Latest portable generators scrap Tenders | Government portable generators scrap Tenders

Central Government And Public Sector

CTN :38587336

28 Dec, 2024 8.22 Lacs

Mumbai - Maharashtra

Tender For customized annual maintenance contract (amc) / comprehensive maintenance contract (cmc) for pre-owned products - amc; zeiss; annual maintenance contract (amc); quarterly; no; 1. routine maintenance, performance checks, re-alignment, repair and replacement of defective components and parts-hv cable assembly, ex mva "x" part-no.: 311311 -orsay , ex mva "y", valve assembly, spare assembly, o-ring iso valve, electro valve, 20 kv high voltage module, leader card holder, pneumatic actuator set, apertures assembly, o-ring for nozzles block, o-ring for aperture drive, steppermotor driver 51xpack2 /trinamic, gis psu, actuation cylinder complete, connector, nozzle head complete, high voltage module, grounding module f/liner tube lens, floater 300v, 0,5a 3/4", ex eht digit. controlled tetrode supply, xb scan piggy board, scan-generator, complete (auriga), e/o board hw4.0(3.5) with fw3.1.0, ex vac.-control board leo 15xx "stan dar, interlock piggy (mod. version), needle valve piggy with mounting parts, vac relay pcb (1400), main psu, fib-electronic pcb complete, deflector amplifier, internal generator, 6 hole aperture, pre-aperture 3h6x0,25/ 0,110mm, anode screw din 7984 m4x6 e, helicoflex-hnv-120-19,7-23,7-2-alu a5, copper gasket, spring+spool f/y axis assy, power supply tpsll0 /pfeiffer vacuum, compact fullrange gauge pkr 251, scintillator assembly, mikro-magnetventil 24 vdc, control pcb water chiller, ion pump, 30l/s noble pump, exhaust, ion pump kit (ion pump+dn35cf) -orsay , ion pump psu(neg) to 910846 1p100/702/02, tip seal kit for nxdsloi pump, illumination assy infrared,compl., spanner wrench, scintillator-changer, pcba 3-channel controller w/rs232, vp holder for 6 hole aperture l00na, extractor - aperture, denka kathode tfe 174c, transmitter extractor voltage, vat civ valve upgrade kit ose au/u/vp, servicepackage hipace 300 plus ose, se-multiplier, complete, pcba 3-channel controller w/rs232, ads 3 jsr m/s repair-kit, membrane f. isol-use# 348201-8902-910, motor assy, step, uhv,sd,1.0a, y-motor assy,step,uhv,sd,1.8a, r motor assembly pllo motor, vac relay pcb (1400), x-spring assembly spool + spring, install.kit for opt. sensor (le-geu-017), on/off-switch complete with pcb, airlock window, pcb for water chiller, asb-detector diode at objective lens, zylinderschraube 2 din912-m4x6, longetterpump 20l, copper sealer dn 40 cf cu pf501404-t, ex fib hv cable assy -orsay , 90u anode aperture, unloader valve for jun air compressor, chiller water pump, van der heijden, water chiller air cooled type, 12v 42ah smf battery for lokva ups, gallium source, gallium source refilled, liner tube assy, fib aperture set 50u,20u,50u,100u,200u,400u, copper gasket for gallium emitter, compressor pi-120-25, 230/50-60hz, dry backing pump system nxdsl0i, set anode screws m4x6 din7984 8x, reservoir pt, cable for penning (new pfeiffer), ex controller f/steerer, ex pcba stage controller, joy stick, controller -2. to keep the equipment in up to-date condition during the period of the contract.-msme exemption - no | startup exemption - no,

CTN :38074379

04 Jan, 2025 NA

Visakhapatnam - Andhra Pradesh

Tender For corrigendum : tender for supply of phase sequence indicator , rotating rectifier assembly , generator control unit type iver 2nm , automatic voltage regulator , kvr-2 , rotating rectifier assembly for 350kw , 500kw alternator , automatic voltage regulator , kvar-4 , automatic voltage regulator type ievr 2n , regulator avr ievr-2 industrial electronic voltage , bearing nde-6310 , wound stator with free leads , auto manual switch 10a , 240v , 1 pole , automatic voltage regulator-ievr2n , hrc fuse links-415v ac , 6a ns 6 , hrc fuse links-415v ac , 2a ns 2 , rotating rectifier assembly , bearing de side for motor -6310c3

CTN :37686863

31 Jan, 2025 NA

Delhi - Delhi

Tender For corrigendum : procurement of spares for mig-29 upg aircraft - transistor, microcircuit, linear (voltage regulator), integrated circuit, signal generator im 511001, mtsp-18, high frequency flow-control valve, a6 pcb

Central Government/Public Sector

CTN :38589103

03 Jan, 2025 NA

Chennai - Tamil Nadu

Tender For supply of speed control of converter fed dc motor setup,speed control of chopper-fed dc motor setup,dsp-based speed control of srm motor setup,ac voltage controller-based speed control of induction motor setup,vf control of three phase induction motor setup,microcontroller-based speed control of stepper motor setup,speed control of bldc motor setup,voltage regulation of three-phase synchronous generator setup

