Tender For mtps- ii â mill plant division â reconditioning of pin bolt, pin bolt inserting bore of the roller tyre holding yoke frame assembly, roller tyre rtd cover plate, worn out surface of loading frame assembly, hydraulic shaft tension rods, renewal of worn out coal pipes, dismantling of flanges from old coal pipes & welded with new coal pipes, collar seating worn out portion of 90ë & 90ë+ 65ë coal bends, hard facing of dia 600 mm old coal bend, worn out seal cover seating distance spool piece flanges, fabrication & replacement of worn out deflector cone and coal feeding centre pipe (partial length) at inner side of classifier assembly etc⦠in coal mill â f/h
Tender For mtps- ii â mill plant division â reconditioning of pin bolt, pin bolt inserting bore of the roller tyre holding yoke frame assembly, roller tyre rtd cover plate, worn out surface of loading frame assembly, hydraulic shaft tension rods, renewal of worn out coal pipes, dismantling of flanges from old coal pipes & welded with new coal pipes, collar seating worn out portion of 90ë & 90ë+ 65ë coal bends, hard facing of dia 600 mm old coal bend, worn out seal cover seating distance spool piece flanges, fabrication & replacement of worn out deflector cone and coal feeding centre pipe (partial length) at inner side of classifier assembly etc⦠in coal mill â a.
Tender For nib for supply of hardware - super senior pellet mill, bearing cover frontforged steel, bearing cover rearforged steel, bearing setting ringforged steel, counter shaft assembly with pulley without beltwithout bearing & pedestal, die cover ringforged steel, die holder (steel) forgedforged steel, die holder assemblyforged steel, die holder rind rearsuitable for above alloy steel, die holder ring frontforged steel, feeder conditioner s. s. knifes.s. 304, thread 1/2" bolt per piece, feeder conditioner screw and paddle type feeder conditioner body s.s. approx. 1430 mm long s.s. -304 construction arrangement of single drive feeding end., front bearing spacer for t shaft, front scraper (roll stay assembly)forged steel with clamping stay, front scraper blades for pellet mill, pellet cooler air lockheight 450 mm/width 250 mm inlet/outlet 155 mm, pellet cooler eccentric assembly, pellet cooler sensor, pellet diesize:520 dia inner x 635 outer x 23.0 wider pellet :10/8 mm hole perforationmounting: tapper collar 12 deg on 620.6 dia or straight plug dia 610 diafixing 12-m 20 x 25 deep on 565 pcdmaterial: en 19c or 42crmo4 duly hardened & temp. polished, rc4=5, pulley assembly (fly wheel) 11 grooveforged steel, rear scraperforged steel, roll holder shaft (t shaft) assemblyforged steel, shearing pin, helical gear with hubone set containing 2 numbers, helical gear without hubone set containing 2 numbers, pellet mill sieve, screw for variable speed feeder conditioner for pellet mill, shear pin holding body, shear pun bush, spring set, teflon bush for main t shaft, pallet down spout, roll stay support stud (ss), pedestal sn 617, pedestal sn 619, pedestal sn 615, press roll assembly super senior, bearing cover, bearing retainer/nut for eccentric shaft km- 20, center bolt/roller stud (allen, bolt, head type design), circlip(dia 180 inside), clamping device tension ring(90x101x17) mm , distance ring, eccentric shaft, lock nut with lock washer for press roll eccentric shaft, lock washer (mb-20), nut for center bolt (lighting ring), press roll assembly complete with shell, bearing etc.suitable for above en-24 shell, press roll shell, setting ring, spacer (sealing ring), molasses mixer, molasses cutting knife with nutsuitable for above ni, hard duly balanced, paddle plane and loop typesuitable for above ni, hard duly balanced, spray pipe nozzle with nipple1.5 inch c class pipe, 3/8 inch nipple, mixer pipe (ss) suitable for molasses mixer, full circle hammer mill, beater (flat type) all equal weight, (big size 180 mm x 50 mm x 10 mm)ni hard, dynamically balanced, beater (flat type) all equal weight, (small size 140 mm x 47 mm x 06 mm), beater holder shaften, material, beater holding bush (size length 30 mm, in dia 20 mm, outer dia 30 mm), beater holding bush (size length 60 mm, in dia 20 mm, outer dia 30 mm), beater holding bush (size length 36 mm, in dia 20 mm, outer dia 30 mm), beater holding bush (size length 53 mm, in dia 20 mm, outer dia 30 mm), carrying rod for hammer mill 2 no of each set, door closing clamp set, hammer mill feeder, permanent magnet, sieve set3 mm, thick ms sheet with 3 mm, 2mm, 4mm, 5mm and 6mm perforations, sieve set clamping frame, hammer mill rotor, screw conveyor, screw conveyor, gravity pipe clamping 8 inch dia., gravity pipe clamping for above pipe8 inch dia, 16 gauge., gravity pipe m.s.8 inch dia, 16 gauge, 1 meter long, gravity pipe s.s.8 inch dia. 14 guage 1 mtr. long., pazama flap 3 way for distributionsuitable for 8 inch pipe, screw of different sizes, shaft suitable for joining the screw conveyor, chain conveyor, radler chain matching our existing chain conveyor. chain should 10mm thick links along with bushes and roller duly hardened., chain supporter with single bearing $nylon roller with shaft and bearing 1 no., lock ring, shaft 255mm long, chain supporter with double bearing $nylon roller with shaft and bearing 2 no., lock ring, shaft 255mm long, chain supporter (3-piece bush) $nylon roller without beari
Tender For corrigendum : supply of mini science lab and tinkering lab d d - constellationviewer , newtons disc , colour shadow , periscope , kaleidoscope , laws of reflection , corner mirror , infinity well , magic watertap , total internal reflection , fun with magnets , law of inertia , circle and ball , action and reaction , parrot in the cage , zoetrope , pin screen , floating ball , floating fan , tornado , hand pump , electric maze , floating magnets , simple camera , sum of the angles of a triangle , tangram , parking puzzle , organ pipes , area of rhombus , transverse wave pendulum , area of triangle , area of parallelogram , coupled pendulum , solar light , wind mill , shape of earth due to rotation , ke pe track , loop the loop , rope puzzle , corner mirror , newtons cradle , reflectiontransmission , hand battery , plant cell , cone run uphill , tower of pisa , lever , pulley block , wheel and axle , heat absorption , conductors and insulators , viscosity tube , rock and minerals , dna , lateral shift , area of trapezium , sum of angles of quadrilateral , electric bell