Tender For corrigendum : : supply, installation, testing & commissioning of electrical equipment for dg block 119a of inrp - ht panels (119a)supply, installation, testing & commissioning of indoor type floor mounted, single front, metal clad, 1250 a, 6.6 kv, 3 phase, 3 wire, vcb switchgear panel suitable for a short circuit current of 31.5 ka for 3 seconds, internally arc tested for 31.5 ka for 1 second, comprising of following incoming & outgoing feeders : incoming feeder: 1 no. 1250 a, 3p vcb outgoing feeders: i) 7 nos. 630 a, 3p vcbii) 1 no. 1250 a, 3p vcb as tie feederwith surge arrestors, relays, pts, cts & other necessary accessories including associated structural steel required for complete installation of the panel & equipment earthing of the panel from both the earthing terminals of the panel to the nearest earthing grid conductor existing at site using copper conductors of size as per tender technical specifications & drawings. reference drg. nos: ip1/119a/05027339/dwg/001/r0 & ip1/119a/05027339/dwg/002/r0(note: terminal box of each incomer of 6.6kv switchboard shall be suitable for terminating 4x3cx400 sq.mm., 6.35/11kv (e), a2xwy cables.), supply of spares for ht panels as per attached spares list mentiond in section c, part ii of tender, 2.5 mva, 6.6/0.433 kv dry type transformers (119a)supply, installation, testing & commissioning of 6.6/0.433 kv, 2.5 mva, dyn11 dry type cast resin transformer having percentage impedance of 8.5% complete with ht cable end box, lt bus duct flange, off load tap changer on ht side with range of +/-5% in steps of 2.5%, wti scanner, ct for restricted earth fault protection and other necessary accessories including associated structural steel required for complete installation of the transformer & equipment & neutral earthing of the transformer from both the earthing terminals of the transformer to the nearest earthing grid conductor existing at site using copper conductors of size as per tender technical specifications & drawings.reference drg. no. : ip1/119a/05034347/dwg/001/r0, supply of spares for dry type transformers as per attached spares list mentiond in section c, part ii of tender, 2000 kva diesel generator sets (119a)supply, installation, testing & commissioning of 3 phase 2000 kva prime power 433v, 50hz, 0.8 p.f. diesel-generator sets with 110% overload capacity for 1 hr with four (4) stroke inline or vee type cylinder arrangement having engine speed 1500 rpm, 24v electric battery starting system with a provision of interchangeability of battery bank between two dg sets, complete with all auxiliary equipment including amf control panel, auxiliary mcc panels, heat exchanger cooling system, raw water pump, remote radiator with fans on terrace, ms exhaust piping, exhaust structure (maximum 30 m stack), 4 nos. of 3.6 cubic metre fuel day tank outside dg building (for all 4 dg sets) & 1 no. of 990 ltr intermittent tank inside each dg room, ms "c" class fuel piping between engine & fuel tank, dg room accoustic treatment & complete ventilation of dg room, brushless excitation for alternator, one no. 3200 amp 415 v 4p acb, ms structural steel supports/ channels/ angles & other necessary accessories including associated structural steel required for complete installation of the dg & equipment & neutral earthing of the dg from both the earthing terminals of the dg to the nearest earthing grid conductor existing at site using copper conductors of size as per tender technical specifications & necessary statutory clearances from cpcb etc. as required and as per tender technical specifications & drawings. design and construction of foundation for exhaust pipe rack/ structure of dg set is included in the scope of the contractor.reference drg. nos. : i) ip1/119a/05034347/dwg/001/r0ii) ip1/119a/05044831/dwg/003/r0iii) ip1/119a/05044831/dwg/004/r0iv) ip1/119a/05044831/dwg/005/r0v) ip1/119a/05044831/dwg/006/r0, supply of sp