CTN :38519115

20 Dec, 2024 NA

Netanar - Chhattisgarh

Tender For supply of ims gauge spares at nmdc steel limited - ims gauge 15039 relay rel mr 24dc 21au m , ims gauge 14920 displacement transducer , ims gauge 59823 filter ir cut m55x0,75 , ims gauge 13992 solenoid valve mfh 3 1 8 , ims gauge 57898 cleaning tissue safepad , ims gauge 10331 bluesil paste b 431 , ims gauge 50858 signal lamp, 4 fold led , ims gauge 13713 toothed belt, 10 t 5 610 , ims gauge 63811 encoder system ethercat, , ims gauge 43519 high voltage unit tibn 2 , ims gauge 36956 lens s componon, 4,0 80 , ims gauge 38089 filter 450nm 50mm 450fs8 , ims gauge 29218 lens cinegon, 1,4 8, c m , ims gauge 28618 lamp osram hmi 1200w gs , ims gauge 61900 high voltage generator w , ims gauge 44229 ad converter 8k tica 104 , ims gauge 49316 canopen function module

Central Government/Public Sector

CTN :38041097

21 Dec, 2024 NA

West Tripura - Tripura

Tender For corrigendum : custom bid for services - repair and maintenance of ac modules dc modules and various pcbs of all departmental drilling rigs of ongc tripura asset-work includes but not limited to supply of men, materials, testing equipment / tools etc for fault finding (trouble shooting), repairing, calibration and functional testing of ac modules, dc modules and various pcbs in e1400 series drilling rigs of tripura asset. broad details of the activities to be carried out are as below: a. following jobs are to be carried out in pcbs i. physical checking of healthiness of components & cleaning of the pcbs. ii. checking of voltages at different points in the pcbs after powered up through simulator. iii. replacement of faulty components, limited to 50% cost of the pcb, to make it operational. iv. calibration of pcbs v. on load testing of 12 hrs. continuous loading for satisfactory operational vi. fixing of pcbs in the respective panels b. following jobs are to be carried out in ac module i. visual inspection of module for any loose hardware & cleaning of the module. ii. checking of circuit by using simulator. iii. checking of over frequency tripping. iv. checking of under frequency level. v. under frequency voltage cut back test vi. idle-run ramp and idle trip test vii. throttle regulation check viii. master slave and command circuits check ix. current demodulator check x. automatic voltage regulator check xi. meter circuit check xii. over voltage trip check xiii. reverse power trip check xiv. frequency demodulator check xv. module panel meter check xvi. replacement of faulty components, limited to 50% cost of the ac module, to make it operational. xvii. on load testing of 12 hrs. continuous loading for satisfactory operational xviii. fixing of ac modules in the generator panel c. following jobs are to be carried out in dc-module i. visual inspection of module for any loose hardware & cleaning of the module. ii. dead band and current limit calibrations iii. zero throttle interlock circuit test iv. firing circuit test v. speed feedback circuit test vi. power limit circuit test vii. slave circuit test viii. manual voltage circuit test ix. over current trip calibration test x. meter circuit check xi. replacement of faulty components, limited to 50% cost of the dc module, to make it operational. xii. on load testing of 12 hrs. continuous loading for satisfactory operational xiii. fixing of dc modules in the dcpcr panel d. following jobs are to be carried out in battery charger i. visual inspection and cleaning of components such as transformer, voltmeter, ammeter, pcbs, rectifier, indication lamps and tightening of loose hardware, if any. ii. checking of tripping logics, dc under voltage, dc over voltage, reverse polarity, ac mains fail, over current, over temperature etc. iii. replacement of faulty components, limited to 50% cost of the battery charger, to make it operational.-msme exemption - no | startup exemption - no

