Tender For trans receiver vhf radio 25 watt set for frequency band 146 mhz to 174 mhz full band alongwith suitable antenna, sufficient cable length for connecting antenna complete with connectors, microphone with press to speak switch with coil cord cable, connector for connecting power supply; the equipment must be complied with rdso specification no. rdso/spn/tc/107-2018 ver. 2.0 or latest. specified items as per clause 10 of rdso specification: 10.1 spot-frequency: 146 to 174 mhz (full band), 10.2 required technical parameter as per clause 5.0 (d) - 25 w vhf digital radio set, 10.3 battery type: not to be supplied. 10.4 battery capacity: not to be supplied. 10.5 length of cable to be supplied with each radio: standard length to be supplied is 30 mts. 10.6 requirement of gis software: the set will have built in gps with capability of gis. one number of tuning kit with software to program shall be provided. [ warranty period: 30 months after the date of delivery ]
Tender For supply of electricals goods - 3014131, 200.000, contact jaw for 4000a l&t make air circuit breaker.cn-cs-4000 ho.as per sample.material;copper only.otherwise we will rejected., 3098224, 4.000, energy meters.make; schneider.model no: metseem6436hcl10rs.test parameter : v,i,f&prated current : 5 aaccuracy class : 1.0serial no : 540420298112require for pcc panel in dg section.note ;this type job work with material require by only schneider authorised dealer/service provider only because programming and calibration also require.reference;sarita electrical recomonded because already in plant calibrated by him and also bhawan stp meter installed and calibrated properly also he is scneider authorised service provider only in rewari region.
Tender For supply of marking diagram outside for lhb ac ra coach., as per drawing: ra83115, follow material spec. to rdso specification no. rdso/2006/cg-13 rev-01 option b (ref. md46271 dated 01.04.25), packing instruction: exterior sticker/ marking diagram outside set of sidewall stickers should be rolled firmly on a cardboard tube/pipe of aprox. 03 inches diameter of sufficient strength and length more than sticker 2-3 inches of maximum widthof sticker . endwall stickers of same set should also be rolled on seperate another cardboard tube/pipe (having similar dimensional and strength parameter ) in same way. both tubes of one set should be packed together in a bio degradable transparent polyethylene packing. stickers or any edge of sticker should not be found folded in packing.vinyl film side of stickers should be on the outside of tubes.these individual sets are further to be packed in card box (containing bulk quantity of sets). a list should be pasted on each set of transparent polyethylene packing and also on card box (containingbulk quantity of sets) showing pl no., item description, po no., name and address of supplier, date of manufacturing, lot number, lot quantity, list of items in a set etc. [ warranty period: 12 months after the date of delivery ]
Tender For corrigendum : supply of bogie frame to drg. no. (a) icf/mrvc/d-0-3-001, alt "n", col-ii (or) (b) icf/mrvc/d/bt-0-3-001, alt "c", col -ii along with damper fixing bracket to drg. no. (339)ac/dcemu/d6-0-1-602,col.i - 4 nos andbolt complete to drg. no. emu/m/3ph-0-2-002, alt "c", col.i - 16 sets bogie frame to be supplied without nylon bushes where ever applicable and shall confirm to rdso/specn.c-9202, rev-2 or latest. the firm shall fulfil the requiremnt as per icf/md/specn/147, issue status 01, rev-02 with amendment no- 02. special condition : - suppliers commitment will be there to supply as per drawing -(a) ( for dash pot arrangement ) or as per new drawing - (b) ( for adoption of conical spring ). - one month notice willbe given to vendor whether he has to supply as per drawing - (a) or drawing - (b). -rate quoted will be applicable to both drawing - (a) and drawing - (b) . i) paint scheme shall be as per drawing. ii) qap to format icf/ims/md/f-31 shall be prepared along with relevant documents and kept ready for developmental/educational order. iii)firm should supply bogie frame along with the dimensional report, stress relieving report and radiography films. iv) firm should have induction/electric furnace for stress relieving of bogie frame. v) prototype inspection is applicable only for first time of developmental/educational order. vi) stage inspection to be done as below. (a) raw material stage 1. ensure the raw material used using portable spectrometer machining stage 1. dimensional checks 2. edge preparations (b)welding stage 1. weld parameter to be checked and recorded. (c) surface preparation and painting stage. 1. short/sand blast to the requirements. 2. painting process as per the specification. 3. final product inspection. [ warrantyperiod: 30 months after the date of delivery ]