Latest lathe digital readout system Tenders | Government lathe digital readout system Tenders

CTN :42091353

14 Oct, 2025 NA

Tiruchirappalli - Tamil Nadu

Tender For supply of solid carbide micrograin end mill centre cutting dia 16 x 4 flutes cel 32 x oal 92 helix angle 30 de

CTN :42058298

06 Oct, 2025 NA

Bangalore - Karnataka

Tender For supply of stg cutting tools e e - thread cutting die set 3 8 inc bspt taper thread , thread cutting ring gauge go no go 3 8 inc bspt taper thread , thread cutting chaser m10 x 1.5mm , drill twist hss ps 4.9 mm , end mill cutter hss ps 8.5 mm dia , end mill cutter hss ps 9 mm dia , thread cutting die m35 x 1.5 mm , thread checking ring guage go and no go m35 x 1.5 6h , thread cutting chaser m12 x 1.5mm

CTN :42005117

15 Oct, 2025 NA

Tiruchirappalli - Tamil Nadu

Tender For supply of solid carbide sub micro grain, center cutting end mill dia 20.0 x cel 38 x oal 104 x shank length -5

Central Government/Public Sector

CTN :41902235

09 Oct, 2025 6.92 Lacs

East Singhbhum - Jharkhand

Tender For construction of room at crd building inside turamdih mill : : - earth work in excavation by mechanical means hydraulic excavatorormanual means over areas exceeding 30 cm in depth 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m as directed by eic.all kinds of soil , filling available excavated earth excluding rock in trenches plinth sides of foundations etc. in layers not exceeding 20 cm in depth consolidating each deposited layer by ramming and watering lead up to 50 m and lift upto 1.5 m , supplying and filling in plinth with sand under floors including watering ramming consolidating and dressing complete. , providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering . all work up to plinth level 1 cement 3 coarse sand 6 graded stone aggregate 20 mm nominal size , providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering shuttering finishing and reinforcement. all work up to plinth level 1 cement 1.5 coarse sand 3 graded stone aggregate 20 mm nominal size , reinforced cement concrete work in walls any thickness including attached pilasters buttresses plinth and string courses fillets columns pillars piers abutments posts and struts etc. above plinth level up to floor five level excluding cost of centering shuttering finishing and reinforcement 1 cement 1.5 coarse sand 3 graded stone aggregate 20 mm nominal size , reinforced cement concrete work in beams suspended floors roofs having slope up to 15 deegree landings balconies shelves chajjas lintels bands plain window sills staircases and spiral stair cases above plinth level up to floor five level excluding the cost of centering shuttering finishing and reinforcement with 1 isto 1.5 isto 3 1 cement 1.5 coarse sand zone 3 graded stone aggregate 20 mm nominal size. , brick work with common burnt clay f.p.s. non modular bricks of class designation 7.5 in foundation and plinth in cement mortar 1 isto 6 1 cement 6 coarse sand , brick work with common burnt clay f.p.s. non modular bricks of class designation 7.5 in superstructure above plinth level up to floor v level in all shapes and sizes in cement mortar 1 isto 6 1 cement 6 coarse sand , centering and shuttering including strutting propping etc. and removal of form for foundations footings bases of columns etc. for mass concrete , centering and shuttering including strutting propping etc. and removal of form for suspended floors roofs landings balconies and access platform , centering and shuttering including strutting propping etc. and removal of form for lintels beams plinth beams girders bressumers and cantilevers , centering and shuttering including strutting propping etc. and removal of form for columns pillars piers abutments posts and struts , demolishing brick work manuallyor by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of eice. in cement mortar , cement concrete flooring 1 isto 2 isto 4 1 cement 2 coarse sand 4 graded stone aggregate finished with a floating coat of neat cement including cement slurry but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate cement make as per direction of eic , steel reinforcement for r.c.c. work including straightening cutting bending placing in position and binding all complete upto plinth level thermo mechanically treated bars of grade fe500d or more make as per direction of eic , 15 mm cement plaster on the rough side of single or half brick wall of mix 1 isto 6 1 cement 6 fine sand rates for external plastic are for height upto 10m from ground level in less otherwise stated cement make as per direction of eic , 12 mm cement plaster of mix 1 isto 6 1 cement 6 fine sand rates for external plastic are for height upto 10m from ground level in less otherw

CTN :41829127

03 Oct, 2025 NA

Calcutta - West Bengal

Tender For supply of solid carbide endmill cutter spirial 30 deg, 4 fluted sqr end r. h. without centre cutting, micro grai , solid carbide end mill cutter straight shank 4 fluted 30 degree spiral cutting dia 12 mm, flute lengt

