Latest machined shaft Tenders | Government machined shaft Tenders

Central Government/Public Sector

CTN :40134811

05 May, 2025 16.74 Lacs

Chandrapur - Maharashtra

Tender For supply of pullen make 120 hp submersible pump spares - stator without widing 120 ,2900 rpm part no. of oem 1131ci2p120hp , rotor complete 120 hp 2900 rpm part no. of oem 1135ci2p120hp , winding wire 120hp 2900rpm part no. of oem 11092p120hp , bearing bush for upper housing part no. of oem ci1130 , bearing bush for lower housing part no. of oem ci1137 , thrust bearing complete part no. of oem 1147 , mechanical seal part no. of oem ci1172 , motor base compelet, ci part no. of oem 1119cia , suction case complete part no. of oem ci39003p11a , pump shaft for 6 stag part no. of oem ci39002p6 , nrv body compelet, ci part no. of oem ci39025a , middle sleeve bowl sleeve part no. of oem ci39021 , impeller part no. of oem 39005

CTN :40135848

17 May, 2025 NA

Hooghly - West Bengal

Tender For supply of other section , m and l for two coats of synthetic enamel paint over a coat of red oxide primer on new steel surfaces width or girth exc 10 cm including preparation of surfaces all as specified and as directed. , m and l for three coats of white washing on new plaster and unplaster of wall surfaces including preparation of wall surfaces complete all as specified and as directed. , s and f steel stainer for sewage sumps of different pores as specified and directed by engineer in charge , suppy of stand by non clogging pump of 5hp 1520 lpm with all accessories and fittings as specified and directed by engr in charge , heavy duty double tank type chemical dosing system consist of service tank 150 ltrs capacity with dosing system plunger type , s and f gi strip 25x4mm as earthing lead bolts nuts checknuts and washers all as specified and directed , material and labour for earthing complete with galvanized steel plate electrodes of size 600mm x 600mm x 6mm thick , pumping out sewage water from the existing sumps of sewage plant pump house with the help of non clogging of pump any kind capacity of pump set not less than 2160 lpm , lifting the non clogging pump set electrically operated by 15hp 20 hp 3 phase motor incl column pipe line shaft etc , dismantling of non clogging submersible pump of capacity 15hp 20 hp for comprerhensive maintenance and if required taking out burnout old winding from the stator , lowering complete the non clogging pumping set and reflixing the motor carefully including connection and testing , pumping out sewage water from the existing sumps tanks of stps mbbr technology with the help of non clogging , cleaning of 1.2 mld sewage treatment plant after pumping out sewage water from the existing sumps , lifting the non clogging submersible pump set electrically operated by 3.7 hp 3 phase motor incl column pipe line , dismantling of non clogging submersible pump of capacity 3.7 hp and taking out burnout winding from the stator of motor and rewinding with pvc copper wire , dismantling of electric sewage induction motor 3.0 hp ac 3 phase 415 volts from site after disconnecting from pump , dismantling non clogging pump set of centrifugal type 3.0 hp induction motor ac 3 phase 415 volts , dismantling of electric induction blower motor 5.0 hp ac 3 phase 415 volts for comprehensive maintenance from site after disconnecting , dismantling of electric induction blower motor 30.0 hp ac 3 phase 415 volts for comprehensive maintenace from site after disconnecting from blower electric connection , material and labour for pcc 1 3 6 type c2 using 40mm graded stone aggregate for foundation etc , m and l for taking out comprehensive maintenance of existing unserviceable air blower of any make of capacity 125 cubic hr to 188 cubic hr with taking out of electric cable , supply only gear oil ep 90 complete all as specified and as directed by engineer in charge. , supply only air filter suitable for existing one complete all as specified and as directed by engineer in charge. , supply only belt as per existing model complete all as specified and as directed by engineer in charge. , supply only bearing as per existing complete all as specified and as directed by engineer in charge. , supply only set of rotor with hub as per existing model complete all as specified and as directed by engineer in charge. , m and l for finding out defect of stps panel and taking out burnt interconnection wiring including u.s and serviceable component for re use including rewiring of panel , supply and fix in repairs flexible flat pvc copper couductor stranded submersible cable cores 1100 volt grade 4 sqmm 3 bid details/ 2 / 41 core , supply and fix in repairs flexible flat pvc insulated pvc couductor stranded submersible cable cores 1100 volt grade 10 sqmm 3 core , s and f round strand steel wire rope dia 12 mm and connected clamp nut bolts fixed complete all as specified and as directed by engineer in charge. , s and f submersible pump ful

