Latest motor starter spares Tenders | Government motor starter spares Tenders

CTN :41540182

01 Sep, 2025 NA

Bathinda - Punjab

Tender For supply of hose clamp , suction flange , impeller , carburetor assy , spark plug , recoil start assy , hose collar , flap valve , fuel pipe petrol , igb shaft , air comp drive shaft , blade wiper back door , front driver wiper assy , driven plate for clutch

Central Government/Public Sector

CTN :41464647

27 Aug, 2025 1.92 Lacs

Jamnagar - Gujarat

Tender For providing of repair and overhauling service - impeller blade (mat- casting) of the fwd engine room ventilation motor (415v, 3 phase, 9.3kw) found broken. impeller to be repaired/renewed and motor to be proved for satisfactory operation. , 05 in no general lightings and 05 in no flood lights at engine room, jr sailor washroom, waterjet compartment are not working. lights to be repaired/ renewed and proved for satisfactory operation , so toilet ventilation motor (415v, 3phase, 0.37kw) is not working view low winding insulation. rewinding of motor to be done and system to be proved for satisfactory operation.

CTN :41380242

29 Aug, 2025 NA

Garladinne - Andhra Pradesh

Tender For supply of cut section model of single cylinder petrol engine two stroke , cut section model of single cylinder petrol engine four stroke , cut section model of engine working five hp , demonstration board of fuel supply system of petrol , cut section model of cooling system , four stroke petrol mpfi engine setup for practice , training module for the crdi diesel engine , governer model , cut section of turbo charger , cut section model of inline fuel injection pump , cut section model of rotary type fuel injection pump , actual cut section of carburator with automobile parts , cut section model of rotary type injection pump , chart of fuel injection system , chart of cooling system , cut section model of synchromesh gear box , cut section model of five speed manual transmission , cut section model of gear box with diffrential , cut section model of constant mesh gear box , cut section model of mechanical brake system , cut section model of disc brake system two wheeler , model of air brake system , cut section model of hydraulic brake system two wheeler , cut section of monoblock pump , cut section of centrifugal pump , cut section of jet pump , cut section of submersible pump with 4 stages , different impeller board 70 cm x 85 cm , pelton turbine model , kaplan turbine model , centrifugal pump model , gear pump model model , hand water pump model , tubewell model model , deepwell turbine model , submersible pump model , reciprocating pump cut model , centrifugal compressor cut model , francis turbine model , rotary pump model , different types of pipe fitting with accessories , chart of submersible pump cut section 4 feet x 3 feet wall mounted , chart of monoblock pump cut section 4 feet x 3 feet wall mounted , chart of jet pump cut section 4 feet x 3 feet wall mounted , chart of centrifugal cut section 4 feet x 3 feet wall mounted , chart of sand filter cut section 4 feet x 3 feet wall mounted , chart of drip irrigation layout size 4 feet x 6 feet wall mounted , chart of sprinkler irrigation layout size 4 feet x 6 feet wall mounted , disc harrow model , disc plough model , indigenous plough model , mb plough model , self propelled reaper working model , threshing drum spike tooth type , threshing drum angular bar type , threshing drum loop type , mini rotavator , spike tooth harrow model , blade harrow model //bid details 2 / 48

Central Government / Public Sector

CTN :41185794

18 Aug, 2025 NA

Noida - Uttar Pradesh

Tender For corrigendum : supply of napier turbochargers spares for engine : : - thrust collar , ring seal ce , joint cone , joint for seal ring bush te , shim impeller adjustment , joint washer for seal ring bush ce , ring sealing for rotor te , bearing te , bearing ce , nozzle assembly , joint for mounting te and ce , speed prob , joint between turbine inlet or outlet casing , lock washer , outer cone , seal plate , washer for seal ring bush ce , ring seal te , seal ring bush te , seal ring bush ce , shim laminated peelable shim , seal plate shim , impeller adjustment washer , washer impeller drive , washer joint tc te seal ring bush , o ring for labyrynth seal plate , nozzle ring , joint for mounting foot and cover plate , plug anticorrosion , nut shaft end , lacing wire short for turbine blade , lacing wire long for turbine blade

Central Government / Public Sector

CTN :41265280

22 Aug, 2025 NA

Vijayawada - Andhra Pradesh

Tender For supply of impeller suitable for traction motor cooling blower(mvmt) 24 blade design as per clw specification no. clw/es/b-14/c or latest if any.

