Latest impeller shaft Tenders | Government impeller shaft Tenders

State Government

CTN :43467490

13 Jan, 2026 NA

Delhi - Delhi

Tender For s/i/t/c of e/m equipments and allied works for newly re-bored tube well at okhla vihar near majar in okhla constituency ac-54. - supply of submersible pump set fitted with dynamically balanced ss impeller mounted on stainless steel shaft with protection sleeve having stage bowl & closed grained shorted type impeller, the pump will be directly coupled to required wet type induction motor of 7.5 hp, 15 stage, speed 2900 rpm suitable for operation of 3 phase, 415 volt, 50 hz, ac supply with efficiency 70% at following duty point: 200-125-75 lpm on 89-124-133 mtr. head.having discharge outlet 50 mm and outside dia 142 mm.make: bs/skope/ any djb approved. , supply of hut type electrical feeder pillar / fabricated with 50 x 50 x 6mm angle iron and 16 swg ms sheet with horizontal and vertical intermediate member of suitable size. i.e. 1370 mm x 760mm x 460 mm. with arrangement for mounting of switchgear and electrical energy meter i.c. painting heaving following item fitted. a) mccb 63 amp, 4pole, 415volt, 35 ka -1 no. b) rccb 63 amp, 4pole with earth fault indication protecting a circuit automatically in the event of earth leakage sensitivity 100ma, - 1 no c) fully automatic star delta starter of relay range 13-21 amp. (7.5 hp to 10 hp) 3 phase oil immersed type -1 no.d) ampere 96 x 96 mm. square shape 0-30 amp-1 no. e) voltmeter 96 x 96 mm. square shape 0-500 volt-1 no.e) indicating lamp (a set of 3 lamps) 1.setf) shunt capacitor of 10 kvar mpp type with three phase isolator with suitable banking g) motor protection assembly with earth leakage protection phase sequence corrector, single phasing, protection, overload protection, high voltage / low voltage protection time delay power on, programmable time switch i.c. r&b phase facility to change over from automatic, to manual &vice verse for up to 10 h.p -01 nos.complete wiring &installation of above accessories with required copper conductor wire and thimble etc. 01 job.make of all components: any djb approved., s/o pvc insulated and pvc sheathed cable with plain copper conductor having 3 phases, 3 core flat for submersible motor of 4 square mm size each 100 mtrs. make:grandlay / havells./any djb approved make, s/o m.s. clamp of 600 mm length duly fabricated out of 12.5 mm thick 75 mm wide, m.s. plate for holding the pipe of 50 mm dia., s/o double flange gi column pipe 50 mm dia medium class each of 3 mtrs long duly threaded on both ends, welded fitted with gi flange on both ends with slot of submersible cable. make: tata/ jindal./any djb approved make, s/o/ tail piece of the medium class gi pipe 500 mm long with one end threaded as per outlet of pump & another end flanged as per size of gi pipe 50 mm dia., s/o gi 90 bend of size 50 mm dia having both side flange (heavy duty)., supply of ms nut bolts off size as per requirement., s/o rubber packing for 50 mm dia flange., fabrication and supply supply of bore cover approx size 1x1 made out from 6mm thick m.s. sheet in 2 halves and a circular hole in centre 3-1/2 dia. with locking arrangement by nuts and bolt. , earthing with g.i. earth pipe 4.5 meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required., providing and fixing 6 swg dia g.i. wire on surface or in recess for loop earthing as required., installation of t/well by lowering of sub p/set with all allied above items. this includes installation and grouting of panel boards with all electrical wiring & cabling at site. all tools & tackles i/c. tripod chain pulley blocks etc. shall be arranged by the firm. this includes testing & commissioning of t/well on load at site i/c. cartage, loading & unloading of material. it also includes a trial run of 30 hrs operation successfully by the firm. all required civil work included in the scope of work.

Central Government / Public Sector

CTN :43483719

20 Jan, 2026 NA

Kamrup - Assam

Tender For procurement of spares for pumps 027-p-05a/b & 32-p-15a /b/c - impeller cs p/n 230, ring, impeller, suction side, g b bushing ci p/n 325, impeller shaft sleeve ansi 410 p/n 520, intermediate sleeve ansi 410 p/n 521, sleeve, shaft, impeller, coupling, love joy, shaft, hsg,brg,pmp,p/n-330 kvses 50 x 250, ib housing ci p/n 334, bearing lock nut ms p/n 924, casing pn 102, casing wear, impeller w/ wear ring, finger pn 506, shaft with keys, gaskets & o-rings

