Latest low voltage motor Tenders | Government low voltage motor Tenders

Central Government / Public Sector

CTN :40255382

29 May, 2025 NA

Secunderabad - Telangana

Tender For supply of 120w hot water booster pump suitable to work on 230v,50hz supply, with following paramete rs and specifications 1.discharge 30lpm. 2.operating head 9m. 3.input/output delivery size 19 mm. 4.integrated magn et/ epdm rubber/pp flow switch for starting and stopping the pump when tapping point is turned onoff. 5.three position selector switch(off,auto,manual). 6.induction motor with stator copper winding,ceramic radial bearing and carbon thru st bearing. 7 composite pp 30% gf material impeller 8. epdm rubber non return valve ball) 9 aluminium oxide shaft 10 cataphoresis-coated cast iron/ ss pump housing make: grundfos,ksb,texmo,crompton or equivalent [ warranty perio d: 12 months after the date of delivery ]

CTN :40218970

12 May, 2025 88

Yelahanka - Karnataka

Tender For pump motor repair - guide vane, oil seal steel bush(oil seal sleeve), oil seal(pump oil seal), intermediate piece (i.p.) with i.p. leaded bronze bush, pump bowls, rewinding of motor of 20 hp, rewinding of motor of 17.5 hp, rewinding of motor of 15 hp, rewinding of motor of 12.5 hp, rewinding of motor of 10 hp, rewinding of motor of 7.5 hp, rewinding of motor of 5 hp, rewinding of motor upto 3 hp, transportation of pumping machinaries, motor base with pin, circlips(small), bearing (gun metal bush) centrifugal cost aluminium bronze bearing bush, studs and nuts, tip carbon/ferrode padding, thrust bearing block assembly (tb bottom), carbon housing(tb plate), lock ring(circlip big), lower housing, upper housing, lower flange, upper flange, labour charges (overhauling of pump only), brass filter, strainer, cable guard, pump coupling (stainless), pump key (stainless steel) upto 8 stages, pump shaft (stainless steel) counter less ground with key way upto 8 stages, allen screw, steel bush (i.d.o. ss sleeve), d.o. bearing( i.d.o lb bush), discharge outlet (d.o.) bearing(lb bush) and d.o steel bush(ss sleeve), impeller shell moulded with aluminium & bronze, supply and fixing of voltmeter, supply and fixing of ammeter, supply and fixing of led indicator, supply and fixing of wiring kit(sd upto 25hp), supply and fixing of wiring kit(dol upto 7.5hp)(mr), supply and fixing of no-volt (nv) coil, supply and fixing of terminal plate (connector 60a), supply and fixing of terminal plate (connector 30a)(mr), supply and fixing of ryb rotary switch(volt selector), supply and fixing of single phase preventer(20 to 30 hp), supply and fixing of single phase preventer(7.5 to 15 hp) (mr), supply and fixing of 15 amps relay (mr), supply and fixing of 23 amps relay (mr), supply and fixing of 33 amps relay, supply and fixing of 25 amps contactor, supply and fixing of 16 amps contactor(mr), erection of panel board & ms box (outdoor type) (gulbarga pred, pg.no.57, lt.no.12.2), supplying and fixing angle iron frame work fabricated out of m.s. angle iron and m.s. flat with bolt, washer etc and painted with 2 coats of red oxide and then two coats of approved paint 75x75x6mm (pwd ele sr 2014-15, pg.no.49, lt.no.6.39.3), refilling available earth around pipe lines, cable in layers not exceeding 20cms in depth, compacting each deposited layer by ramming after watering with lead upto 50m and lift upto 1.5m including cost of all labour complete as per specification pre sr 2011-12, p-3,1-6., labour charges for laying u.g. cable upto 3.5 core 25 sq.mm as per pwd electrical sr 2010-11, p-68,1-1, class a pvc cable, lifting of struck up submersible pump set above 300 ft (bwssb sr 2017-18/o150g/sl no.27), lifting of struck up submersible pump set upto 300 ft (bwssb sr 2017-18/o150g/sl no.26), labour charges overhauling, lifting of submersible pumpsets, re-errection charges of pumping machinery including overhauling and painting, cable joint, g.l. pipe threading including transportation, labour charges (for over hauling), supply and fixing of ct coil 50/5 & 75/5, supply and fixing of blade set 25a, supply and fixing of blade set 16a(mr), supply and fixing of hylum brand hand plastic sheet 3mm thick with necessary nitches for fixing switches, regulators etc and fixing of exciting wood or metal box using nf screw , supplying and fixing polished wood board made out of not less than 15mm thick planks at both sides with planks made out of not more than 2 pieces and fixing the same to the wall using tapered wooden plugs screws etc, fabricating, supplying and mounting ms box made out 14 swg suitable for foor/wall mounting, fully weather proof with provision for better heat dissipation, provided with hinged front over equipped with temper proof locking arrangements with suitable size clamps with necessary cable entry pipe with gland and box should be finished with 2 coats of red oxide primer paint and finally finished with approved colour enamelled metal paint etc., com

