roller 45 point 242x77 point 788x19 point 842mm width , bearing tapered roller 57 point 15x97 point 63x24 point 608 width , spring helical extension spring helical compression , complete brake lh nsn petrol , complete brake rh nsn petrol , kit lining set 1oblique 32 inch oblique s , spring cylinder end , spring abutment end , wheel cylinder lh and rh , dust cover , hp hose front , 3 way , master cylinder assembly , pipe assy 3 way to front lh hose , pipe master cylinder to 3 way pipe assembly , push rod , d ring , ring , clamp with strap assy precision 6 point 6 phosphated m6x6mm long , bush stablizer premier pad mini , spring torsion , pin taper type a 5x25mm , pin shoulder headless , chain welded , washer fibre , ring retaining ) /bid number : gem/2025/b/6741400 * /dated: 30-09-2025 & & / bid document 1 / 40
Tender For corrigendum : tender for supply of fuse series psc type 6 6 urd 30 tt f 0200 , stainless steel lock tab washer dn6 , o ring 5330bb 10x1 8 20a8 , stop , adjusting shim , stainless steel lock tab washer dn27 , seal ui 480/528x22 , hydrauxim valve 10 2 , spring , axis , sealed valve isolating ring , gasket 20x10x2 , lock washer 95x58x1 5 , gasket 81x64 th 3mm , o ring package electronics housing cover , o ring package electronics housing module , o ring package process flange , tricoclair pipe d 7 13 , tricoclair pipe d 10 16 , impeller nut 29 , mechanical seal type u2ek 0550 9kay 93 , o ring 8 00x2 65 64c8 , parallel key shape a 6x6x28 xc48 , interface gasket set , folded removable filter , relay 2rt10a 28vcc , connector retention clip v , push button black 1o 1f , lip seal , hose for recharge of fresh water for extinguisher , 9lwater fire extinguisher assembly , co2 high rate discharge valve , electric/manual actuator , elastic guard ring , seal 100 x 146 x 2 130 x 7 x 8 , gasket made for rubber , fluid hose an 026 nd25 ruch od26 67 and free end l 2m , interface seal kit 9 5x1 5x1 78 fkm 80sh , mc30 oil hose peh16 nd25 nd 20 guill +1 1/2 union bsp l 2 m , fitted screw , plunger pipe 30/43 , heating element 540w (plate 385mm) , heating element 960w (plate 385mm) , fan blade , v ring seal v75a , o ring 28 24x2 62 20a8 , o ring 290x3 , pin , needle roller thrust bearing , washer dic m8 , slydring guide ring diam 55x50x2 5 turcite t10 , slydring guide ring diam 60x65x2 5 turcite t10 , spring pin e4 16 steel , copper gasket , locking plate stainless steel 1 4541 , anti extrusion ring diam 59x65 th1 3 ptfe ms28774 , gasketdia 8 2 x dia 11 4 th 1 , glydring seal diam 65 turcite t10 + o ring 227 8307 , check valve , copper seal 27 3x32x1 5 , copper seal 14x18 5x1 5 , o ring 34 6x2 4x39 4 , o ring 16x3x22 nbr 90 sh , o ring 30x3x36 , magnetic level switch , seal quad ring 21 82x3 53 , cover seal , piston seal , sealing washer , cover seal , seal 64 5x3 thick 1 70 sh , spring 12 5 0 8 47 7 5 , adjusting shim , seal set o ring+back up , ball bearing part 200 , washer 1554 1 , double pole miniature toggle switch , inclinometer , tias board , 2 postions rotary switch , central pusher unit , manometer inox bh nd100 type a 0 4 bar , absolute pressure switch , detector , overmouled electrode unit ref 100 , steel safety washer de14 , o ring 30 00x2 65 20a8 an , o ring 24 60 x 3 60 20a8 gn , annealed copper flat gasket 27 2 x32 x 1 5 , ruch sealing ring od26 67 , sealing ring for 316l ruch (nd10) , ruch sealing ring od33 40 , mechanical seal sleeve x2crnimo 17 12 2 (4) , wear ring x2crnimo 17 12 2 (9) , epoxy glue , clear heat shrink , valve gasket , ap hoisting lowering control solenoid valve
