Tender For corrigendum : supply of 415v, utilization category ac23a, 630a local isolator cabinet in sheet steel enclosure complete with 630a, 3 pole load break switch. 2. shall be with side operated handle, padlocking facility, prebreak micro switch having 1no+1nc contact. 3. micro switch contacts shall be wired to 4 sq mm tb for external termination. 4. provision of padlock system having sufficient space to lock the isolator at off position by minimum two agencies at a time. 5. complete with both power & control circuit wiring with all insulators, bus bars and control terminal blocks. 6. detachable bottom gland plate for entry of cables from bottom. 7. front door shall be hinged and inter-locked with the isolator in 'on' position. the front door should have a minimum 3 mm thickness perspex/triplex window for observation of position of contacts. 8. isolator should confirm to iec 60364 standard. 9. the dimensional drawing of the local isolator cabinet or product catalogue showing mounting arrangement of the components should be enclosed along with the offer. 10. isolator cabinet should be provided with rain canopy. 11. any isolator parts should not be made of aluminium/aluminium alloy. 12. isolator cabinet shall be metal enclosed suitable for wall fixing using 4 welded fixations, dust and vermin proof and shall be provided with degree of protection as ip-55. 13. provision for three distinct parallel busbar per phase for termination of three nos of 240 sqmm aluminum cables for incoming and two distinct busbar per phase for termination of 120 sqmm copper cable. 14. all hardware used in isolator cabinet shall be corrosion resistant. 15. minimum clearance between the live parts and detachable bottom cable gland plate shall be 400mm. 16. cabinet should be painted with alkaline resistant epoxy paint. 17. isolator cabinet shall have provision for earthing at two separate and distinct points. 18. each isolator cabinet should be supplied with panel keys., push button station specification: 1. pbs made of 2mm sheet steel enclosure with rain canopy, protection: ip-65. 2. 01 no. of green colour start pb with 1no+1nc contacts, 01 no. of red colour stop pb with 1no+1nc contacts, 01 no.of increase pb with 1no+1nc contacts <(>&<)> 01 no.of decrease pb with 1no+1nc contacts. one emergency stop push button with 1no+1nc contacts (push to lock type) shall be provided. size of each push button is of 22.5mm diameter. inscription plate for all push buttons. 3. pb shall be wired with 2.5 sq.mm. copper wire to 40 nos. serially numbered terminal blocks (tb) of elmex make having tb-5-6, 7-8, 11-12, 13-14 <(>&<)> 17-18 shorting link. 4. two nos. of cut out of size 72x72 mm for ammeter and rpm meter shall be provided. 5. 'on','off' <(>&<)> 'trip' indication led lamps in red, green <(>&<)> amber colour respectively with inscription plate to be provided. 6. all push buttons, elements, led lamps <(>&<)> cutout for ammeter <(>&<)> rpm meter shall be on the hinged door of the pb station. 7. pb station shall be weather proof, neoprene rubber gasket suitable for outdoor application. 8. 2nos. of earthing studs to be provided. 9. left side hinged door shall be provided with flexible braided copper earthing. 10. pbs shall have 04 nos. of corrosion free bracket suitable to fix on vertical surface. 11. detachable gland plate to be provided. 12. the push button shall be painted with one coat of red oxide primer <(>&<)> two coats of zinc chromate primer and finally finished with stoving enamel grey paint. 13. the push button station shall be generally in line of enclosed drawing (fig-2). 14. party to submit the drawing along with the offer for technical scrutiny.
Tender For supply of interior stickers with braille script for lhb gs coaches., as per drawing: lg6 4005 alt d item no.1,6,11 to 16,18 to 20,22,23,25,27 and 29 with braille script to icf/md/spe c-317, rev.00, packing instruction: lettering inside: one complete set of lettering inside sho uld be packed in cardboard box. different subsets should be made & a list of items sho uld be pasted on each packet of subsets. letters packed in each subset under different headings are as under:- plumbing : emergency flush button, press for flush, notice for bio toilet moulding:- duties of coach attendant, push, pull, no smoking, alarm and pena lty notice, door closes automatically, safety message near gate, notice for luggage c apacity. lavatory:- dust bin, fire extinguisher, soap dispenser, no drinking water, no wa ste into toilet, western style, press for flush, fire prevention and safety, marking of l avatories / body side door, notice for lavatories, drinking water, unified notice for fir e prevention & safety. seat & berth:- sticker for seat number, berth numbers, letter for chaining luggage, notice for unreserved coaches. air brake:- reset emergency brake, f eed pipe, brake pipe, closed, open, hand brake panel : furnish plate, complaint book. wind ow & ceiling: pull window glass inside, indication plate & sticker for emergency windo w, emergency openable window. note : firms have option to provide qr code the cardboard box shall carry a qr code having details as listed below : " name of the man ufacturer " purchase order number " purchase order date " unique serial number (or lot number for bulk items) of the manufacturer or " date of manufacture " delivery challan no. " delivery challan date the qr code shall be as per iso/iec18004 model2 and the data shall be available as xml using the tags detailed above. [ warranty period: 30 months after the date of delivery ]