CTN :41669226

10 Jan, 2026 NA

Uttara Kannada - Karnataka

Tender For bid to ras corrigendum : tender for supply of procurement of various spares for spb kar : : - alternator , adc controller , vibromount , battery charger mass 24-100 a sbc 2450 , td 400 water jet main body , core-as-aftc , turbo cartridge gp , fm200 cylinder , impeller shaft mechanical seal , impeller , battery charger mass 24-304 3 output sbc nrg

Central Government/Public Sector

CTN :43272599

15 Jan, 2026 11.56 Lacs

Ganjam - Odisha

Tender For corrigendum : supply of supply of spares for vertical submersible pump make kbl : : - intermediae shaft , head shaft , impeller shaft , strainer , split lantern ring , split gland , bearing spider , thrust brg. carrier , bearing holder , shaft sleeve d. s. , shaft sleeve , impeller nut with helicoil insert , casing ring , impeller ring , set of oil seal , set of gaskets , set of keys , pipe nut , screwed coupling , shaft sleeve-ps

CTN :42812852

09 Jan, 2026 9.99 Lacs

Gautam Budnagar - Uttar Pradesh

Tender For bid to ras supply of veh spare parts d d - acey , steering lower coloumn assy , filter assy for power steering reservoir , assy delivery line fuel filter to fip , assy return line fip to t connector , assy delivery line firwl to prmg pump , hose coolant radiator to thermostat , rubber hoseuc line to radiator , hose radiator to vent tube , fuse pal boltable 80a iso8820 , fuse pal 60a iso8820 , fuse pal 40a iso8820 , fuse ato blade 5a iso8820 , fuse ato blade 10a iso8822 , fuse ato blade 15a iso8821 , fuse ato blade 20a iso8822 , fuse ato blade 25a iso8820 , fuse ato blade 30a iso8821 , power relay bs1 2 3 4 6 , relay 40a c o contact , mini relay ems relay bs3 4 6 , wiper blade set of 2pcs , assy fuel injector bs3 4 , roller ac belt tensioner , assy rear shock absorber bs1 3 4 , timing belt idler big , timing belt idler small , cam sensor , crank sensor , rear cover crank case , hoseegr cooler to coolant return pipe , hose egr cooler to ucl pipe , hoseoil cooler to coolant return pipe , rubber hose-crankcase to oil cooler , assy simaf sensor mount for air cleaner , assy vacuum pump bs3 4 6 , assy turbocharger bs3 4 , hand brake shoe rear , fly wheel assy , clutch plate , pressure plate , release bearing , fly wheel breaing , clutch system flexible pipe , clutch master cylinder , brake master cylinder with vaccum booster , front brake disc pad , rear brake disc , fuel filter assy , head light tube hellogen type 100 wat , oil filter assy , ac filter assy , air filter assy , belt main , shock absorber assy front rear , wipper blade set front , wipper blade rear , radiator fan assy , radiator assy , horn assy 12 volts low high tone , def delivery pump assy , water pump assy with packing scorpio s 3 , head light assy bullet royal enfeld , disc pad front scorpio s4 , disc pad front scorpio s3 , disc pad front scorpio s11 , mpv dampher , air filter , water pump assy , alternator belt , ac belt , disc pad brake , head light assy , air filter assy safari , wiper blade ertiga , head light assy lh rh ertiga , fuel filter ertiga , realese bearing m gypsy , spark plug m gypsy , fuel filter m gypsy , horn m gypsy 12 volts , ac filter , disc pad brake front , wipper blade set , fan belt , water pump , tail light assy rh lh , head light assy lh rh , spark plug , ignition coil , strut assy front rh suspension , strut assy front lh suspension , front arm assy rh lh , stabilizer rod set rh lh , self starter motor assy , side view mirror lh rh assy , disc brake rotor front , disc calliper assy , belt tensoner , radiator fan , hose pipe out let in let , front shock absorber , front suspension kit complete , rear tail lamp assy dow wali , bulb double filament 12 volts , wipper blade , fog lamp assy with bulb 12 volts , head lamp bulb 12 volts 1141 , brake and parking bulb 1176 12 volts , horn 12 volts , oil filter no f7a01500 , diesel filter fnj0100 , diesel filter fhn00400 , wiper blade , relay 12 volts 30amp 4 pin , head light relay 12 v 30 amp 4 pin 6 plus 6 , load dump relay 12 v 30 amp 4 pin 4plus4 , brake disc pad , rear brake shoe , front whell bearing , suspension bush kit , joint front stablisar bar clutch plate , pilot bearing , clutch release bearing , door lock inner rh lh , wheel cover rh lh , front half axle shaft lh rh , shock absorber front , air filter //bid details2 / 134housing assy , oil filter , fuel filter , joint tie rod ball joint lh rh , sensor set all complete , combination switch assy , horn 24 volts

