Latest hoisting machine scrap Tenders | Government hoisting machine scrap Tenders

CTN :45291537

05 Jun, 2026 2.99 Lacs

Darjeeling - West Bengal

Tender For tender for supply of repair maintenance and servicing of eot crane 2 ton - servicing and maintenance of cranes 02 ton an all allied works with load test. , bridge & cross traverse rail alignment by clamps fitting/ adjustment , replace repaire dsl or ip supply cable on long travel , replace current collector for smooth operation , hoisting motor 5.2kw , 3ph , sc servecing only , cross traverse motor 0.55kw , 3ph , sc servecing only , long travel motor 2.2kw , 3ph , sc servecing only , bridge wheel assembly maintenance and replacement of defective part any of wheel , bearing , spacer , shaft , coupling , brake , gearbox , trolley crab wheel assembly maintenance and replacement of defective part any of wheel , bearing , spacer , shaft , coupling , brake , gearbox , hoock block maintainance and replacement of defective part any of pullies , rope lock , pulley bearing , thurster bearing , cover fastners , replacement of hoist wire rope dia 12 6 nos 36 fibre core , hoist assembly maintenance and replacement of defective part any of coupling , brake shoes , bearing , spacer , shaft , gear. , equiliser pulley maintenance and replacement of defective part any of pulley , shaft , bearing , maintainance for span of the crane within limit , it must not wear wheels on either sides of flanges , maintainance for diagonals of crane within the limit , it must not wear flanges of lt wheels or must not get jam of lt motion , rubber buffers replacement , limit switch for any of motion long travel cross traverse hoisting ) , relay maintenance or replacement with accessories , cross traverse cable replacement , cross traverse cable trollies maintenance or replacement

State Government

CTN :45007424

26 May, 2026 1.49 Crore

East Nimar - Madhya Pradesh

Tender For corrigendum : complete overhauling of electrical wire rope hoist along with supply of spares for electrical wire rope hoist installed at coal mill area at 2x600 mw, stage-i, sstpp, mppgcl, dongalia. - scope of service, complete supervision & installation of new spares/replacement of damaged/eroded spares of all 08 numbers of hoist (04 numbers capacity-20 ton & 4 numbers of capacity-15ton)., scope of supply, spares for 20 ton hoist, brake motor 15hpx1000rpm, 40% cdf, 150st/hr, s4 duty, foot mounted sq cage f/s 160 l, terminal box required right side for 15t or 20t hoist make : siemens, brake motor 1.5hpx1000rpm, 40% cdf, 150st/hr, s4 duty, flange mounted sq cage f/s 90 s for ct<, terminal box required top side make : siemens, gear box with coupling for trolley, mdl: ibc162/25.9/200-24 make: premium, gear box with coupling for trolley, mdl: ibc162/18.9/200-24 make: premium, rotary limit switch make: soc, two way lever type limit switch, make: soc, disc brake for 15hp motor, make: - emco, type 14.458, size: - 20, disc brake for 1.5hp motor, make: - emco, type 14.458, size: - 12, cable trolleys medium duty, wheel dia min 40 mm., wire rope 20 mm / 6x36 steel core/ galvanized, make- ushamartin, push buttons with 12 meter cable, rectifier size- eh720hhd, long travel dsl system, i- chain (5 mm)-, ii- cable 6 mm epr, iii- fasteners (1/4x2 ), lt motor shaft, lt motor pinion, spares list of 15-ton hoist, brake motor 15hpx1000rpm, 40% cdf, 150st/hr, s4,duty, foot mounted sq cage f/s 160 l, terminal box required right side for 15t or 20t hoist make : siemens, brake motor 1.5hpx1000rpm, 40% cdf, 150st/hr, s4 duty, flange mounted sq cage f/s 90 s for ct, terminal box required top side make : siemens, gear box with coupling for trolley, mdl: ibc162/25.9/200-24 make: premium, gear box with coupling for trolley, mdl: ibc162/18.9/200-24 make: premium, rotary limit switch make: soc, two way lever type limit switch, make: soc, disc brake for 15hp motor, make: - emco, type 14.458, size: - 18, disc brake for 1.5hp motor, make: - emco, type 14.458, size: - 12, cable trolleys medium duty, wheel dia min 40 mm., wire rope 15 mm / 6x36 steel core/ galvanized, make- ushamartin, pendent push buttons, rectifier size- eh720hhd, long travel dsl system, chain (5 mm)-, cable 6 mm epr, fasteners (1/4x2 ), lt motor shaft, lt motor pinion

