Get complete information related to latest Lt Switch Repair Tenders . from India at Classic Tenders. Search the best available tenders from Indian government tenders, domestic Lt Switch Repair Tenders , private tenders, online tenders, tender invitation notice, business tender notices, online tenders and bidding Lt Switch Repair Tenders.
Tender For supply of repair to tata mobile 088271h - labour charge for servicing and replacement and fixing of unserviceable filter , engine oil 15w40 , diesel fuel filter , oil filter , coolant , steering oil , break oil , clutch oil , air filter , labour charge computerised wheel alignment and wheel balancing , labour charge for removing and refixing after fuel tank cleaning , labour charge servicing replacement defective parts of door and making up the bends and rubber hose , labour charge servicing and replacement of unserviceable front disc , brake rubber boot , labour charge for servicing external clogging of intercoolers and radiator making up defects as reqd , material and labour for servicing and replacement of unservicable drive belts , labour charge serving and making up defects for bleeding of clutch actuation system , labour charge servicing and replacement of necessary defects for proper sealing of air intake system , labour charge servicing and tightening all fasterners , fasterners with acessories , labour charge for checking and replacement as necessary defects in electrical system ensure usage of genuine fuses with correct ratings condition of fuse and relay holding , fuses with relay , labour charge for check steering wheel play check for proper condition of ball joints and rubber boots of tie rod drag link for looseness damage , rubber boots of tie rod , labour charge for complete servicing of door with necessary replacement , labour charge for checking of wiper assembly and replacement of unserviceables parts and painting , wiper motor stator rewinding , wiper motor armature winding , wiper motor fxing materials , wiper linkage , wiper blade , wiper arm , labour charge for complete dismantling and servicing of rear load leaf spring and bending and refitting the same and replacement of unserviceables parts , rear spring bushing kit , centre bolt , clamp , labour charge for complete burnt starter from vehicle and replacing following parts , solenoid switch , carbon brush set , bushing set , fitting kit , labour charge for complete dismantling of steering from the vehicle , replacement of steering center line assy , replacement of steering center line pin kit , material and labour for rectifing denting filling painting as existing , material and labour for servicing washing and greasing
Tender For supply of motor limit switch , mnx80 power contactor , mnx140 power contactor , 3 pole power contactor mnx 25 to 25a , bimetal overload relays , bimetallic overload relay , power contactor mnx 32 to 32a , 3p air break power contactor mnx 40 to 50a , 3p air break power contactors mnx 50 to 50a , thermal overload relay , add on block mno 22e , relay thermal ol with single phasing proteclion , 3p air break power contactor mnx 09-09a , add on block mno a1 , bimetallic overload relay .45-0.75a , power contactor spare kits , 3p air break power contactor mnx 70 to70a , 2no 2nc auxcontact block for mnx 9 to 40a , 1no 1nc auxcontact block for mnx 9 to 40a , spare contact kit for mnx 18 , spare kit without coil for contactor , spare contact kit for mnx 40 , spare contact kit for mnx 80 , spare contact kit for mnx 95 , spare kit without coil for contactor type mnx110 , spare kit without coil for contactor type-mnx140 , thermal ol relay type-mn2 , bimetallic overload relay 0.9 to 1.5a with sppty mn2 , bimetallic overload relay 2 to 3.3a with spp ty mn2 , bimetallic overload relay 4.5 to 7.5a with spp ty mn2 , bimetallic overload relay 66 to 110a with spp ty mn5 , pole assembly , breaker jaw contact , test or isolated position micro switch right , test or isolated position micro switch left , fixed arching contact , spring charging motor , closing coil , shunt release , power contactor mnx18a , power contactor complete assembly mnx110 , spare contact kit for 3 pole power contactortype mnx32 , thermal overload bimetal relay with single phasing protection mounted on mnx type contactor , thermal overload