CTN :40225499

17 May, 2025 NA

Guwahati - Assam

Tender For supply, installation and fittings of firefighting system along with related accessories for installation of 5tph rice processing unit at hojai under apart project - supplying, installation, testing & commissioning of electric driven pressurisation terrace pump suitable for automatic operation & consisting of following, complete in all respects, as required (25hp) 1680 lpm at 70 m head. horizontal type, multistage, centrifugal pump of cast of iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to is 1520., supplying, fixing, testing and commissioning of butterfly valve of pn 1.6 rating with bronze/ gunmetal seat duly isi marked complete with nuts, bolts, washers, gaskets conforming to is 13095 of following sizes as required : 100mm dia., supplying, fixing, testing and commissioning of butterfly valve of pn 1.6 rating with bronze/ gunmetal seat duly isi marked complete with nuts, bolts, washers, gaskets conforming to is 13095 of following sizes as required : 80mm dia., providing, installation, testing & commissioning of non-return valve of following sizes confirming to is: 5312 complete with rubber gasket, gi bolts, nuts, washers etc. as required: 100mm dia., construction of terrace tank of 20000 ltrs capacity for wet riser, providing & fixing of 25mm dia. gunmetal air release valve with all fittings and forged ball valve on header complete as required., "providing & fixing following size pressure gauge(0-15 kg/cm2) complete with shut off valve duly calibrated before installation complete as required., providing & fixing reinforced neoprene rubber vibration eliminators/expansion joints(to provide relief from stresses at pipe flanges)suitable for upto 20 kg/cm2 pressure, complete as per specification.80mm dia., providing and fixing heavy duty aluminium armored cables 1.1 kva grade including necessary support clamps at ceiling level and connection legs complete in all respects. power cable 4 core 10 sq.mm, providing and fixing 6 swg dia g.i. wire on surface or in recess for loop earthing as requried., hydrant system, providing, laying, testing & commissioning of c class heavy duty ms pipe conforming to is 3589/is 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 25 mm dia, providing, laying, testing & commissioning of c class heavy duty ms pipe conforming to is 3589/is 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 65 mm dia, providing, laying, testing & commissioning of c class heavy duty ms pipe conforming to is 3589/is 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 80 mm dia, providing, laying, testing & commissioning of c class heavy duty ms pipe conforming to is 3589/is 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 100 mm dia, supplying & fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap & chain as reqd. for suitable dia ms pipe connection conforming to is 904 as required : 3 way - 100 mm dia m.s. pipe, providing and fixing fire brigade suction hose coupling (draw out connection) with nut for female c

Central Government/Public Sector

CTN :40220388

13 May, 2025 NA

Valsad - Gujarat

Tender For supply of aluminium impeller for oil cooling blower unit.centrifugal design for 3-ph ase loco motive as per rdso spec. no.rdso/2016/el/spec/0123, rev-0 issued on 05/10/2016 a nd drawing no- rdso/2016/sk-6/el/spec/0123. [ warranty period: 30 months after the date of d elivery ]