Tender For corrigendum : supply of various fabrication items for bm d d - st010260011-journal head liner support , st010260008- journal head liner 1 , st010260009-journal head liner 2 , st010260010-journal head liner 3 , st010260048-guard for journal upper bearing housing , st010160010- tension roll assembly for gravimetric feeder , st010160051-take up screw for gravimetric feeder , st010160003-weigh span roller assy , st010160088- head pulley bushing - gravimetric feeder , st010160050-bolt for gravimetric feeder door , st010160101-coc guide block , st010160012-take up block for take up pulley for gravimetric feeder , st010160014-head pulley bearing end cover , st010160016-head pulley bearing cover of gravimetric feeder , st010140264-2.5 mm sheet for sealing for id fan impeller , st010160102-gate rack l.h of 36 inch raw coal gate , st010160103-gate rack r.h of 36 inch raw coal gate , st010140265-taper pin for pa and fd fan casing , st010470348-modified sector plate adjustment system for raph 31.5vimt , sc110440038-m16 x 1000 mm stud full threaded with two nut of class 8.8 gr , co110140169-high tensile studs size- m30 x 1000. grade- 8.8 class. , co110140167-m10 x 1000 mm stud full threaded with two nut of class 8.8 gr , co110140168-m12 x 1000 mm stud full threaded with two nut of class 8.8 gr , sc110440002-m24x200 stud bolt astm a193 gr. b7 and 2 nuts astm a194 gr. 2h , sc110440035-stud bolt m24x90 of grade astm a193 gr b7 and 2 nuts astm a194 gr. 2 h , co110150140-plate washer m12. id-13mm. od-30mm. thickness-2mm , co110150141-plate washer m16. id- 17mm. od-40mm. thickness-2.5mm , sc310270055-mild steel scaffolding gratings as per drawing , st010430399- peep hole door , st010390317-bah lhs chute-stainless steel , st010390318-bah middle chute-stainless steel , st010390319-bah rhs chute-stainless steel , co030190063-straight ss protection shield , co030190062-clamp for protection shield , co030190064-expansion sleeve for protection shield //bid details 2 / 35
Tender For corrigendum : supply of hvac sensor and fittings for ventilation system e e - electromagnetic coil be 220v hz 50 ip67 with latch , latched magnetic coil be 380v 50hz ip67 , solenoid valve g3 by 4 ev220v epdm seal , solenoid valve g11by4 ev220v epdm seal , solenoid valve g2 ev220v epdm seal , filter g13by4 type y222 , filter g11by4 type y222 , filter g2 type y222 , thermostat kps 76 , thermostat kps 77 , sleeve l160 for thermostat kps , set of seals for thermostat kps , aluminum thermo-conductive compound for thermostat kps tube , assembly tape for thermostat kps l 392 mm , on board spares as per h-ta no.h-ta-460000- 104 annexure a-1 itemwise unit rate to be provided , on board spares as per h-ta no.h-ta-460000-104 annexure a- 2 itemwise unit rate to be provided , on board spares as per h-ta no.h-ta-460000-104 annexure a-3 itemwise unit rate to be provided , on board spares as per h-ta no.h-ta- 460000-104 annexure a-4 itemwise unit rate to be provided
Tender For corrigendum : supply of spares for breveni make gear box model number: sl 8503/fs/188.1-s6 5c r1 for hbf drives -v - incoming material - base, shaft, sleeve, chamber, stay bolt, shaft seal and all wetted parts, rotor, motor, inprocess ins, materials for assembly, final inspecti, standard tests, hydro test, name plate details & visual appearance such like free from damage, dent..etc , pump and its components