CTN :41030874

16 Aug, 2025 5.79 Crore

Karwar - Karnataka

Tender For corrigendum : procurement of fcbt and td auxiliary spares - bushing, countersunk screw m-8, rear thrust pad, gasket paronite (p)oh-(b)t s 1.0 gost 481-80, insert, shaft, impeller, ring, coupling, condensate pump, lock washer, oil retaining ring, turbine rotor assembly, two-half ring, gear shaft, flange, oil retaining ring, coupling, feed pump, jacket, nut, lock washer, intermediate bushing, spinner, nut m64 x 3, jacket, throttle valve, ring, ring, insert, reduction gear case, bolt - m10- 6g x 50, bolt - m10- 6g x 50, bolt - ml2-6g x 30, bolt - ml2-6g x 45, guide blade assembly, hex head nut m-12-6h, hex head nut m-14-6h, hex head nut m-16-6h, nozzle, plug, pocket, semi ring, screw, stud ml2- 6g x 25, stud m12- 6g x 30, stud m14 -6g x 30, stud m16-6g x 40, stud m12- 6g, nut, ring, rod, rod, safety valve, hand oil pump, male threaded-end straightway, bronze threaded-end angle stop valve, hand pump filter, oil indicator, rotor assembly, thrust disk, gland case in two halves, four segment sealing ring, reduction gear rotor assembly, reduction gear rotor, gear, roller, coupling, lock ring, coupling roller, nut m24x1.5-6h 05 06, gear wheel, key, setting ring, ring of two half, spherical washer, cover, gasket, slide valve, special nut, axle box, stud ?8-6g?22 56 029, ring 8?12, cap, gasket, flange, bushing, drive gear, bushing, bushing, bushing, bushing, spring coupling, pin 4?15, bracket, through woven stuffing, key 5?5?30, drive gear, bushing, pin 2?14, gasket, gasket, screw-in union, pin, plug, screw ?6-6g?10 14? 029, lever, jacket, slide valve, bellows, piston, spring, slide valve, speed regulator spring, tension screw, bushing, yoke, ring 2-43.8-4.1, spring, lower bushing of driven screw, lower bushing of driving screw, thrust plate (end thrust bearing), pump half-coupling, flat spring, gasket sail cloth no.1(p)b code no.11102 grade 1,100 cm wid, gasket rubber (i)p(p)-2025 s 2.0, sheild in two half, support pad, guide blades & steam shield, bushing, floating ring of two halves, support pad, sheild, support plate, support plate, thrust pad, valve seat, ball d84, lock washer a.6.08?18?10?, lock washer a.8.08?18?10?, ball link, spherical end thrust bearing in two half, spring, spring, bellow, magnet ball bearing 6010, gasket cardboard ? s 0.3 gost 9347-74, gasket polytetrafluoroethyl ene plate, grade 1 s 2.0, lock washer 10.08?18?10?, lock washer 16.08?18?10?, bolt m10, axle, ball link, end-thrust bearing, bushing, axle, bushing 12x10, shackle, bushing 10x10, cap nut, cross-piece, valve, gasket paronite (p)oh-(b)t s 1.0 gost 481-80, gasket paronite (p)oh-(b)t s 1.0 gost 481-80, lock washer 16.08x18x10t, stud m24, stop valve assembly, stem, valve seat, valve, bellows as an assembly, tail piece, coupling of 2 halves, spring, gasket d 189?153?4, key, key, gasket cardboard ? s 0.3 gost 9347-74, gasket cardboard ? s 0.3 gost 9346-74, gasket paronite a-1 s 1.0 gost 481-80, gasket paronite b-1 s 1.0 gost 481-80, gasket paronite c-1 s 1.0 gost 481-80, lock washer 12. 08?18?10?, lock washer 20. 8?18?10?, lock washer 8. 08?18?10?, spring washer 5 65? 029, spring washer 6 65? 029, stop angle valve dn10 pn 6.4 mpa, lock nut, bolt m12, bolt m10, stud m16, stud m16, stud m20, serrated metal washer, nut m12, nut m10, nut m16, nut m20, special nut, nozzle segment, seal ring - assembl, seal ring - assembl, rear bearing insert, front bearing insert, gland steam regulator assembly, flat spring, membrane assembly, cup, driving half-coupli, ring, driven gear, electric pump shaft, bearing(626)

Central Government / Public Sector

CTN :41224547

18 Aug, 2025 NA

Vijayawada - Andhra Pradesh

Tender For dome casing complete for traction motor cooling blower(mvmt) flat type suitable for 544 m m dia impeller(24 blade design) along with cones jali complete assembly as per bsl drg. no. elw/bsl/wa m4/124-275 or latest if any. note: one sample should be got approved before effecting bulk supply. [ warr anty period: 30 months after the date of delivery ]

Central Government / Public Sector

CTN :41157955

12 Aug, 2025 NA

Kazipet - Telangana

Tender For supply of impeller suitable for traction motor cooling blower (mvmt) 24 blade design as per clw specif ication no. clw/es/b-14/c for wag7 locomotives. [ warranty period: 30 months after the date of delivery ]

Motor Starter Spares Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

Central Government/Public Sector

Central Government / Public Sector

Central Government / Public Sector

Central Government / Public Sector

Central Government / Public Sector