Tender For supply, storage, installation, commissioning and trial run of electro-mechanical equipment at raw water and clear water pumping station under kanchrapara municipality. - for rwps, supply, delivery , storage, installation, testing & commissioning of vertical turbine type centrifugal pump with cashion pipe ,column assembly, discharge head, sole plate, motor stool and all other accessories all complete of 750m /hr discharge at a head of 29 mtr at duty point as per technical specification . maximum allowable speed of pump shall be 1000 rpm., supply, delivery , storage, installation, testing & commissioning of vertical, scim ,tfec, 110 kw (minimum), 415 v 10% , 50hz 05%, speed 1000 rpm (syn) , to vertical pump duty motor to match with pump at sl no- (1) complete with coupling hub and all other accessories as per specification., supply, delivery , storage and installation at site of ms pipes, specials, joints, flanges as per specification and technical offer. (for both individual pump delivery pipe and extended part of common manifold if required) ., supply, delivery and installation and commissioning of valves complete at site with fixture as per specification and technical offer & as follows :-, di butterfly valve for delivery side of pump fitted with electrical actuator suitable for local and control desk operation and display system for the individual pump delivery pipe line. (350 mm minimum))(pn 16 type), di non-return valve for individual pump delivery pipe line. (350 mm. minimum))(pn 16 type), supply, delivery at site and storage of m.s. dismantling joint assembly for the individual pump delivery pipe line as per specification (350 mm minimum)., supply, delivery ,storage and installation at site of pressure gauges complete with fittings and fixture as per specification, pressure gauge for delivery side (0 10 kg / cm2), supply, delivery ,storage and installation at site of pressure transmitter complete with fitting and fixture as per specification as follows:-, pressure transmitter for delivery side ( 0 10 kg / cm2 ), supply, delivery at site and installation of m.s. structural materials for cable tray / rack, panel installation supports, pipes & valves supports, fabricated stairs & all other fabrication work., lt panel, modification / retrofitting/expansion/addition of the existing pmcc with supply , delivery & installation of a new additional motor starter feeder at rwph in order to accomodate the extra pump-motor feeder of requisite rating not less than 110 kw .the modification/addition should match/synchonise the existing panel and should ensure smooth operation of the complete panel as a single entity and should be fit to install at the existing pump house., retrofitting of existing control desk at site with supply,wiring, installation of additional items like temparature scanner , multifunction meter , microprocessor based position indicator, digital pressure indicator,tnc switch, push button switch, indication lamps etc .as required to complete for the new pump motor set., supply ,delivery, laying, installation of power cable of adequate size from motor feeder to motor .(min. 2 run x 3core , 185 sq mm xlpe armoured al. for each feeder), supply ,delivery, laying, installation of power cable of adequate size and length from pmcc to motor space heater . (min. 3 core 2.5sq mm. armoured cu for each motor), supply ,delivery, laying, installation of power cable of adequate size and length from pmcc to valve actuator etc. elsewhere required. (min . 4 core 2.5 sq mm. armoured cu), making end termination of all the power cables as stated in sl no 11,12,13 with all necessary equipments like termination kits(dry type), lugs , glands etc , installed for the modification job., supply ,delivery, laying, installation of control cables of different size as required for the purpose and length for completing the different control connections between control desk, motor feeders , lpbs, pmcc etc.to the satisfaction o
Tender For corrigendum : supply of item name:- vcb trolley make - cg power and industrial solutions limited (mv switchgear division) panel type - jvac rated voltage - 11000 v, mechanism: trip-free, breaking capacity - 25 ka @ 11 kv, short time rating(str) - 25 ka for 3 sec, ct primary current - 800 amp., bus-bar current - 1250 amp., mechanism - motor operated spring charged, closing coil - 110 v dc, indication circuit - 110 v dc, trippin g coil - 110 v dc, panel space heater - 230 v ac, spring charge motor - 230 v ac, frequency - 50 hz, draw ing no.: vs9260-z-21, w/o no. - v9260,make-cg power and industrial solutions limited (mv switchgear div ision) [ warranty period: 30 months after the date of delivery ]
Tender For corrigendum : supply of spares of electrical panel accessories for csctpp, chhabra - led indication lamp sr. no. a1 to a6 , led indication lamp sr. no. a7 to a10 , led indication lamp sr. no. a11 to a15 , led indication lamp sr. no. a16 to a18 , flush type push button sr. no. c3 to c5 , push button with led indicating lamp sr. no. c6 & c7 , emergency stop push button sr. no. c8
Tender For supply of lt distribution panel with 4 nos. suitable capacity & size copper bus- bar arrangeme nt consisting of 2 nos. 4pole 400a mccb for incoming and 1 no. 4 pole 250a mccb, 1 no. 4 pole 160a mccb, 1no. 4 pole 125a mccb and 2 nos. 4 pole 63a mcb for outgoing along with complete wiring, indication lamp, metering arrangement and all accessories as per pcee/cege/ser specification no. ser/elec/gs/descriptio n/lt panel/1/rev-0/mar 2024 dimension -hxwxd -1500 mm x 1800 mm x 700 mm. [ warranty period: 3 0 months after the date of delivery ]