Tender For supply of spares for bottom ash handling system of ash plant - unit no.3, 4 & 5 at gandhinagar tps. - shoulder bolt with lock plate for assembling part no.8 (part no.9) for 24" x 24" feed gate assembly of bottom ash system unit- 3 and 4 as per dwg. no. 8743-2b-571., cross brace (part no.11) for 24" x 24" feed gate assembly of bottom ash system unit- 3 and 4 as per dwg. no. 8743-2b-571., resilient gate face p.no-2,for bottom ash hopper,drg 8743/2b/571, shoulder bolt with lock plate for assemblying part no.8 (part no.9) of 24x24 squire bottom feed gate dwg.no. 95p10-t-2b-570 of unit no. 5, cross brace (part no.11) of 24x24 squire bottom feed gate dwg.no. 95p10-t-2b-570 of unit no. 5, gate face 1 set consists of ss:316 gate face with m.s back up plate of 24x24 squire bottom feed gate of unit no. 5, cam segment p.no-1 for 33"x30 excen crusher, front wear plate/anvil plate of 33" x 30" clinker crusher / grinder assembly for unit-3and4 (1 set equals to 3 nos.)., back wear plate/plate combing (part no. 6) of 33" x 30" clinker crusher / grinder assembly as per dwg. no. 8743-2b-582(rev-1) for unit-3 and 4 (1 set equals to 3 nos.)., side wear plate(part no. 8) of 33" x 30" clinker crusher / grinder assembly as per dwg. no. 8743-2b-582(rev-1) for unit-3 and 4 (1 set equals to 2 nos. left hand and 2 nos. right hand wear plate)., shaft with shaft structure and shaft sleeve of 33" x 30" clinker crusher / grinder assembly for unit-3 and 4., 33"x30" single roll clinker crusher / grinder complete assembly without drive arrangement, fluid coupling, chain drive and driven sprocket as per dwg. no.8743-2b-582(rev-1) for unit-3and4, feedsump below clinker crusher for unit no.3 and 4, roll (cam segment) 1 setequals to 8 nos. cam segment of single roll crusher for unit no. 5, front wear plate/anvil plate (part no.3) 1 set consists of 3 nos b front wear plate of single roll crusher dwg.no.95p10-2b-582 (rev-1) for unit no. 5, back wear plate/plate combing (part no.6) 1 set consists of 3 nos back wear plate of single roll crusher dwg.no.95p10-2b-582 (rev-1) for unit no. 5, side wear plate (part no.8) 1 set consists of 2 nos. left hand and 2 nos right hand type of single roll crusher dwg.no.95p10-2b-582 (rev-1) for unit no. 5, shaft with shaft structure with shaft sleeve(part no.2 and15)for clinker grinder., bearing support (part no.8) of single roll crusher dwg.no.95p10-2b-582 (rev-1) for unit no. 5, single roll crusher complete assembly without drive arrangement,fluid coupling,chain,drive and driven sprocket of single roll crusher dwg.no.95p10-2b-582 (rev-1) for unit no. 5, feed sump of bottom ash system of unit - 5 as per drawing no. 95p10 - t - 1b - 711, complete assembly of feed gate housing with feedgate, access door for unit no.3 and 4, bearing housing of dcips make 33" x 30" clinker crusher/grinder, locking plate for 600 dia. round access door for bottom ash hopper, nozzle with ceramic tip(part no. 2)tip size- 36 mm of 8" jet pulsion pump assembly for bottom ash system of unit-3 and 4 as per dwg.no.8743 - 2b - 591(rev-1), aligning ring(part no. 10)of 8" jet pulsion pump assembly for bottom ash system of unit-3 and 4 as per dwg.no.8743 - 2b - 591(rev-1), half clamp(part no. 11)of 8" jet pulsion pump assembly for bottom ash system of unit-3 and 4 as per dwg.no.8743 - 2b - 591(rev-1) 1 set equals to 2 nos., 9" flange clamp half (part no. 18) of 8" jet pulsion pump assembly for bottom ash system of unit-3 and 4 as per dwg.no.8743 - 2b - 591(rev-1) 1 set equals to 2 nos., 8" jet pulsion pump complete assembly without tail pipe for bottom ash system of unit-3 and 4 as per dwg.no.8743 - 2b - 591(rev-1), nozzle with ceramic tip size 34 mm of jet pump for b.a system dwg.no. 95p10-2b-591 (rev-1) for unit no. 5, aligning ring (part no.10) of jet pump for b.a system dwg.no. 95p10-2b-591 (rev-1) for unit no. 5, half clamp (part no.11) 1 setequals to 2 nos of jet pump for b.a system dwg.no. 95p10-2b-591 (rev-1) for unit no. 5, 9" flange clamp half (part no
04 Aug, 2025
67.93 Lacs