CTN :43465273

27 Jan, 2026 NA

Mumbai - Maharashtra

Tender For tender for supply of radial-lip shft seal , oil seal , grease nipple 1 8 bsp , ball bearing deep groove , felt seal , timer 60 sec , 73a contractor , control terminals , ball bearing deep groove , led indicating light , color red , led indicating light , color yellow , led indicating light , color green , aux. contactor 2 no + 2 nc , cable sleeve , tapper pin , tapper pin , float switch , temperature sensor with oisplay unit , joystick , element for return line filter , counter balance valve , control terminals , bearing , main shaft , grease nipple (1 4 bsp) , slipping clutch cum flexible coupling , 63a tp switch , bi-metalic overload relay , pneumatic time on-delay , bridge rectifier complete , felt seal , push button with black actuator , over load relay 17.4-24a for slow speed , 6a contractor 220v ac coil (5 no+3 no) , push button (green) 1no , pump f water sanitary centrifugal horizon 10 40 with motor , pump centrifugal vertical 63 80 with motor 380v fire pump , puse button with element , grease nipple 1 8 bsp , bearing 7313b , bearing 6006 , bearing 6007 , bearing 1207 , oil seal 35x55x8 double (mi) , indicating lamp red complete , indicating lamp yellow complete , indicating lamp blue complete , auxiliary contacts for 16a contactor , coil for 16a contactor , thermister protection relay , bridge rectifier surge suppressor , push button (yellow) complete , indicating lamp(clear) complete , push button (green) complete , indicating lamp (red) complete , indicating lamp (green) complete , bearing , bearing , bearing , circlip , over load relay , over load relay with ssp independent , thermister relay 1no+1nc 1e & 2a , pilot lamp yellow lens 230v bulb , pilot lamp amber lens 24v bulb , over load relay 17.4-24a , timer on-delay , control terminal 2.5mm , motor protection relay

CTN :43402074

06 Jan, 2026 NA

Multi City - Chhattisgarh

Tender For corrigendum : engineering items ( non authorized dealer)-- , aira valve auto mation ce 1128 valve automation f/b- r/b full bore end type- s/e, size dn 25mm bore seat/stem htfe 98316 bore- 25mm flanged end both side., high flow pump size- 5 inch head- 40 mtr. with motor pump or base freme, s.s. ball valve flange type size- 25mm make- aira, rubber stator for high flow pump size- 4” x 4” model no. rbh4152aabn make- risanshi, rotary screen taflon roller assembly front assembly make- uttam, juice rotary screen, rotary screen taflon roller assembly rear assembly make- uttam, juice rotary screen, rotary screen taflon roller assembly front surface assembly make- uttam, juice rotary screen, ‘b’ mescuite pump spare roter with shaft and gen metel strips pump size- 8 x 8 inch make gita pump, valency welding rod bronzocar- 32 ac/dc size- 3.15mm, valency welding rod bronzocar- 32 ac/dc size- 4.00mm, sapre tyre for following size- f- 60, sapre tyre for following size- f- 70, sapre tyre for following size- f- 80, c.i. pin bush coupling complete assembly with pin bolt with rubber bush size- 10”, c.i. pin bush coupling complete assembly with pin bolt with rubber bush size- 12”, rubber bush for pin bush coupling rubber bush size- id 19 x od 38mm x length- 40mm, en- 8 round bar size- 25mm x 4 mtr., en- 8 round bar size- 30mm x 4 mtr., en- 8 round bar size- 36mm x 4 mtr., en- 8 round bar size- 40mm x 4 mtr., coupling bolt med. en- 8 size bush bolt dia- 19mm bush length bolt- 45mm bolt caller 5mm thick- 2500, thread length- 21mm, 5/8” bsw thread with out thread- 20mm length dia- 5/8 inch, "uc-1500 type uttam make machine continuous machine spare pully housing complete assembly", "uc-1500 type uttam make machine continuous machine spare main housing assembly complete set", "uc-1500 type uttam make machine continuous machine sparebuffer chamber assembly", top scraper for mill no. 3, 4 pitch 35mm material- c.i. 1030 gr. (as per drawing) , "discharge scraper for mill no. 3, 4 pitch 35mm material- c.i. 1030 gr. (as per drawing)", b messacute pump complete 6" x 6" for b messacute without motor make risanshi, top gear transmission make model no. 2340 hbx ratio- 36, s.no. 18026797, top gear transmission make model no. 22300 hbx ratio- 37.85, s.no. 16123824, level tranmitter range - (-2150 to 0 mmh2o) supply - 10.5 to 45vdc, output - 4 to 20ma with installation & trail support warranty - 2 year make - abb/siemens/yokogawa, controller for spray enggineering panel make - winpac model no - wp - 8147 pwr - (10 to 30 vdc) with installation & trail warranty - 02 year, solenoid valve coil with hand regulator make - rotex model - mf42 - 3012x3 - 62g (3/2 way) supply - 230vac, esp level switch probe with controller and cables material - stainless steel no of parts - 4 ports, meadia type - dry material working pressure - 150°c make - eip enviro level control pvt. limited with installation & trail warranty 02 year, mix bad (mb) conductivity sensor cable with its controller work on low cell constant make- ion exchange model - indian con 5000w with installation support warranty 02 year, ph sensor cable with controller make - ion exchange model no - indion 4000 phw with installation & trail supports warranty - 02 year, touch hmi programmed display make - formaplastic model - weintexmt 5017 input power supply 24 vdc warranty - 02 year, power supply transformer make - kasunga model - dvsc 200 aem4it ( ac415/110 . 100v 200va), load cell make - minibea model - cbe1 - 50k warranty 02 year, programmed plc for batch type machine make - mitsubishi electric r5485 & lan card suported model no - fx5u-64m, programmed by formaplastic warranty - 02 year installation service support & trail work, 24 volt dc coil for solenoid valve ip - 65 make - techno as per sample provided, coil for solenoid valve supply - i-230vacol make - rotex as per sample, temprerature controller make - electronic system & devices model - esd9223 warranty - 02 year, plastic chair - ni