relay mn5 , main contactor type mnx95 , 1no aux contact block for mnx 9 to 40a , service position micro switch left , thermal over load relay type mn2 , closing coil 240v dc acfor c-power 1250a , spare contact kit for mnx 50 , spare coil for mnx 95 to 140 , bimetallic overload relay 180 to 300a , breaker cradle terminal 4000ah , service position micro switch rigth , spare coil for mnx 45 to 80 motor limit switch,for c-power, air circuit breaker, 4000ah,415v,50hz,3p,50hz,edo spare, make: l&t, 3p air break power contactor,415v,mnx 80-80a with aux.cont-2no+2nc& coil-240v ac, contactor,415v,mnx 140-140a with aux.cont- 2no+2nc& coil-240v ac, 3p air break power contactor,415v,mnx 25-25a with aux.cont-1no& coil-240v ac, make l&t, bimetallic overload relay(6- 10a)with spp,type-mn2, make: l&t, bimetallic overload relay(20-33a)with spp,ty-mn2, make : l&t, 3p air break power contactor,415v,mnx 32-32a , coil-240v ac, 3p air break power contactor,415v,mnx 40-40a , coil-240v ac, make : l&t, 3p air break power contactor,415v,mnx 50-50a , coil-240v ac, thermal overload relay mn2, range 3-5amp, make-l&t, add on block(2no+2nc)-220v ac,mno 22e, relay thermal o/l with single phasing proteclion range 1.4-2.3amp, make : l&t, 3p air break power contactor,415v,mnx 09-09a with aux.cont-1no& coil-240v ac, add on block(4no)-220v ac,mno -a1, make : l&t, bimetallic overload relay(.45-0.75a)with bid details/ 2 / 54
Tender For design, engineering, manufacture, assembly, testing before dispatch, supply and delivery in well packed condition of 11 kv,800a, sc level 40ka for 1 sec load break switch panel ,scope also includes dismantling and removal of existing (old) 02nos.lbs panels of ngef make, disconnection of power cables and control cables and erection of new panels, power cable & control cable connection, bus bar connection, panel connection, testing, and commissioning, lbs shall conforms to iec62271- 102:2003 . detailed scope and gad,bom is as per attached annexures-i to iii
Tender For procurement of siemens make electrical spares at unit -7,8 ssctps,suratgarh - type 3vm1225-5ee32-0aa0, rating 250amps, 3vm mccb, thermal-magnetic trip unit, ir=175a, 415v ac, 50 hz , power contactor sicop 3tf, type: 3tf52 02-0ap0 with 240v ac coil rated current 170amp with aux. cont. 2no + 2nc , sicont plus aux. contactor with 230v ac type:3th3040 0ap0, aux.cont.4no , sicont plus aux. contactor with 110vac coil type: 3th3022 0afo aux.cont.2no+2nc , power contactor sicop 3tf rated-415vac/9a, type: 3tf3010-0af0, coil vtg-110vac , contactor, 225a, 3rt10 64-6la06(3rt19 65-5ap31), 220v ac , contactor, 3rt2017 1ap02, 12a, 220v ac , contactor, 10a, 3rh21 22-1ap0, 220v ac , mcb, 16a tp (c'class) , electronic motor protection relay, 3rb20 56-1fc2 (50-200a) , two way position selector switch, 3sb50002ab01 , contactor kit, 225a, 3rt10 64-6la06(3rt19 65-5ap31), 220v ac 3rt1965-6a , air breake (power) contactor, 12a, 110v ac coil 3main+no and 2no+2nc aux. contact, model no. 3tf3110-0af0+ 3tx4010-2a + 3tx4001-2a+3tx4001-2a , air break (aux.) contactor relay 4a, 110v , model no. 3th30 40-0af0 , power contactor 63a,415v ac coil 3 main model no. , 3tf4702-0af0za01 , power contactor 45a,415v ac coil , model no. 3tf4602-0af0za01 , power contactor 32a,415v ac coil 3 main with 2no+2nc model no. 3tf3400-0ar0+ 3tx4010-2a+3tx4010-2a+3tx4001-2a+3tx4001-2a , mccb 80a, 3p, 415v ac, 50ka , model no. 3vm1180-5ed32-0aa0 , fan motor thermal o/l relay (r/r 1.0 to 1.4a) , model no. 3ua5000-1a , pump motor thermal o/l relay (r/r 3.0 to 5?) , model no. 3ua5000-1f , add on block 3tx 4010-2a, 1no model no. 3tx 4010-2a,1 no , add on block 3tx 4001-2a, 1nc model no. 3tx 4001-2a,1 nc , power contactor with add on block contactor : coil-220v dc type:3rt2015-1bm42 add on: type:3rh2911-1aa10 , over load relay with spp: , range : 1/1.6a/1.1-1.6a , olr: type: 3ru2116-1ab0 with standalone assembly support , 3ru2916-3aa01 , contactor relay , 3rh2122-1bm40 coil-220v dc2no+2nc , pole discrepancy timer(contactor mounted) , coil:220 v dc , range 1-60 sec, on delay , contactor: 3rt2026-1a08k timer:3rp1511-1aq308k
Tender For corrigendum : supply of outdoor type rmu11kv 630a 21ka 3sec both side extensible motorised scada compatible 2 nos load break switch and 1 no vacuum circuit breaker as per specification with metering module with bus pt auxiliary trfr batterycharger/battery ccv met
