Tender For supply of 47 items of proprietary spares for c650e model bhd machines d d - sm456800012 spring torsion , sm456800020 selector valve , sm456800023 feed pump , sm456800027 grease nipple for track tension , sm456800032 re - air regulator , sm456800052 bush for power lug , sm456800054 check valve , sm456800060 oil seal for head assy. , sm456800063 seal kit for rotary head hydraulic motor , sm456800067 sprocket and bush assy. , sm456800068 gasket oil reservoir , sm456800069 oil seal for head assy. , sm456800072 seal kit - hydraulic cylinder rod slip , sm456800082 pre filter element , sm456800101 gasket , sm456800102 seal kit , sm456800115 coupling full , sm456800125 latch trigger , sm456800293 temperature gauge , sm456800294 temperature sender , sm456800295 pressure regulator , sm456800297 o ring , sm456800299 sealkit , sm456800316 seal kit for pulldown cylinder , sm456800317 seal kit for feed pump , sm456800326 o ring , sm456800328 o ring , sm456800360 seal kit for hydraulic jack cylinder re9 to re14 , sm456800374 seal kit for hydraulic cylinder , sm456800376 re - packing , sm456800377 re - pop safety valve , sm456800380 bushing wear , sm456800381 gasket bottom seal plate , sm456800384 botton head adopter , sm456800388 seal kit for tower raising cylinder re9 to re14 series , sm456800398 head assembly repair kit - part no.g9963 , sm456800402 oil level plug - part no. n7909 for rel , sm456800406 seal kit hydraulic cylinder - rod slip re9 - 14 series , sm456800407 pipe lock re6 to re14 series , sm456800408 oil seal for head assy. rh top seal , sm456800409 oil level plug for rotary head assy.part no. z0804 , sm456800410 hydraulic cylinder for jack re9 to re14 series , sm456800411 hydraulic cylinder - rod slip re9 to re14 series , sm456800412 hydraulic cylinder - mast raising re9 to re14 series , sm456800413 gasket top seal plate for rotary head assembly. , sm456800414 gasket - oil reservoir small , sm456800415 dual over centre valve
Tender For tender for supply of mt sapares d d - hose connection cqa hv 5 31 020 , electro pneumatic valve , head lamp f8043900 , pump hydraulic ram hand driven , clutch cyl repair kit , sleeve cylinder repair kit minor , door lock assy lh , door lock assy rh , poly v belt , pipe intake turbo charger engine non air , propeller shaft bolt , air pressure governor , control valve 9730010200 , water pump , retainer sleeve seal , c a battery inter connector , assy hose , cable assy control , motor engine starter electrical , alternator 60a 28v , dust cover , cover timing belt outside
Tender For providing of repair and overhauling service - repair of drill machine; repair of drill machine; no; buyer premises,repair and overhauling service - repair of hydraulic jack 10 ton; repair of hydraulic jack 10 ton; no; buyer premises,repair and overhauling service - repair of heavy duty digital fast bty charger; repair of heavy duty digital fast bty charger; no; buyer premises,repair and overhauling service - rewinding of heavy duty electric motor; rewinding of heavy duty electric motor; no; buyer premises
Tender For rrsmp/25-26 purnea/02 - repair of road from jalalgarh railway gumti to mahiyarpur via chauhan tola, clearing and grubbing road land (by manual means)clearing and grubbing road land including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300 mm, removal of stumps of such trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, upto a lead of 1000 m including removal and disposal of top organic soil not exceeding 150 mm in thickness as per technical specification clause 201., scarifying existing bituminous surfacescarifying the existing bituminous road surface to a depth of 150 mm and disposal of scarified material with a lift upto 3 m and lead upto 1000 m as per technical specification clause 301.4., construction of subgrade & earthen shoulderconstruction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table 300.2 with lead upto 1000 m as per technical specification clause 303.1., granular sub-base with well graded material (table 400.1)construction of granular sub-base by providing well graded material (crushed stone aggregates and local sand), spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at omc, and compacting with three wheel 80-100 kn static roller capacity to achieve the desired density, complete as per technical specification clause 401, ( by mix in place method ) for grading ii material, wmm(wet mix macadam)providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at omc in mechanical mixer (pug mill), carriage of mixed material by tipper to site, laying in uniform layers in sub-base/base course on a well prepared sub-base and compacting with smooth wheel roller of 80 to 100kn weight to achieve the desired density including lighting, barricading and maintenance of diversion, etc as per tables 400.11 & 400.12 and technical specification clause 406., prime coat (low porosity)providing and applying primer coat with bitumen emulsion (ss-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0kg/sqm using mechanical means as per technical specification clause 502, tack coatproviding and applying tack coat with bitumen emulsion (rs-1) using emulsion distributor at the rate of 0.20 to 0.25 kg per sqm on the prepared bituminous surface cleaned with hydraulic broom as per technical specification clause 503., semi-dense bituminous concreteproviding and laying semi dense bituminous concrete with 100-120 tph batch type hmp producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 4.5 to 5 per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per morth specification clause no. 508 complete in all respects., cement concrete/panel concrete pavementconstruction of un-reinforced, dowel jointed, plain cement concrete pavement over a prepared sub base with approved grade cement @ 400 kg per cum, coarse and fine aggregate conforming to is 383 as per actual design mix, processing 28 days minimum compressive strength of 35 (thirty five) mpa and minimum flexural strength of 4.5 (four point five) mpa, maximum size of coarse aggregate not exceeding 25 mm, mixed in a batching and mixing plant as per approved mix design, transported to site, laid with a fixed form or slip form paver, spread, compacted and finished in a continuous operation including provision of contraction, expansion, constructi
Tender For corrigendum : supply of service and repair job works for tata sumo and maruty gypsy mpfi - hydraulic head , came plate , cross disc , x nozzle , supply pump , support ring , roller , bearing pin , service charges of fuel injection pump , core assy , service charge of turbo charger , crank shaft testing , crank main brg beg end brg grinding and setting , main brg and beg end brg matching and setting , block sleave fitting and boaring and policing , sleave colles facing , c r bush fitting and remvring , block facing , main brg parent bore lline , head facing and testing , head seat fitting cutting and rembring , guide fitting and rembring , valve grinding and lapping , pirton top checking , camshaft alignment , alternator check and repair , starter moter check and repair , radiator flushing and cleaning , crank shaft grinding main and beg end matching m gypsy mpfi , main brg and beg brg matching and setting m gypsy mpfi , block sleave fitting and boaring and honingh m gypsy mpfi , head seat fitting cutting and grinding m gypsy mpfi , valve grinding and lapping fitting and remring m gypsy mpfi , cylinder head surfacing and testing , alternator checking and repairing m gypsy mpfi , self motor checking and repairing m gypsy mpfi