Central Government/Public Sector

CTN :40136030

07 May, 2025 NA

Singrauli - Madhya Pradesh

Tender For supply of item_ 10_ m2297730479_ 100248897_ stub shaft, ip rotor balancing , item_ 20_ m2297730483_ 100248897_ stub shaft, ip rotor

CTN :40140724

17 May, 2025 NA

Kalyani - West Bengal

Tender For supply of proof machined shaft machining as per drg. no. k- 6533/2

CTN :40141013

17 May, 2025 NA

Jalandhar - Punjab

Tender For supply of kit pad assy front , brake rotor brake disc 4x4 , assy shaft universal joint , front fog lamp lh , front fog lamp rh , assy water valve , assy intake hose , coolant pipe hose , clock spring assy , gasket elbow by pass , mini fuse 10a

CTN :39834852

28 Apr, 2025 NA

North 24 Paragana - West Bengal

Tender For bid to ras bid to ras tender for supply of liquid gasket lg 7 , 150g , dust indicater , hose , o ring , body air cleaner , stator assy , rotor assy , fuel cut off valve , hose w s to valve port 1 , hose , hose , bearing main std 1 eng set , bearing main us 0.25 1 pair , main bearing thrust , switch , pin , valve exaust , valve intake , seat exaust valve insart , seat intake valve insert , spring valve ex , stop cable , hand priemer , sealing ring for 13 & 15 , sealing ring for 4 , valve , spring , nut , hose fuel , bolt , hose , cylinder head gasket (kit k1) , gasket , gasket , sealing ring , hose , oil cooler assy , cartridge oil filter , spill hose ( 5 pieces) , banjo bolt , clip , pin piston , piston ring assy , bearing crankpin std(sp) 1 pr , bearing crankpin us 0.25 , pair , snap ring , joint bolt , delivery valve assy , gasket , o ring , o ring , o ring , oil seal , pump element , seal ring , screw plug , bolt , housing rocker , switch , starter (deloc remy 11 teeth) , starter(l tvs 11 teeth) , hose , spring , seal bearing , o ring , fitting grease , pin cotter , pin , yoke , shaft , gasket , o ring , o ring , clip , bolt , nipple , gasket , bolt joint , cap , o ring , gasket , valve , gasket , gasket , gasket , gasket , stud , stud , stud , screw , bushing , stud , seal oil , gasket , o ring , knob , lever gear shift , bolt reamer , hose , gasket , lock , o ring , screw , gear guide (5m) , gear driven 1st , gear driven 2nd , race inner , race inner , gear driven 3rd , shaft intermidiate , holder , spring interlock , gasket , bushing , lock , fork assy , seal oil , clamp , clip , boot , cover , bushing , collar , o ring , screw , gasket , gasket , o ring , breather , boss , ring snap , stud , o ring , washer spring , flange top , flange bottom , cage bearing rh , gear bevel , ring seal , seal bearing , gasket , nut , pin cotter , pin , shaft , pin , stopper , gasket , o ring , o ring , element filter , flange , gasket , cover , cover rh , o ring , o ring , packing , bushing , spring rubber coated , o ring , bolt , seat , bolt , o ring , bolt (lm) , grill radiator , bolt , bolt , washer spring , washer spring , rest arm , clamp , bolt , hydraulic tank assy , quick drop valve rh , tube lh , seal , seal dust , pin dowel , o ring , hose , flange , plate , tube , bolt , edge cutting , bit end rh , bolt (lm) , washer spring , nut (lm) , pin cotter , lamp assy , horn switch , smart alarm , lamp helogen , terminal positive , ammeter , lamp indicator ewt , instrument panel