State Government

CTN :38507691

09 Dec, 2024 40.00 Lacs

Multi City - Bihar

Tender For supply of machines and laboratory equipment?s for electronics engineering - 8051 microcontroller trainer , lcd 16x4 alphanumeric display , 4x4 matrix deypad , dac0808 8-bit digital to analog d/a convert ic package dip-16 , ic-741 , adc0808/0809 , stepper motor , dc motor , at89s52-24pi / at89s52 ic atmel 8051 microcontroller 40 pin dip mount chip 8 bit microprocessor 8kb isp(in system programming) flash memory up to 33mhz clock frequency speed , digital communication training system , advance digital communication training system , 10 khz to 3 ghz spectrum analyser with tracking generator , 100 mhz dual channel digital storage oscilloscope , a) verify the open loop transfer characteristics of op-amp using ic-741. also determine gain of b) inverting, c) non-inverting and d) buffer amplifier using ic-741 on bread board and triner kit , design wein bridge osccillator using ic-741 on bread board and determine the frequency of oscillation. wein bridge osccillator using ic-741 , design square wave generator using ic-741 and calculate the duty cycle of the generated waveform. square wave generator using ic-741 , design an astable multivibrator using ic-555 timer and calculate the duty cycle and pulse with of the generated wave form. , design an monostable multivibrator using ic-555 timer and calculate the cycle and pulse witdth of the generated waveform , design a 2nd order active low pass, high-pass, band pass and band-reject filter using ic-741 op-amp on breadboard and trainer kit , calculate the lock range and capture range of pll using ic-565 , construct sample and hold circuit using ic-741 on bread board , kelvins double bridge test kit , wheatstone bridge test kit , d.c. potentiometer kit with 12v (d.c.) standard cell , temperature transducer kit , transformer oil dielectric strength testing kit upto 30kv , ammeter 0-5a and 0-10a - voltmeter 0-300v and 0-600v , 1-$ and 3-$ energymeter testing kit , rheostats of various ranges , digital multimeter , analog multimeter , wattmeter (0-75w), (0-150w) and (-350w) , meggar , microprocessor kit (8085 based) , trainer board of junction diode , logic gate trainer board , cro 30mhz dual trace , d/t flip-flop , common emitter transistor set , analog to digital converter interface card , 4 digit seven segment display interface card , dac kit , 8086 microprocessor trainer kit for study , intel 8051 microcontroller kit with data card , a/d converters experimental kit (adc 0800 series) , led display kit with card , lcd display kit with card , interface cards for stepper motor & dc motor control , construct the circuit and plot the , characteristics of the pn junction diode, find the cut in voltage objective : to study forward & reserve characteristics of pn juncton diode. , construct the circuit and plot the characteristics of a zener diode. find the breakdown voltage objective: to study forward & reverse v-i characteristics of zener diode. , objective: to study forward & reverse characteristics of pn junction diode , construct the circuit and plot the , characteristics of the pn junction diode, find the cut in voltage objective : to study forward & reserve characteristics of pn juncton diode. , construct the circuit and plot the characteristics of a zener diode. find the breakdown voltage objective: to study forward & reverse v-i characteristics of zener diode. , objective: to study forward & reverse characteristics of pn junction diode , construct a full wave rectifier and obtain regulation characteristics without filters and with filters. compare the results objective: to study efficiency & ripple factor of full wave & bridge rectifier on application 1 of load & filters. , construct a bridge rectifier and obtain regulation characteristics - without filters and with filters , obtain the charactersics of diac and triac , simulate half wave, full wave and bridge rectifier using simulation tool like pspice/orcad/multisim. , develop circuits simulation mod

Central Government And Public Sector

CTN :38299726

20 Dec, 2024 NA

Nagpur - Maharashtra

Tender For goods, supply, installation, and commissioning of a microcontroller-based electronic speed indicating and recording system for track machines. the system to comply with rdso specification no. mp.0.3700.07, rev-7, august 2017, and includes flash memory storage of up to 90 days (internal memory ). specifications include a speed range of 0-120 kmph and an operating voltage of 24 vdc. each set inclu des the items listed below, ( rdso specification no. mp.0.3700-07). 1) recording cum indicator unit (rci)- 01 no. 2) speed indicator -01 no. 3) speed sensor/pulse generator-01 no. 4) junction box with adopter pla te-01 no. 5) connecting cable-01 set of 04 nos.(rci to ind cable length 35 meters) 6) mounting accessori es as per requirement make: laxven systems, medha servo drive, autometers alliance or other rdso ap proved vendors. warranty: as per irs condition of contract. note: the installation & commissioning of the complete set has to be executed at site of working of track machines within secr jurisdiction. [ warranty period: 30 months after the date of delivery ]

Central Government/Public Sector

CTN :38415786

30 Dec, 2024 NA

Itarsi - Madhya Pradesh

Tender For supply of micro controller based electronic speed indicating & recording system for 4 wheeler tower ca r to rdso specification no. m.p.0.3700-07(rev-07) august 2017. scale range 0 to 120 kmph, voltage 24v d c, set consisting of following items, 1) recording cum indicator unit -01 no., 2) speed indicator unit - 01 no. , 3) pulse generator 01 no., 3) junction box-01 no., 4) connecting cables-01 set of 05 nos. (recorder to indic ator communication cable 35 mtrs.), 5) mounting accessories-01 set make-laxven/medha/aal or similar. [ warranty period: 30 months after the date of delivery ]

Central Government/Public Sector

CTN :38401373

23 Dec, 2024 NA

Multi City - Multi State

Tender For supply of radiator motor , for lhb type power car, 3 phase squirrel cage induction motor of 30hp/ 22kw, voltage 415v +/-10%, frequncy: 50hz, rpm-1460, ip-55, ambient:50 degree celsius, pf:>/=0.8, efficiency:>/=89.9%, insulation class- f, suitable for radiator of 500kva diesel generator set of cummins, greaves & koel make engines of lhb power cars, as per rdso specification no. rdso/pe/spec /ac/0084-2008(rev-1) with terminal connection, suitable for star delta starter. similar to abb make model no : m2bax180mlb4 imb3im1001.

Portable Generators Scrap Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

Central Government And Public Sector

Central Government/Public Sector

Central Government/Public Sector

State Government

Central Government And Public Sector

Central Government/Public Sector

Central Government/Public Sector