Tender For supply of electrical general items tacho generator 70 ma / 200 v @ 4000 rpm, model: dgt 4000 make: ador powertron , feed back card (for esp transformer 120k/600ma) comp. side 5001-0002-08-41/04 make: adore powertron , frp rod size: length 1050mm, dia. 50.8 mm , motor 7.5hp/5.5kw, duty s1, 4pole, voltage 415v, ip 55, hz 50, amb50 deg c, mounting foot, make bbl/cg, insulation, class f, ie3 , motor 5hp/3.7kw, duty s1, 4pole, voltage 415v, ip 55, hz 50, amb50 deg c, mounting foot, make bbl/cg, insulation, class f, ie3 , heavy duty switch disconnector fuse unit, tpn rating 250 amp. suitable for din fuse-link, make siemens , heavy duty switch disconnector fuse unit, tpn rating 125 amp. suitable for din fuse-link, with ss incloser big size make siemens , mccb 250 a 3pole , 415v, 36ka, xt3n 250 make abb , mccb 160 a 3pole , 415v 50ka, make abb , motor circuit breaker rating 10a type: gv2me14, term/mag 6-10 a rocker make: schneider electric , power contactor 3pole, make siemens coil voltage 230v ac 50hz , 3tf32 with 1no , 3tf33 with 1no , 3tf34 with 1no , power contactor 3pole, make abb coil voltage 110v ac 50hz , a40, 40amp. with 1nc , a30, 30amp. with 1nc , a63, 63amp. with 1nc , power contactor 3pole, make abb coil voltage 230v ac 50hz , a40, 40amp. with 1nc , a30, 30amp. with 1nc , a63, 63amp. with 1nc , power contactor 3pole, make abb coil voltage 230v ac 50hz , ax80, 80amp. with 2no+2nc , ax90, 90amp. with 2no+2nc , power contactor 3poler, make siemens coil voltage 110v dc , 3tf47 with 2no+2nc , power contactor 3pole coil voltage 110v ac, type: a185-30, make : abb with 2no+2nc aux. contact , power contactor 3pole coil voltage 230v ac, type: a185-30, make : abb with 2no+2nc aux. contact , power contactor kit for abb make contactor, a185-30, , power contactor kit for abb make contactor, a145-30, , mcb schneider/abb make, 10 ka, , 63 a, 4 pole , 63 a, 3 pole , 63 a, 2 pole , 32 a, 4 pole , 32 a, 3 pole , 16 a, 3 pole , 32 a, 2 pole , 25 a, 1 pole , 16 a, 1 pole , 6 a, 1 pole , 63a, 4pole, 10 ka mcb, make: legrand/schneider/abb , with 1no+nc aux. contact , rccb, make schneider/abb , 63 a, 30ma, 230vac, 2 pole , 32 a, 30ma, 230vac, 2 pole , 4 change over relay contact rating 3a. coil voyage 230 v 50hz, with base, make schneider/abb , 4 change over relay contact rating 3a. coil voyage 24 vdc , with base, make schneider/abb , overload relay, make l & t, range: , 30-50 (mn5) , 20-32 (mn2) , overload relay, make siemens, range: , 32-50 a (3ua58) , 20-32 a (3ua58) , 17-25 a , abb make overload relay 36-52a , timer s/d make selec, 800sd coil voltage 230v ac, 50hz , on delay timer range: 0-60 sec/min/hrs aux. 230v ac, make: omron din rail type , smps input 230v ac 50hz, output 24v dc 10amp, din rail mount type make shavison/omron , terminal block, make connectwell/ wago/elmax , 2.5 mm2 , 6 mm2 , 16 mm2 , terminal block (busbar type power/nut bolt type), make connectwell/ wago/elmax , 25mm2 , 35mm2 , 95mm2 , 50mm2 , heavy duty copper lug (ring type) make dowells/havells/jaycee, size: , 4mm2 , 6 mm2 , 10 mm2 , 16 mm2 , 50 mm2 , heavy duty copper thimble long barrel make dowells/havells, size: , 16 mm2 , 95 mm2 , 120 mm2 , heavy duty copper lug pin type long barrel make dowells/havells/jaycee, size: , 1.5 mm2 , 2.5 mm2 , 4 mm2 , 6 mm2 , 16 mm2 , heavy duty aluminium thimble long barrel, make dowells/havells/jaycee, size: , 16 mm2 , 25 mm2 , 35 mm2 , 50 mm2 , 70 mm2 , 95 mm2 , 120 mm2 , 150 mm2 , 185 mm2 , 300 mm2 , 400 mm2 , heavy duty copper thimble l shape, make dowells/havells/jaycee size: , 35mm2 , 50 mm2 , 70 mm2 , 95 mm2 , 120 mm2 , heavy duty copper ferrule, make dowells/havells/jaycee, size: , 16mm2 , 25 mm2 , 35 mm2 , 50 mm , 70 mm2 , heavy duty copper lug (ring type) size: 10mm2 od 22mm, id 10mm lump-sum , heavy duty copper lug (ring type) size: 16mm2 od 22mm, id 10mm lump-sum , heavy duty copper lug (ring type) size: 25mm2 od 22mm, id 10mm lump-sum , heavy duty copper lug (ring type) size: 35mm2 od 22mm, id 10mm lump-sum , heavy