State Government

CTN :40123825

28 Apr, 2025 NA

Akola - Maharashtra

Tender For procurment of rotor shaft assembly of pa fan ndv bab22 in 2x250 mw units at paras tps

State Government

CTN :40100392

05 May, 2025 NA

Bankura - West Bengal

Tender For different item of workunder pwm scheme - agglomerator machine: (24 x30 )specification: applicability: all thin plastics, multi-layer plastics and styrofoamautomation: semi-automaticinner diameter: 24 height: 30 bearing housing type: 2 bearings production capacity: 80-100 kg/hblades & sizes: 8 no. (4 rotter blades & 4 fixed blades)blade material: camani blades rotor shaft:100 mm equi balanced shaftmotor: 30 hp motor & starter body:12 mm ms sheet and 2 mm ss sheetstructure: heavy mild steel frame weight:1100 kg (approx.)overall size: w 78 x l 109 x h 48 inch on site trainning maintenance: one year from the date of installation. [rates are inclusive of supplying, fitting , fixing, installation of machine or any others incidental charges with electrification, transportation, all taxes including labour and materials complete], plastic gatta making machine : hellical gear box 225(omex), motor 30hp motor & 15hp heaters on site trainning maintenance: one year from the date of installation. [rates are inclusive of supplying, fitting , fixing, installation of machine or any others incidental charges with electrification, transportation, all taxes including labour and materials complete], all in one granular machine :granual machine extruder 100 mm with heaters, heating panel motor &starter ss water granual cutter specification: dia of screw & barrel : 100mm (en 41 b and hardness 65 hrc)barrel design : plainscrew design : maddoc barrier (en 41 b barrier type screw size 100mm)ld ratio : 23:1main motor : 20 hp havells/crompton 1440 rpm motor & starter gear box : helical gear box ge 200 (omex)heaters : 15 hp ( 1 hp each) with heating panneloutput : 80-100 kg/hr. approx.(depends on raw material)die type : single manualtank : ss water tank for line of melted plastic granual cutter : 6 inch granual cutter with 2 hp motor control panel : controll panel for push button operationextruder machine size : 13.5 x 5.10 x 5 feet (l x w x h) extruder machine water tank size : 8 x 1.5 x 2.5 feet ( l x w x h)granual cutter size : 2 x 1.5 x 4 feet ( l x w x h) on site trainning maintenance: one year from the date of installation. [rates are inclusive of supplying, fitting , fixing, installation of machine or any others incidental charges with electrification, transportation, all taxes including labour and materials complete], mixer machine : 24" x 30", main motor : 20 hp havells/crompton 1440 rpm motor & starter gear on site trainning maintenance: one year from the date of installation. [rates are inclusive of supplying, fitting , fixing, installation of machine or any others incidental charges with electrification, transportation, all taxes including labour and materials complete], dryer machine machine : 24" x 30", main motor : 20 hp havells/crompton 1440 rpm motor & starter gear on site trainning maintenance: one year from the date of installation. [rates are inclusive of supplying, fitting , fixing, installation of machine or any others incidental charges with electrification, transportation, all taxes including labour and materials complete]

corporations/Associations/Others

CTN :40133173

05 May, 2025 NA

Bardhaman - West Bengal

Tender For procurement of spares of edwards make condenser vacuum pumps for tg and aux., dstps, dvc - intermediate plate, part no. 042070n01 for condenser vacuum pump, model no. shr22500, make- edwards, intermediate plate, part no. 032070n01 for condenser vacuum pump, model no. shr22500, make- edwards., rotor drive set for condenser vacuum pump, model no.-shr22500, shaft sleeve, part no. 860070n01 for condenser vacuum pump, model no. shr22500, make- edwards., shaft,part no.-092250n01 for condenser vacuum pump, model no.-shr22500, bearing coller ring, part no.-32700000n1 for condenser vacuum pump,model no.shr22500, grease thrower de side, part no.-33.70.0000.n9a, for condenser vacuum pump,model no.shr22500, grease thrower nde side, part no.-34.70.0000.n9a for condenser vacuum pump,model no.shr22500