Central Government/Public Sector

CTN :43421016

12 Jan, 2026 NA

Sundergarh - Odisha

Tender For supply of mechanical spares for water system sms ii c c -20413501000840 g follower f rhob h wel pn 1 pd r 279052 , item 280 20413501000835 bracket f rhob h well f1 pmp pd r 279052 , item 290 20413501000838 spacer f rhob h well f1 pmp pd r 279052 , item 300 20413501000842 sleeve de f dc 1 k1 pmp pn 2 pdr 279053 , item 310 20413501000841 sleeve nde f dc 1 k1 pmp pn 1 pdr 279053 , item 320 20413501000843 sleeve f slurry w2 pmp pn 3 pd r 279053 , item 330 20413501000845 sleeve f dc 2 f1 pmp pn 5 pd r 279053 , item 340 20413501000844 step coupler pn 4 pd r 279053 , item 350 20413501000853 parall couplr f c wel f1 pmp pd r 279053 , item 360 20413501000846 spacer f cwc f1 pmp pn 6 pd r 279053 , item 370 20413501000826 g folwr f cwc h well m1 pmp pd r 284643 , item 380 20413501000827 g flwr f cwc dc 5 k1 pmp pn 2 pdr 284643 , item 390 20413501000828 g folwer f ffp f1 pmp pn 3 pd r 284643 , item 400 20413501000847 g followr f dc 4 k1 pmp pn 4 pd r 284643 , item 410 20413501000829 g followr f clcp f1 pump pn 5 pdr 284643 , item 420 20413501000830 g followr f booster pmp pn 6 pd r 284643 , item 430 20413501000831 g fwr f scalepit k2 pmp pn 7 pd r 284643 , item 440 20413501000832 g followr f eoht f2 pmp pn 8 pd r 284643 , item 450 20413501000833 g followr f dc 1 f2 pmp pn 9 pd r 284643 , item 460 20413501000848 g follower pn 10 dwn pd r 284643 , item 470 20413501000849 g follower pn 11 pd r 284643 , item 480 20413501000902 head shaft dwn pd r 288347 , item 490 20413501000904 intermediate shaft dwn pd r 288347 , item 500 20413501000903 impeller shaft dwn pd r 288347 , item 510 20413501000907 coupler dwn pd r 288347 , item 520 20413501000906 sleeve dwn pd r 288347 , item 530 60210009010841 sleeve shaft dwn pd r144636 pos 311 , item 540 20413501000908 impeller nut dwn pd r 228471 , item 550 20413501000905 spyder dwn pd r 288347 //bid details2 / 56

Central Government/Public Sector

CTN :43399860

12 Jan, 2026 NA

Dakshina Kannada - Karnataka

Tender For supply of bearing distance sleeve , impeller shaft with keys , brass logging ring - set of 2 , lock nut , impeller , rubber water thrower , locking washer

corporations/Associations/Others

CTN :43407122

16 Jan, 2026 NA

Kolkata - West Bengal

Tender For mfg. supply and fitting fixing impeller shaft pump unit no. 1 and mfg. supply of en-24 coupling unit along with coupling spring for horizontal pump unit no. batliboi-1 at bdps.

Impeller Shaft Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

State Government

Central Government / Public Sector

Central Government/Public Sector

Central Government/Public Sector

Central Government/Public Sector

corporations/Associations/Others