Latest propeller shaft assembly Tenders | Government propeller shaft assembly Tenders

State Government

CTN :43467490

13 Jan, 2026 NA

Delhi - Delhi

Tender For s/i/t/c of e/m equipments and allied works for newly re-bored tube well at okhla vihar near majar in okhla constituency ac-54. - supply of submersible pump set fitted with dynamically balanced ss impeller mounted on stainless steel shaft with protection sleeve having stage bowl & closed grained shorted type impeller, the pump will be directly coupled to required wet type induction motor of 7.5 hp, 15 stage, speed 2900 rpm suitable for operation of 3 phase, 415 volt, 50 hz, ac supply with efficiency 70% at following duty point: 200-125-75 lpm on 89-124-133 mtr. head.having discharge outlet 50 mm and outside dia 142 mm.make: bs/skope/ any djb approved. , supply of hut type electrical feeder pillar / fabricated with 50 x 50 x 6mm angle iron and 16 swg ms sheet with horizontal and vertical intermediate member of suitable size. i.e. 1370 mm x 760mm x 460 mm. with arrangement for mounting of switchgear and electrical energy meter i.c. painting heaving following item fitted. a) mccb 63 amp, 4pole, 415volt, 35 ka -1 no. b) rccb 63 amp, 4pole with earth fault indication protecting a circuit automatically in the event of earth leakage sensitivity 100ma, - 1 no c) fully automatic star delta starter of relay range 13-21 amp. (7.5 hp to 10 hp) 3 phase oil immersed type -1 no.d) ampere 96 x 96 mm. square shape 0-30 amp-1 no. e) voltmeter 96 x 96 mm. square shape 0-500 volt-1 no.e) indicating lamp (a set of 3 lamps) 1.setf) shunt capacitor of 10 kvar mpp type with three phase isolator with suitable banking g) motor protection assembly with earth leakage protection phase sequence corrector, single phasing, protection, overload protection, high voltage / low voltage protection time delay power on, programmable time switch i.c. r&b phase facility to change over from automatic, to manual &vice verse for up to 10 h.p -01 nos.complete wiring &installation of above accessories with required copper conductor wire and thimble etc. 01 job.make of all components: any djb approved., s/o pvc insulated and pvc sheathed cable with plain copper conductor having 3 phases, 3 core flat for submersible motor of 4 square mm size each 100 mtrs. make:grandlay / havells./any djb approved make, s/o m.s. clamp of 600 mm length duly fabricated out of 12.5 mm thick 75 mm wide, m.s. plate for holding the pipe of 50 mm dia., s/o double flange gi column pipe 50 mm dia medium class each of 3 mtrs long duly threaded on both ends, welded fitted with gi flange on both ends with slot of submersible cable. make: tata/ jindal./any djb approved make, s/o/ tail piece of the medium class gi pipe 500 mm long with one end threaded as per outlet of pump & another end flanged as per size of gi pipe 50 mm dia., s/o gi 90 bend of size 50 mm dia having both side flange (heavy duty)., supply of ms nut bolts off size as per requirement., s/o rubber packing for 50 mm dia flange., fabrication and supply supply of bore cover approx size 1x1 made out from 6mm thick m.s. sheet in 2 halves and a circular hole in centre 3-1/2 dia. with locking arrangement by nuts and bolt. , earthing with g.i. earth pipe 4.5 meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required., providing and fixing 6 swg dia g.i. wire on surface or in recess for loop earthing as required., installation of t/well by lowering of sub p/set with all allied above items. this includes installation and grouting of panel boards with all electrical wiring & cabling at site. all tools & tackles i/c. tripod chain pulley blocks etc. shall be arranged by the firm. this includes testing & commissioning of t/well on load at site i/c. cartage, loading & unloading of material. it also includes a trial run of 30 hrs operation successfully by the firm. all required civil work included in the scope of work.

Central Government/Public Sector

CTN :43504088

29 Jan, 2026 NA

Dehradune - Uttarakhand

Tender For supply of star screw driver for 4.5 mm screw with blue silicon handle shaft size-7-8 inches stainless steel

