Tender For supply of rate contract for the procurement of mechanical spares for conveyor system at barauni bp e e - ms c or u channels for conveyor track 2.5 m length , ms angle 40mm 40 mm and 6 mm thickness , conveyor flanges , conveyor flange joint gasket , twin arm stopper complete pair , plummer block with bearing ucp-213 ntn , plummer block with bearing ucp-212 ntn , double stopper set with pneumatic cylinder , duplex chain 1 inch 3m , duplex chain lock 1inch , duplex sprocket 17 teeth , duplex sprocket 19 teeth , duplex sprocket 21 teeth , duplex sprocket 23 teeth , duplex sprocket 32 teeth , duplex sprocket 38 teeth , duplex sprocket 42 teeth , linear bearing msa30sssfcn pmi make , linear bearing msa30essfc pmi make , loading boom roter drum , 14 teeth sprocket 60id , 14 teeth sprocket 65id , gear coupling , tapen bend strip , line divider arm , metal gasket 1 inch or 25 mm , metal gaskit 2 inch , metal gaskit 3 inch , metal gaskit 4 inch , gear box drive shaft 65 dia 710 length , 65 to 60 mm dia 940mm long en8 conveyor , chain pin for detachabe type chain , worm wheel for warm gears , shaft length 390 length and 40dia , sprocket 8 teeth 40dia , shaft lenght840 60dia , supply of cs 10mm dia 40mm length nut bolt , supply of nut bolt 16mm dia150 length , nut bolt 100mm length 12mm dia , supply of fastener nut bolt 12mm dia 100mm length , supply of fastener nut bolt 16mm dia 100mm length , supply of fasteners 16mm dia 150mm length , teflon roller ) /bid number : gem/2025/b/6501953 * /dated: 31-07-2025 & & / bid document 1 / 33
Tender For bi annual contract for routine cum breakdown and annual shutdown mechanicalmaintenance work of 2x25 mw turbine generator penstock system draft tube gate system fire fighting system etc at mahi ph 1 banswara
Tender For biennial maintenance contract mechanicalmaintenance for tmd-oph area water package for stgi stg ii and stage iii units stg i 2x300mw stgii 2x 500 mw stage iii u5 1x660mw units sgtpp wbpdcl
Tender For manning operation maintenance of external internal electrical and mechanicalmaintenance work at iit jammu, jagti and paloura campus jagti and pakloura campus
Tender For purchase of spares for mechanical seal in turbine and auxiliaries - mechanical seal assembly along with gland and sleeve for coltcs pump , seal face with part no. 1 for coltcs pump mechanical seal , o ring with part no. 2 for coltcs pump mechanical seal , spring with part no. 3 for coltcs pump mechanical seal , seat with part no. 4 for coltcs pump mechanical seal , o ring with part no. 5 for coltcs pump mechanical seal , shaft sleeve with part no. 6 for coltcs pump mechanical seal , o ring with part no. 7 for coltcs pump mechanical seal , driver with part no. 8 for coltcs pump mechanical seal , set screw with part no. 9 for coltcs pump mechanical seal , retaining ring with part no. 10 for coltcs pump mechanical seal , cover throttle bush with part no. 11 for coltcs pump mechanical seal , assembly fixture with part no. 12 for coltcs pump mechanical seal , hsh cap screw with part no. 13 for coltcs pump mechanical seal , assembly fixture with part no. 14 for coltcs pump mechanical seal , gasket with part no. 15 for coltcs pump mechanical seal , head screw plug with part no. 16 for coltcs pump mechanical seal , complete mechanical seal assembly for de side of the drip pump , seal face with part no. 1.1 for drip pump de side mechanical seal , o ring with part no. 1.2 for drip pump de side mechanical seal , thurst ring with part no. 1.3 for drip pump de side mechanical seal , spring with part no. 1.4 for drip pump de side mechanical seal , drive collar with part no. 1.5 for drip pump de side mechanical seal , spring sleeve with part no. 1.6 for drip pump de side mechanical seal , seat with part no. 2 for drip pump de side mechanical seal , o ring with part no. 3 for drip pump de side mechanical seal , cover with part no. 4 for drip pump de side mechanical seal , locking ring with part no. 4a for drip pump de side mechanical seal , retainer ring with part no. 4b for drip pump de side mechanical seal , o ring with part no. 5 for drip pump de side mechanical seal , sleeve with part no. 6 for drip pump de side mechanical seal , o ring with part no. 7 for drip pump de side mechanical seal , throttle bush with part no. 8 for drip pump de side mechanical seal , key with part no. 9 for drip pump de side mechanical seal , assembly fixture with part no. 10 for drip pump de side mechanical seal , hexagonal bolt with part no. 11 for drip pump de side mechanical seal , complete mechanical seal assembly for nde side of the drip pump , seal face with part no. 1.1 for drip pump nde side mechanical seal , o ring with part no. 1.2 for drip pump nde side mechanical seal , thurst ring with part no. 1.3 for drip pump nde side mechanical seal , spring with part no. 1.4 for drip pump nde side mechanical seal , drive collar with part no. 1.5 for