Tender For corrigendum : supply of 415v, utilization category ac23a, 630a local isolator cabinet in sheet steel enclosure complete with 630a, 3 pole load break switch. 2. shall be with side operated handle, padlocking facility, prebreak micro switch having 1no+1nc contact. 3. micro switch contacts shall be wired to 4 sq mm tb for external termination. 4. provision of padlock system having sufficient space to lock the isolator at off position by minimum two agencies at a time. 5. complete with both power & control circuit wiring with all insulators, bus bars and control terminal blocks. 6. detachable bottom gland plate for entry of cables from bottom. 7. front door shall be hinged and inter-locked with the isolator in 'on' position. the front door should have a minimum 3 mm thickness perspex/triplex window for observation of position of contacts. 8. isolator should confirm to iec 60364 standard. 9. the dimensional drawing of the local isolator cabinet or product catalogue showing mounting arrangement of the components should be enclosed along with the offer. 10. isolator cabinet should be provided with rain canopy. 11. any isolator parts should not be made of aluminium/aluminium alloy. 12. isolator cabinet shall be metal enclosed suitable for wall fixing using 4 welded fixations, dust and vermin proof and shall be provided with degree of protection as ip-55. 13. provision for three distinct parallel busbar per phase for termination of three nos of 240 sqmm aluminum cables for incoming and two distinct busbar per phase for termination of 120 sqmm copper cable. 14. all hardware used in isolator cabinet shall be corrosion resistant. 15. minimum clearance between the live parts and detachable bottom cable gland plate shall be 400mm. 16. cabinet should be painted with alkaline resistant epoxy paint. 17. isolator cabinet shall have provision for earthing at two separate and distinct points. 18. each isolator cabinet should be supplied with panel keys., push button station specification: 1. pbs made of 2mm sheet steel enclosure with rain canopy, protection: ip-65. 2. 01 no. of green colour start pb with 1no+1nc contacts, 01 no. of red colour stop pb with 1no+1nc contacts, 01 no.of increase pb with 1no+1nc contacts <(>&<)> 01 no.of decrease pb with 1no+1nc contacts. one emergency stop push button with 1no+1nc contacts (push to lock type) shall be provided. size of each push button is of 22.5mm diameter. inscription plate for all push buttons. 3. pb shall be wired with 2.5 sq.mm. copper wire to 40 nos. serially numbered terminal blocks (tb) of elmex make having tb-5-6, 7-8, 11-12, 13-14 <(>&<)> 17-18 shorting link. 4. two nos. of cut out of size 72x72 mm for ammeter and rpm meter shall be provided. 5. 'on','off' <(>&<)> 'trip' indication led lamps in red, green <(>&<)> amber colour respectively with inscription plate to be provided. 6. all push buttons, elements, led lamps <(>&<)> cutout for ammeter <(>&<)> rpm meter shall be on the hinged door of the pb station. 7. pb station shall be weather proof, neoprene rubber gasket suitable for outdoor application. 8. 2nos. of earthing studs to be provided. 9. left side hinged door shall be provided with flexible braided copper earthing. 10. pbs shall have 04 nos. of corrosion free bracket suitable to fix on vertical surface. 11. detachable gland plate to be provided. 12. the push button shall be painted with one coat of red oxide primer <(>&<)> two coats of zinc chromate primer and finally finished with stoving enamel grey paint. 13. the push button station shall be generally in line of enclosed drawing (fig-2). 14. party to submit the drawing along with the offer for technical scrutiny.
Tender For supply, delivery, commissioning and testing of 3 phase, 11kv/0.433 kv, 50hz, 160kva copper wound, oil colled outdoor distribution transformer, 11kv, 95sqmm, 3 phase, 4 core aliminium armoured, lt supply distribution control panel, 11kv, 630 amps, 3 phase lbs (load break switch), remoured power cables, ci earthing necessary accessories for improvement of 3 phase incoming voltage supply to the inline booster, tanker filling stations at kondapur, white field in white field section of kondapur sub division-i under operation and maintenance division xv, durgamcheruvu.