Central Government/Public Sector

CTN :43504090

29 Jan, 2026 NA

Dehradune - Uttarakhand

Tender For supply of star screw driver for 3.5 mm screw with blue silicon handle shaft size-6-7 inches stainless steel

corporations/Associations/Others

CTN :43461971

13 Jan, 2026 3.03 Lacs

Chandigarh - Chandigarh

Tender For providing and fixing of open air gym equipments in garden of annual part i of sector 44 chandigarh under wdf - providing & fixing of push chair functions: developing the strength of upper limbs, chest and muscle groups of shoulder and back, improving the flexibility and stability of shoulder joints and elbows. good for healing the bending and stretching hindrances of shoulder joints and elbows, muscular atrophy, frozen shoulder, tennis elbows, etc.approaches sit down with your back against the equipment and take hold of the handgrips with both hands and push forward with effort till your arms extend straight. revert slowly.size:-2265x662x2010 mmmaterial: pre galvanized mild steel, material thickness: 3 mm.paint: all weather double layer powder coated paint sealed ball bearing, steel seats for long lasting life. the rate shall include fixing of gym equipment in cement concrete 1:2:4 block of size 5 x 5 complete in all respects to the entire satisfaction of engineer-in-charge., providing & fixing of sur board functions: by swinging both legs together from side to side the surfing board strengthens and develops the lower abdomen hips and thighs, improves balance and co-ordination through core activation approaches: stand on the pedals and grasp the handles with both hands, swing from left to right. size:-1020x800x1480 mmmaterial: pre galvanized mild steel, material thickness: 3 mm.paint: all weather double layer powder coated paint sealed ball bearing, steel footrest / foot paddle for long lasting life.the rate shall include fixing of gym equipment in cement concrete 1:2:4 block of size 5 x 5 complete in all respects to the entire satisfaction of engineer-in-charge., providing and fixing of space walker .space walker complete in all respects having following specifications.6. all pipes should used in the equipments should be galvanised with 3mm thickness.7. multi colour powder coating with polyster paints should be used on all the equipments.8. the foot pedal on all the equipments should be of aluminium only.9. the seats should be made of high quality plastic with colour scheme in yellow or orange.10. the high end bearings such as skf/nbc must be used in all the equipments.1 dimensions- 1100*460*1480mm2 colour- customizable multi colour and complete powder coat3 size of main tube-114*3.75mm steel pipe4 size of supporting tube-38*3mm steel pipe5 there is restrainer inside, swing lever is no.t more than 65degrees and having swing rod is made of 3mm steel tube.6 al alloy protecting covers are used at the top other main tubes to protect from the rainwater7 anti-skid components are used at the pedal parts, the resistance index is greater than 0.5mm8 the distance between two pedals of the adjacent motion is no. less than 100mm.9 anti theft cover is made by stainless steel/high quality plastic10 the minimum height of the edge of swing component is no.t less than 80mm11 hazardous materials like coating agent, rubber are under national newest standard.12 radius of edge is no. less than 3.0 mm.13 the diameter of rotating shaft is no.t less than40mmfunctions: the leg & thigh exerciser provides excellent cardiovascular exercise while developing the leg muscles. allows a full range of movement in the hip joint improving flexibility and strength, without any impact or stress to joints and back. suitable for all ages. the rate shall include fixing of gym equipment in cement concrete 1:2:4 block of size 5 x 5 complete in all respects to the entire satisfaction of engineer-in-charge, providing and fixing of seated pedal trainer leg shaper complete in all respects having following specifications.6. all pipes should used in the equipments should be galvanised with 3mm thickness.7. multi colour powder coating with polyster paints should be used on all the equipments.8. the foot pedal on all the equipments should be of aluminium only.9. the seats should be made of high quality plastic with colour scheme in yellow or orange.10. the high en

