Tender For corrigendum : supply of aero engine components from hal supplied raw material and technology e e - quill shaft , spline bush , right thrust bearing , impeller , impeller , impeller , impeller , impeller , blade wheel , impeller , impeller , drive , quill shaft , sector
Tender For corrigendum : supply of pure iron flat for magnet holder of qbat relay of size 37.80/37.85mm width, 3.00/3.07mm thick and 59.00/59.50mm long. raw material: 1. soft-iron gr.1 of m/s.midhani/hyb 2. ame-8 of m/s.edelstahwerke-buderus/germany. material properties: 1. cold rolled in annealed condition. 2. high purity iron with low residual elements. 3. impurity max c=0.007%, mn=0.3%, si=0.02%, s=0.014%, p=0.006%. [ warranty period: 30 months after the date of delivery ]
Tender For supply of bogie frame to drg. no. (a) icf/mrvc/d-0-3-001, alt "n", col-ii (or) (b) icf/mrvc/d/bt-0-3-001, alt "c", col -ii along with damper fixing bracket to drg. no. (339)ac/dcemu/d6-0-1-602,col.i - 4 nos andbolt complete to drg. no. emu/m/3ph-0-2-002, alt "c", col.i - 16 sets bogie frame to be supplied without nylon bushes where ever applicable and shall confirm to rdso/specn.c-9202, rev-2 or latest. the firm shall fulfil the requiremnt as per icf/md/specn/147, issue status 01, rev-02 with amendment no- 02. special condition : - suppliers commitment will be there to supply as per drawing -(a) ( for dash pot arrangement ) or as per new drawing - (b) ( for adoption of conical spring ). - one month notice willbe given to vendor whether he has to supply as per drawing - (a) or drawing - (b). -rate quoted will be applicable to both drawing - (a) and drawing - (b) . i) paint scheme shall be as per drawing. ii) qap to format icf/ims/md/f-31 shall be prepared along with relevant documents and kept ready for developmental/educational order. iii)firm should supply bogie frame along with the dimensional report, stress relieving report and radiography films. iv) firm should have induction/electric furnace for stress relieving of bogie frame. v) prototype inspection is applicable only for first time of developmental/educational order. vi) stage inspection to be done as below. (a) raw material stage 1. ensure the raw material used using portable spectrometer machining stage 1. dimensional checks 2. edge preparations (b)welding stage 1. weld parameter to be checked and recorded. (c) surface preparation and painting stage. 1. short/sand blast to the requirements. 2. painting process as per the specification. 3. final product inspection. [ warrantyperiod: 30 months after the date of delivery ]
Tender For corrigendum : procurement of raw material, machining, testing, heat treatment, inspection, packing & supply of "ram drive end body subassembly, material: aluminum bronze as per drg. no. kapp-3&4-35221-2056-dd with helicoil sli-si-c6-cn-12-6 no., dowel pin as per drg. no. kapp-3&4-35221-2082-dd - 2 no., gear bearing as per drg. no. kapp-3&4- 35221-2062-dd - 1 no., gear bearing as per drg. no. kapp-3&4-35221-2064-dd - 1 no., cover plate as per drg. no. kapp-3&4-35221-2081-dd - 1 no., hex. socket head cap screws size m6 x 1 - 6g x 20 mm lg, material: ss - 6 no.". refer detailed technical specification in annexure-3