CTN :39671736

10 May, 2025 NA

Nilgiris - Tamil Nadu

Tender For corrigendum : supply of fan impeller aluminium as per cfa specimen along with ms shaft

State Government

CTN :40095274

19 May, 2025 NA

Birbhum - West Bengal

Tender For providing electro-mechanical accessories and others at pump house- i and ii for bahadurpur w/s scheme at murarai -i block under bolpur mechanical division phe dte. - supply and delivery at site of the following submersible pumping machinery and electrical accessories as per approved vendor list of phed, submersible pumping machinery directly coupled with water proof suitable size motor having following specification :- pump:duty condition -25.74 m3/hr, head- 57 mtr, shaft-stainless steel, impeller- s.s / gm, outlet size: 65mm / 80mm., motor:submersible type 3 ph , 50hz, 415 volt 10% 2900 rpm motor must be suitable for operation with star delta starter.(test certificate along with characteristic curve should be submitted at the time of delivery)., 1.1kv grade 4 sq.mm x 3 core water proof flat submersible cable for above pump-motor set., 1.1kv grade 10 sq.mm 3 core xlpe insulated aluminium armoured cable conforming to is 7098 (part-i) 1988, with upto date amendments., supply and delivery of the following valves, pipes and gauges etc at site, 3mtr long 80mm dia upvc standard type column pipe [cream color] with both side threaded and one end side socketed with registered kpmg, 1.5 mtr long 80mm dia upvc standard type column pipe [cream color] with both side threaded and one end side socketed with registered kpmg., 80mm dia. ci top & bottom adopter., heavy type suitable dia. ms suspension clamp along with nuts bolts and washers., 80mm dia. cidf non-raising sluice valves, pn 1.0 rating (conforming to is:14846) for delivery pipe line and wash out line.(moc & tc needed for valve)., 80mm dia. cidf single door swing non return valve, pn 1.0 rating (conforming to is:5312).(moc & tc needed for valve)., cidf 90 bend- 1no., ci flanged tee- 1no., blank flange-1no., ci/ ms flanged short piece 0.50 mtr.-1no, ci/ ms flanged pipe 1mtr.- 1 no. etc (as per is specification and certification registered) for construction of delivery pipe line and wash out line, heavy type 250mm dia./suitable split type tube well cover with clamping arrangement including supply of nuts, bolts and washer as per departmental design., anti snapping safety device for pump set by supplying suitable size of ms angle busket and nylon rope of required length including supplying of nuts, bolts and all other materials, 150mm dial pressure gauge [range 0-7kg/cm ] with glycerine filling inside the dial including brass cock and fitting complete [this cost includes 15mm. dia g.i. pipes and specials]., making brick pillar 0.25 x 0.25 x 0.75 mtr/suitable hight for supporting of valves and pipes with 12mm thick plaster and net cement finish complete., making cc foundation for support of the kiosk box after excavating the earth upto a depth of 0.6 mtr below the gl including supply of all materials complete with 12 mm thick cement plastering with net cement finishing complete as per direction of eic (size: 3 x 1 x 5)., suitable kiosk box for cable connection of submersible pump motor set with degree of protection ip 65 including suitable legs and 6 nos. al. bus bar for 32 amps and all necessary earthing arrangement and insulator as per direction of eic., laying of one no. cable 10 sqmm 3 core ( departmental supply) in underground trench 460 mm wide x 760 mm average depth, with brick protection on the top of thecable with 8 (eight) nos. bricks per metre, including filling the space between the brick & cable and also the trench with shifted soil, leveling up and restoring surface duly rammed., carrying and fixing three phase submersible pump 7.5 hp mug starter as per direction of eic ., installation of submersible pumping machinery to newly sunk tubewell along with column pipes (as required), top cover, valves, and specials of above with protection pipe and supply of ms clamp, nut bolt, cable gland socket etc. making inerconnection of the pump delivery line to pump collecting main line near tubewell with supply of all necceasary pipe, reducer/enlarger, gi/ms specials etc.