corporations/Associations/Others

CTN :43480599

14 Jan, 2026 3.02 Lacs

Chandigarh - Chandigarh

Tender For providing and fixing of open air gym and pcc benches in parks near house no.2870/2 sector 49-d,chandigarh under mplads. work no.114 18th ls. - push chair odf 001functions: developing the strength of upper limbs, chest and muscle groups of shoulder and back, improving the flexibility and stability of shoulder joints and elbows. good for healing the bending and stretching hindrances of shoulder joints and elbows, muscular atrophy, frozen shoulder, tennis elbows, etc.approaches sit down with your back against the equipment and take hold of the handgrips with both hands and push forward with effort till your arms extend straight. revert slowly.size:-2265x662x2010 mm material: pre galvanized mild steel, material thickness: 3 mm.paint: all weather double layer powder coated paint sealed ball bearing, steel seats for long lasting lifeprovision for fixing of gym equipments in cement concrete 1:2:4 blocks of size 5 x5 x1 to the entire satisfaction of the engineer-in-charge, surf board by swinging both legs together from side to side the surfing board strengthens and develops the lower abdomen hips and thighs, improves balance and co-ordination through core activation approaches: stand on the pedals and grasp the handles with both hands, swing from left to right. size:-1020x800x1480 mmmaterial: pre galvanized mild steel, material thickness: 3 mm.paint: all weather double layer powder coated paint sealed ball bearing, streel footrest/foot paddle for long lasting life.provision for fixing of gym equipments in cement concrete 1:2:4 blocks of size 5 x5 x1 to the entire satisfaction of the engineer-in-charge, space walker .space walker complete in all respects having following specifications.all pipes should used in the equipments should be galvanised with 3mm thickness.multi colour powder coating with polyster paints should be used on all the equipments.the foot pedal on all the equipments should be of aluminium only.the seats should be made of high quality plastic with colour scheme in yellow or orange.the high end bearings such as skf/nbc must be used in all the equipments.1 dimensions- 1100*460*1480mm2 colour- customizable multi colour and complete powder coat3 size of main tube-114*3.75mm steel pipe4 size of supporting tube-38*3mm steel pipe5 there is restrainer inside, swing lever is not more than 65degrees and having swing rod is made of 3mm steel tube.6 al alloy protecting covers are used at the top other main tubes to protect from the rainwater7 anti-skid components are used at the pedal parts, the resistance index is greater than 0.5mm8 the distance between two pedals of the adjacent motion is no less than 100mm.9 anti theft cover is made by stainless steel/high quality plastic10 the minimum height of the edge of swing component is not less than 80mm11 hazardous materials like coating agent, rubber are under national newest standard.12 radius of edge is no less than 3.0 mm.13 the diameter of rotating shaft is not less than40mmfunctions: the leg & thigh exerciser provides excellent cardiovascular exercise while developing the leg muscles. allows a full range of movement in the hip joint improving flexibility and strength, without any impact or stress to joints and back. suitable for all ages. approaches: hold the crossbeam with both hands and swing your legs backwards and forwards in a walking motion.provision for fixing of gym equipments in cement concrete 1:2:4 blocks of size 5 x5 x1 to the entire satisfaction of the engineer-in-charge, seated pedal trainer leg shaper complete in all respects having following specifications.all pipes should used in the equipments should be galvanised with 3mm thickness.multi colour powder coating with polyster paints should be used on all the equipments.the foot pedal on all the equipments should be of aluminium only.the seats should be made of high quality plastic with colour scheme in yellow or orange.the high end bearings such as skf/nbc must be used in all the equipments.1 dimensions- 1730

Central Government/Public Sector

CTN :43484717

28 Jan, 2026 NA

Dehradune - Uttarakhand

Tender For supply of star screw driver for 2. 7 mm screw with blue silicon handle shaft size-4-5 inches stainless steel

CTN :43402074

06 Jan, 2026 NA

Multi City - Chhattisgarh

Tender For corrigendum : engineering items ( non authorized dealer)-- , aira valve auto mation ce 1128 valve automation f/b- r/b full bore end type- s/e, size dn 25mm bore seat/stem htfe 98316 bore- 25mm flanged end both side., high flow pump size- 5 inch head- 40 mtr. with motor pump or base freme, s.s. ball valve flange type size- 25mm make- aira, rubber stator for high flow pump size- 4” x 4” model no. rbh4152aabn make- risanshi, rotary screen taflon roller assembly front assembly make- uttam, juice rotary screen, rotary screen taflon roller assembly rear assembly make- uttam, juice rotary screen, rotary screen taflon roller assembly front surface assembly make- uttam, juice rotary screen, ‘b’ mescuite pump spare roter with shaft and gen metel strips pump size- 8 x 8 inch make gita pump, valency welding rod bronzocar- 32 ac/dc size- 3.15mm, valency welding rod bronzocar- 32 ac/dc size- 4.00mm, sapre tyre for following size- f- 60, sapre tyre for following size- f- 70, sapre tyre for following size- f- 80, c.i. pin bush coupling complete assembly with pin bolt with rubber bush size- 10”, c.i. pin bush coupling complete assembly with pin bolt with rubber bush size- 12”, rubber bush for pin bush coupling rubber bush size- id 19 x od 38mm x length- 40mm, en- 8 round bar size- 25mm x 4 mtr., en- 8 round bar size- 30mm x 4 mtr., en- 8 round bar size- 36mm x 4 mtr., en- 8 round bar size- 40mm x 4 mtr., coupling bolt med. en- 8 size bush bolt dia- 19mm bush length bolt- 45mm bolt caller 5mm thick- 2500, thread length- 21mm, 5/8” bsw thread with out thread- 20mm length dia- 5/8 inch, "uc-1500 type uttam make machine continuous machine spare pully housing complete assembly", "uc-1500 type uttam make machine continuous machine spare main housing assembly complete set", "uc-1500 type uttam make machine continuous machine sparebuffer chamber assembly", top scraper for mill no. 3, 4 pitch 35mm material- c.i. 1030 gr. (as per drawing) , "discharge scraper for mill no. 3, 4 pitch 35mm material- c.i. 1030 gr. (as per drawing)", b messacute pump complete 6" x 6" for b messacute without motor make risanshi, top gear transmission make model no. 2340 hbx ratio- 36, s.no. 18026797, top gear transmission make model no. 22300 hbx ratio- 37.85, s.no. 16123824, level tranmitter range - (-2150 to 0 mmh2o) supply - 10.5 to 45vdc, output - 4 to 20ma with installation & trail support warranty - 2 year make - abb/siemens/yokogawa, controller for spray enggineering panel make - winpac model no - wp - 8147 pwr - (10 to 30 vdc) with installation & trail warranty - 02 year, solenoid valve coil with hand regulator make - rotex model - mf42 - 3012x3 - 62g (3/2 way) supply - 230vac, esp level switch probe with controller and cables material - stainless steel no of parts - 4 ports, meadia type - dry material working pressure - 150°c make - eip enviro level control pvt. limited with installation & trail warranty 02 year, mix bad (mb) conductivity sensor cable with its controller work on low cell constant make- ion exchange model - indian con 5000w with installation support warranty 02 year, ph sensor cable with controller make - ion exchange model no - indion 4000 phw with installation & trail supports warranty - 02 year, touch hmi programmed display make - formaplastic model - weintexmt 5017 input power supply 24 vdc warranty - 02 year, power supply transformer make - kasunga model - dvsc 200 aem4it ( ac415/110 . 100v 200va), load cell make - minibea model - cbe1 - 50k warranty 02 year, programmed plc for batch type machine make - mitsubishi electric r5485 & lan card suported model no - fx5u-64m, programmed by formaplastic warranty - 02 year installation service support & trail work, 24 volt dc coil for solenoid valve ip - 65 make - techno as per sample provided, coil for solenoid valve supply - i-230vacol make - rotex as per sample, temprerature controller make - electronic system & devices model - esd9223 warranty - 02 year, plastic chair - ni