State Government

CTN :45303639

06 Jun, 2026 NA

Ranchi - Jharkhand

Tender For e-quotation for seeking firm rates of plant and machinery and materials category items for preparation/amendment of schedule of rate for the year 2026. - m 1055 - pumps supplying submersible pump sets confirming to is 8034 and motor confirming to is 9283. pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/ noryl impeller. motor suitable for working on 415v+10%, 3ph, 50 hz, a.c. supply with cable guard, thrust carbon/ fiber bearing to withstand entire hydraulic thrust, water proof winding shall be provided. the pump set shall be suitable for direct coupling. pump shall have suitable outlet as per manufacturers design. anti thrust stream lined non return valve shall be provided with pump. 3 meter submersible copper conductor cable in single/ double run shall be provided with each pump., submersible pump set 100 mm dia (with polypropylene/ noryl impeller) up to 20 stages 1 h.p. , 1.5 hp, 2 hp, 2.5 hp, 3.0 hp, 4.0 hp, 5.0 hp, submersible pump 150 mm dia (with bronze/ss impeller) up to 8 stages, 1.5 hp, 2.0 hp, 3.0 hp, 4.0 hp, 5.0 hp, 6.0 hp, 7.5 hp, m 1056 - pressure guage providing fabricating, testing and commisioning pressure vessel fabricating in m.s plate on providing foundation including epoxy paint, pressure gauge (100 mm dia), pressure gauge (150 mm dia), vacuum / combination gauge, m 1057 - lifting equipment chain pulley block supplying triple spur gear type chain pulley block suitable for capacity as below with 3 m lift complete with load chain and hand chain suitable for above lift, tested to 50% over load as per is 3832 carrying isi mark., 1 tonne capacity, 2 tonne capacity, 3 tonne capacity, electric operated circular or rectangular travelling crane (single girder) supplying single girder electrically operated rectangular over head travelling crane with 6 m lift complete with wire rope hoist, class ii duty, all three motions electrically operated by suitable rating motor ip 54, control panel and down pendant control block., 5 tonne capacity, above 6 m up to 8 m span, above 8 m up to 10 m span, 7.5 tonne capacity, above 6 m upto 8 m span, above 8 m up to 10 m span, 10 tonne capacity, above 6 m up to 8 m span, above 8 m up to 10 m span, m 1058 - lightening arrester, ab switch, insulators, lightening arrestor supplying, erecting approved make thyrite type lightening arrestor suitable for h.t. supply with necessary ancillary material complete on provided cross arm and connected to overhead line., suitable for 11 kv supply, distribution class, suitable for 22 kv supply, distribution class, suitable for 33 kv supply, station class, disc insulator. supplying, erecting porcelain disc type insulators with hardware fittings suitable for h.t. overhead line complete erected with nuts and bolts on provided cross arm, suitable for 11kv line, suitable for 33kv line, pin insulator supplying, erecting porcelain pin type insulators with hardware fittings suitable for h.t. overhead line complete erected with nuts and bolts on provided cross arm, suitable for 11kv line, suitable for 33kv line, air break switch without earth switch supplying, erecting approved make h.t. outdoor type gang operated air break triple pole switch of required capacity with 3 post / pin type insulator per phase , mounted in horizontal or vertical position on provided cross arm with adequate length of g.i. pipe for operating handle erected on extended square shaft. the operating handle provided with lock and key at suitable height from ground with necessary clamps, suitable for 11kv line, rocking / tilting type, rotating type, suitable for 33kv line, rocking / tilting type, rotating type, air break switch with earth switch supplying, erecting approved make h.t. outdoor type gang operated air break triple pole switch with earth switch of required capacity with 3 post / pin type insulator per phase , mounted in horizontal or vertical position on provided cross arm with adequate length of g.i. pipe for op

Central Government/Public Sector

CTN :45287725

29 May, 2026 49.41 Lacs

Visakhapatnam - Andhra Pradesh

Tender For running maintenance of technological equipment in converter shop of sms-1.- repair of technological structures in converter shop, mixer discharge spout door rope changing, lance oxygen and water hoses replacement and hose shifting , lance guide minor structural repairs during operation, assistance in removal of lance from thimble socket, converter tilt drive lube oil topping up in lube tank, minor structural repairs of ferro alloy chutes, hoppers and bulk material chutes during converter operation, shifting of stc, sptc&sdc, various running repairs of stc, sptc, sdc, and sample&service car, lime fines screw feeder jamming rectification by cleaning, shifting of mobile equipments like debricking m/c during breakdown in front of converter., tap hole drilling m/c drill bit hard facing, telescopic hoist rope changing/portable repair during relining of converter, well mix pipe changing in l.p bay, steel teeming ladle bell crank lever bracket/ trunnion collar changing, steel teeming ladle bottom purging adapter plate fixing, hot metal tilter /steel teeming ladle resting bracket repair, various minor structural and other repairs like dart pipe centering, tip cleaning and device locking etc in slag cut off device.replacement of charging crane/ mixer crane tilter hook, assistance in shifting jack car and telescopic hoist, minor repairs of lance carriage balancer during operation of converter, minor repairs of lance foldable platform &lance stands, minor repairs of dog house & dog house doors during operation, hot metal ladle spout repair, lub pump changing in revamped converters, shifting, jam cutting and other minor repairs of lance assemblies.