Central Government/Public Sector

CTN :41797209

03 Oct, 2025 NA

Bangalore - Karnataka

Tender For tender for supply of sandvik tools d d - insert - drilling , kpht 150405 fr-cm , tcgx06t104-al h10 , tcex050100l-f 1024 , tcgx110302 al h10 , tcmt110304pm 4315 , r/l331 1a-054515h-wl 1030 , insert - boring , insert - boring , insert milling for steel , insert turning for aluminium , insert for titanium , insert for drilling-for titanium , insertperipheral- indexable drill , insert milling cutter-for ti , insert milling cutter for titanium , insertmilling for titanium , insert - milling for steel , insert for titanium , insert n151.3-300-25-7p gc 2135 , insert - milling , insert - milling , insert - boring , insert - boring , insert - drilling for titanium , insert - boring , insert - milling-for al ti and stee , insert - drilling , insert - boring , insert - milling , insert - milling , step drill 10.5 dia , insert - turning operation turning , n151.3-400-30-7g 1125 , n123h2-0500-ro 2135 , insertsknux 164010r11 235-steel hrc 45 , insertsknux160410r05 235-hrc45 , insertsvbmt 160408-um 1125- hrc 45 , insertsvbmt 160404-um 1125-steel hrc 45 , ccmt 09t304 wm - 1125- steel , ccmt 09t308 wm - 1125- steel , ccmt 060204um -1125 , snmg 120408 pm gc4225 , vbmt 160408 um - aluminum grade , vbmt 160404 um - aluminum grade , vbmt 110204- 1125 , dcmt 070204 um - 1125 , n123h1 - 0400 - 0002 - 1125 , n123f1 - 0250 - 0002 - 1125 , insertsn123e2 - 0200 - 0002 - 1125 , l123g2-0300-0502-cm-1125 , r166. 0l 11mm01 -150-1125 , r166. 0l 11mm01 -200-1125 , r166.0l 11mm01 -250-1125 , 266rl 16vw01a002m-1125 , 266rg- 16vm01c001m-1125 , 266rg - 16vm01a002m-1125 , 254r - 16cc01 - 185 , 254lg - 16cc01 - 185 , n123h55-25a2 , n123g55-25a2 , 3 mill 7 z2r2 special mill , 3 drill8-8 , 8 with chamfer , 3 drill6 8 , 8 with chamfer , 3 drill10 , 5 12 with chamfer , drill9 , 17 10 with chamfer , 3 drill13 , 25 14 with chamfer , 3 drill5 7h10 with chamfer , 3 drill6 , 1 with chamfer , 3 drill10 , 3 12 , 5 with chamfer , 3 drill16 , 8 11 , 23 12 chamfer , 3 drill6 , 1 with chamfer long , 3 tap m7x1 long hss , 3 mill7 , 8 pilot drill -hole4 , 3 drill4 special drill , 3 reamer8h7 special reamer , insertcentral - indexable drill , insertperipheral- indexable drill , insert - side and face milling cutter , insert - side and face milling cutter , insert screw , insert - side and face milling cutter , insert screw , insert - side and face milling cutter , insert - face mill cutter , insert - chamfering tool , insert - face mill cutter , insert - face mill cutter , insert - mill cutter , insert - back chamfering , insertcentral - indexable drill , insertperipheral- indexable drill , insert screw , 392.1014-100.40 120a , special cutting head - coroturn with tr-vb1308 insert , dmin dia 37mm , wf 19.5mm , left hand , coupling size 32 , lf 32mm , torque wrench sandvik make , corothread 266 shank tool for thread turning , left hand , dia 20mm , dmin 25mm , oal 250 mm , insert seating 266.ll-22 , insert screw , key - 20 ip , special corothread 266 insert , coromill mh20 face milling cutter dia 20mm cyl sh 20mm , no.of insert pockets 2 , oal 120mm , coromill mh20 face milling cutter dia 63mm arbor dia 22mm , no.of insert pockets 6 , oal 40mm , insert , coromill mh20 , insert for milling hardened steel , corocut qi , cutting head for groov , boring bar dia.25 sandvik make equlnt c4-570-2c-25064 , coroturn 107 , cutting head for turning , coupling sl 25 , dmin 35mm , insert seating vbmt/vcmt 1604 , functional lengthlf 22 mm , right hand , insert , insert , insert , insert , insert , tm860.4 nm-597404 for step drill step drill dia 9.1/10.1 - drawing furnished , mh20 080425m m20 1230 , r790 2205 16phpl 1230 , r300 16486pl s30t , 327 r12 2225 002 gm 1025 , r217 14c 045 100 ac 13 1630 , tm860.4 nm-596259 , tm435.t-xf-525943 , 435.t-0650-a1xf h10f , r217 130co 8215 0cc 21k 1630 , vbgt 160404 al h10 , vbgt 160402 al h10 , vnmg 160404 h13a , face milling cutter dia 80mm , face milling cutter dia 63mm , face milling cutter dia 100mm , insert for milling , 8 cutting edges , 266rg-16ac01f080e