drip pump nde side mechanical seal , spring sleeve with part no. 1.6 for drip pump nde side mechanical seal , seat with part no. 2 for drip pump nde side mechanical seal , o ring with part no. 3 for drip pump nde side mechanical seal , cover with part no. 4 for drip pump nde side mechanical seal , locking ring with part no. 4a for drip pump nde side mechanical seal , retainer ring with part no. 4b for drip pump nde side mechanical seal , o ring with part no. 5 for drip pump nde side mechanical seal , sleeve with part no. 6 for drip pump nde side mechanical seal , o ring with part no. 7 for drip pump nde side mechanical seal , throttle bush with part no. 8 for drip pump nde side mechanical seal , key with part no. 9 for drip pump nde side mechanical seal , assembly fixture with part no. 10 for drip pump nde side mechanical seal , hexagonal bolt with part no. 11 for drip pump nde side mechanical seal
Tender For purchase of various authorized, unauthorized (make) mechanical / electrical materials and various repairing / maintenance and amc works etc. for danteshwari maiya sahakari sugar factory limited balod (cg) 1250 tds sugar factory-authorized/non authorized (mechanical/electrical) material and repairing-1 dmssk ns 2025 3s1, power turbine belliss make hes 14 type, 3mw, t.a, set no-bm/4808/b (rate quated, by supplier must be servicing done by belliss india senior service engineer) spare, parts replacement done by supplier ,payment will be made on company price list., make -oem/autherised dealer, set 1, 2 dmssk ns 2025 3s4, t.g control pannel for power turbine belliss make hes 14 type, 3mw. spare, partsreplacement done by you. payment will be made on company price list.spare parts, replacement done by supplier,payment will be made on company price list. makeoem/jyoti power engineer's autherised dealer/ various technologies pvt ltd., autherised dealer, set 1, 3 dmssk ns 2025 3s6, dg set make- greaves, (type - tbd 2v12 mk.11, 320 kva - 2 no) (rate quated by, supplier must be servicing done by graves autherised senior service engineer) (with, spares parts) spare parts replacement done by supplier, payment will be made on, company price list. make-oem/ experienced contractor. (03 year exp. in sugar factory), set 1, 4 dmssk ns 2025 3s9, servicing of nhec make batch machine (model ng1250 2nos) rate quated bysupplier, must be servicing done by nhec service engineer spare parts replacement done by, supplier payment will be made on company price list (dynamic balancing not required)., make - oem/ sugarmax eng. technologies authorised dealer. (01 year exp in sugar, factory), set 2, 5 dmssk ns 2025 3s10, servicing of centinous centrifugal machine model nk 1100-5 nos rate quated, bysupplier must be servicing done by nhec servicing engineer spare parts replacement, done by supplier payment will be made on company price list (dynamic balancing not, required). make- oem/ sugarmax eng. technologies authorised dealer. (01 year exp in, sugar factory), set 5, 6 dmssk ns 2025 3s11, servicing of mill lubricating oil pump 18 points,model-lube-d make micro, precision (rate quated by supplier must be servicing done by microprecision senior, service engineer) spare parts replacement done by supplier, payment will be made on, company price list.make -oem/ experienced contractor. (02 year exp in sugar factory), no 5, 7 dmssk ns 2025 3s12 dynamic balancing of fibrizer, id, fd, sa fan & blower, centrifugal machine. make -, oem/ experienced contractor. (03 year exp in sugar factory) no 11, 8 dmssk ns 2025 3s13, servicing of feed pump ksb make model-had 50/14+std acce (rate quated by, supplier must be servicing done by ksb senior service engineer) spare parts, replacement done by supplier, payment will be made on company price list. make -, autherised dealer/experience contractor, no 1, 31, 9 dmssk ns 2025 3s14 filling of nitrogen gas cylinder of mill house max. press.-330bar cap.-37 ltrs. working, press.-170bar. make-experienced contractor. (01 year exp in sugar factory) no 8, 10 dmssk ns 2025 3s15, servicing of vaccum filter 8feetx16 feet (rate quated by supplier must be servicing, done by simplex engg senior service engineer) spare parts replacement done by you, ,payment will be made on company price list.make-oem/ experienced contractor. (03, year exp in sugar factory), no 1, 11 dmssk ns 2025 3s16, air compressure for centrifugal machine model no.-tc-100 bore-152.4mm rpm-650, press.-7kg/cm2 sl.no.-pec003453 (rate quated by supplier must be servicing done by, kirloskar pneumatic co.ltd. senior service engineer). make-experience contracter (03, year exp in sugar plant), no 2, 12 dmssk ns 2025 3s18 automation of imbibition water supply of mill no 3 work. make- autherised contractor, /experienced contractor no 1, 13 dmssk ns 2025 3s21, gun metal conversion basis casting and with machining as per sample rate qoutated, per kg without burning losses. make-experie