State Government

CTN :44271122

03 Jun, 2026 NA

Gandhinagar - Gujarat

Tender For corrigendum : supply, erection, testing & commissioning of wire rope hoist with replacement of existing one for pa fan & air pre-heater area for bmd at gtps.

Central Government And Public Sector

CTN :45280929

01 Jun, 2026 NA

Dibrugarh - Assam

Tender For supply of allen key 8 mm , allen key 10 mm , allen key 22 mm , slugging wrench , slugging spanner , reversible ratchet handle half inch , reversible ratchet handle three fourth inch , torque wrench , outside micrometer , soft face hammer 40 mm with steel handle , center punch , straight air drill machine , air grinder , measuring tape , tungsten rotary cutter 6x5mm , tungsten rotary cutter 6x13mm , tungsten rotary cutter 6x10mm , flat file , half round file single cut grades of cut second , half round file single cut grades of cut bastard , half round file double cut grades of cut second , half round file double cut grades of cut bastard , needle file , cutting wheel , grinding wheel or dc wheel , gas cutting torch , welding rod ms 7018 36 h , welding rod ss 308 , welding rod ss 309 , emery paper grade 120 , emery tape fine grade , cleaner , developer , penetrant , rustolene rust disintegrator , wire brush , tefflon tape , tig electrode , air hose pipe wire embadded , masking tape 50 mm , ss wire 1.6mm , ss wire 2.4mm , masking tape 75 mm , half inch impact hexagon bit socket 6 mm drive , half inch impact hexagon bit socket 8 mm drive , half inch impact hexagon bit socket 14 mm drive , half inch impact hexagon bit socket 17 mm drive , size 19mm three fourth inch drive socket 12 point , jack up bolt m10 x 150mm , jack up bolt m12 x 150mm , jack up bolt m16 x 150mm , buff flap wheel , 11mm deep socket 6 point , combination plier , circlip plier set , hydraulic hand pump , hydraulic jack button type , hydraulic jack with hand pump , air micro grinder 120 degree angle grinders 3 collet , air micro grinder 90 degree angle grinders 3 collet , curbide rotary burrs 5x10 mm , curbide rotary burrs 3x15 mm , oil stone size 150mmx50mmx25mm fine grade , klinger gasket 1.5mm, non metallic , tinsnips , cylindrical grinding stone 10x20 mm , taper grinding stone 10x20 mm , taper grinding stone 21x50 mm , cylindrical grinding stone 20x50 mm , chain hoist , triple boiled linseed oil sealing compound , premium polyester rope , dowsil rtv sealant 736 , pneumatic connector with coupling allen key 8 mm,size: lenghth of the long arm=100 mm, lenghth of the short arm=36 mm, moc: chrome vanedium steel, black finsh, allen key 10 mm,size: lenghth of the long arm=112 mm, lenghth of the short arm=40 mm, moc: chrome vanedium steel, black finsh, allen key 22 mm,size: lenghth of the long arm=200 mm, lenghth of the short arm=80 mm, moc: chrome vanedium steel, black finsh, slugging wrench, size: 1 inch,moc: chrome vanedium steel, heavy duty black industrial finish- rust resistant, slugging spanner, size: 3/4 inch,moc: chrome vanedium steel, heavy duty black industrial finish- rust resistant, reversible ratchet handle 1/2'',head dia: 64 mm, head depth: 29 mm, gear action: 32 mm, oal: 605 mm, reversible ratchet handle 3/4'', head dia: 64 mm, head depth: 29 mm, gear action: 32 mm, oal: 605 mm, torque wrench, 1/2 inch square drive, 7-35 kg, widtht: 50 mm, height: 29 mm, length: 805 mm (approx. ), weght: 3.9 kg (approx. )., torque wrench, size :1/2 inch square drive, 25- 135 nm, torque wrench, size :1/2 inch square drive, 50-220 nm, torque wrench, size :3/4 inch square drive, 135-675 nm, outside micrometer, range (200-225)mm, graduation: 0.01mm, material of the frame: stainless steel, material of the spindle and anvil: hardened stainless steel, soft face hammer 40 mm with steel handle, center punch, length: //bid details 2 / 59

State Government

CTN :45276192

04 Jun, 2026 3.99 Lacs

Vidisha - Madhya Pradesh

Tender For pre-monsoon repair and maintenance of 7 no. vertical gate rope drum hoist type at rehti medium project distt. vidisha

CTN :45258391

30 May, 2026 NA

Banda - Uttar Pradesh

Tender For erection of lifting assembly (rope drum hoist type), central drive unit of cross regulator at km 29.820 of ken main canal, banda

CTN :45258404

30 May, 2026 NA

Banda - Uttar Pradesh

Tender For erection of superstructure and lifting assembly (rope drum hoist type), central drive unit of escape regulator at km 29.800 of ken main canal, banda