Tender For corrigendum : supply of electrical spares c c > f> f - master trip relay , side cable box , power converter 110v ac to 110v dc , digital protection relay , epoxy resin cast current transformer
Tender For corrigendum : providing of repair, maintenance, and installation of plant/ systems/equipments (version 2) - commercial; electrical system or installation; work of vcb repairing & maintenance & powertransformer oil likege maintenance
Tender For corrigendum : providing of repair, maintenance, and installation of plant/ systems/equipments (version 2) - commercial; electrical system or installation; work of vcb repairing & maintenance & powertransformer oil likege maintenance under edd-mahoba
Tender For auction sale of mixed iron scrap,transformer meter box metallic scrap,11/12 kv vcb kiosk (incomplete) scrap,single phase meter static/ pushfit type burnt (e-waste),3.15 mva powertransformer (scrap) copper wound,250 kva 3 phase al. wound dt (scrap),63 kva 3 phase al. wound dt (scrap),25 kva 3 phase al. wound dt (scrap),5 kva 1 phase copper wound dt (scrap),63 kva 3 phase dt mic failed without winding (scrap),40 kva 3 phase dt mic failed without winding (scrap),63 kva 3 phase uneconomical dt lt winding al. wound due to coil weight (scrap)
Tender For auction sale of 250 kva 3 phase copper wound dt (scrap),1.6 mva powertransformer (scrap),250 kva 3 phase al. wound dt (scrap),160 kva 3 phase al. wound dt (scrap),100 kva 3 phase al. wound dt (scrap),63 kva 3 phase al. wound dt (scrap),40 kva 3 phase al. wound dt (scrap),25 kva 3 phase al. wound dt (scrap),16 kva 3 phase copper wound dt (scrap),16 kva 3 phase al. wound dt (scrap),10 kva 3 phase copper wound dt (scrap),10 kva 3 phase al. wound dt (scrap),25 kva 1 phase copper wound dt (scrap),25 kva 1 phase al. wound dt (scrap),16 kva 1 phase copper wound dt (scrap),16 kva 1 phase al. wound dt (scrap),10 kva 1 phase copper wound dt (scrap),10 kva 1 phase al. wound dt (scrap),5 kva 1 phase al. wound dt (scrap),5 kva 1 phase uneconomical dt without winding (scrap),25 kva 1 phase uneconomical dt without winding (scrap),16 kva 1 phase uneconomical dt without winding (scrap),10 kva 1 phase uneconomical dt without winding (scrap),250 kva 3 phase al. wound uneconomical dt (scrap),40 kva 3 phase al. wound uneconomical dt (scrap),16 kva 3 phase al. wound uneconomical dt (scrap),250 kva 3 phase al. wound dt mic failed (scrap) (al. wound) (without winding),100 kva 3 phase dt mic failed without winding (scrap),63 kva 3 phase dt mic failed without winding (scrap),40 kva 3 phase dt mic failed without winding (scrap),25 kva 3 phase dt mic failed without winding (scrap),16 kva 3 phase dt mic failed without winding (scrap),10 kva 3 phase dt mic failed without winding (scrap),10 kva 3 phase al. wound dt mic failed with lt winding (scrap),100 kva 3 phase uneconomical dt lt winding al. wound due to coil weight (scrap),63 kva 3 phase uneconomical dt lt winding al. wound due to coil weight (scrap),40 kva 3 phase uneconomical dt lt winding al. wound due to coil weight (scrap),25 kva 3 phase uneconomical dt lt winding al. wound due to coil weight (scrap),16 kva 3 phase uneconomical dt lt winding al. wound due to coil weight (scrap),10 kva 3 phase uneconomical dt lt winding al. wound due to coil weight (scrap)