CTN :40090950

07 May, 2025 NA

Kalpakkam - Tamil Nadu

Tender For supply of spare parts for centrifugal pumps , bpo type from sl no-1 to 9.make process pump, model - pphb pphbs, serial nosh11c54m,h13f19m,h10l26m,h10g23m , oil level indicator, moc aluminium., part no -14 , bearing housing.moc-ss-304,part no-22 , bearing cover drive end , moc-ss 304,part no-19 , bearing cover far end ,moc-ss304.,part no-24 , gland plate,moc- ss 316 cf-8m .part no10 , gasket for impeller,moc-ptfe.,part no-5 , nut gasket impeller,moc- ptfe ,part no-4 , gasket for casing,mocptfe.,part no-7 , mechanical seal,moc-. ss-304 rott sic sic plan .part no-9 , spare parts for centrifugal pumps , bpo type from sl no-10 to 18. model - pph2m pph2 pph4m, serial nos h11c57m, h13112m, h11c62m oil level indicator. moc-alluminium. , part no -14 , bearing housing.moc-ss304., part no -22 , bearing cover drive end ,moc-ss304,part no -19 , bearing cover far end ,moc-ss-304.part no -24 , gland plate,ss-316 moc-cf-8m ,part no -10 , gasket for impeller,moc-ptfe,part no -5 , nut gasket impeller,moc-ptfe,part no -4 , gasket for casing,mocptfe.,part no -7 , mechanical seal,moc-. ss-304 rott sic sic plan .part no -9 , spare parts for centrifugal pumps , bpo type from sl no-19 to 27. make process pump, model - pph9, serial nos of the pumps h10g31m, h11c65m . oil level indicator. moc- aluminium. part no -14 , bearing cover drive end ,moc-ss-304., part no -19 , bearing cover far end ,moc-ss-304,part no -24 , gland plate, moc-ss-316-cf-8m ,part no -10 , gasket for impeller,moc-ptfe.,part no -5 , nut gasket impeller,moc-ptfe.,part no -4 , mechanical seal, moc-. ss-304 rott sic sic plan . part no -9 , spare parts for centrifugal pumps ,bpo type from sl no-28 to 36.make process pump, model - pph1, serial nos h12801m, h12802m . oil level indicator. moc- alluminium. ,part no -14 , bearing housing.moc-ss-304.,part no -22 , gland plate, moc ss316 - cf-8m ,part no -10 , gasket for impeller,moc-ptfe . part no -5 , gasket for casing, moc-ptfe.,part no -7 , gland packing, moc- tiwa ,part no -10

Central Government/Public Sector

CTN :39966458

09 May, 2025 NA

Ahmedabad - Gujarat

Tender For supply of aluminium impeller for oil cooling blower unit. centrifugal design for 3-phase loco motive as per rdso spec. no. rdso/2016/ el/spec/0123, rev-0 issued on 05/10/2016 and drawing no- rdso/2016/sk-6/el/spec/0123. [ warranty period: 30 months after the date of delivery ]

Central Government/Public Sector

CTN :39950718

12 May, 2025 NA

Delhi - Delhi

Tender For supply of aluminium impeller for oil cooling blower (centrifugal type) for 3-phase locomotives as per rdso specification no. rdso/2016/el/spec/0123 rev. 0 and drawing no. rdso/2016/sk-6/el/spec/0123

CTN :39801732

08 May, 2025 NA

Multi City - Multi State

Tender For supply of aluminium impeller for oil cooling blower unit specification/drg no. clw/es/3/sk-1/0649. [ warranty period: 30 months after the date of delivery ]

Low Voltage Motor Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

Central Government / Public Sector

Central Government/Public Sector

State Government

Central Government/Public Sector

Central Government/Public Sector