Central Government/Public Sector

CTN :43452254

20 Jan, 2026 10.00 Crore

Multi City - Multi State

Tender For supply of surgical d d -localizing organs on skin surface organs on skin surface after ct scan , bone cement with chlorophyll pigment , spine bone cement , vacuum mixing for bone cement , y connector for csf drainage kit , neurosurgical patties , raney clips flat shape , raney clip gun type applicator , suction irrigation device , suction tube disposable , suction tube key hole , aneurysm cliptray stainless steel , storagetray for clips and clip appliers incl lid stacking system sterilization , storagetray for yaneurysmclips stacking system made out of ppsu , storagetray for clips applier and instruments made out of ppsu for steam sterilization upto , clip remover for standard clip , clip standardtemp , applforcf minititanium clips bayonet rottitanjawdouble act , applforcf minititanium clips bayorigidtitanium jawdouble act , applying forceps for mini clips bayrotjaw angle double action , clip minitemporary slightly curved , applforc f std titanium clips bayonet rigidtitanium jaw up wards angeled , clip minitemporary , clip standardtemporaryangled , clip minitemporary curved angled closing force maxopening , applying forceps for mini clips rigid shaft rotating rigid ring handle , applying forceps for mini clips rigid shaft rotating rot ring handle , applying forceps for mini clips rigid shaft rotatingrot j ring handle , applforceps for standard clips rigid shaft rotatingrigid ring handle , applforceps for standard clips rigid shaftrotatingrigid ring handle , applforceps for standard clips rigid shaft rotrotjaws ring handle , appl forceps for standard clips rigid shaft rotating rot ja ring handle , applying forceps for mini clips forceps handle bayonet rigid jaw , clip standard perm. fen , clip standard permanent angled , clip standard perm template combined orbital floor plate, template orbital floor plate large, orbita floor plates, orbita floor plate right small, orbita floor plate right large, orbita floor plate left small, orbita floor plate left large, standard plates profile, hole straight plate, hole straight plate, hole l plate deg left, hole l plate deg right, t plate holes, hole double y plate, hole orbital plate, hole curved plate, burr hole cover plate, burr hole cover plate, burr hole cover plate, burr hole cover plate, orbital floor plate complex large, orbital floor plate complex large, orbital floor plate complex large, template combined orbital floor plate, dynamic mesh, dynamic mesh, dynamic mesh, dynamic mesh, dynamic mesh, dynamic mesh, dynamic mesh, dynamic mesh, titanium bone screws, titanium bone screws, titanium bone screws, titanium bone screws, titanium bone screws, emergency screws, titanium bone self drilling screws, titanium bone self drilling screws, titanium bone self drilling screws, titanium bone self drilling screws, titanium bone self drilling screws, drill bit, twist drill, twist drill, twist drill, mid face fixation implants, hole plate with bar, hole plate with bar, hole plate with bar, hole plate with bar, hole curved plate, hole curved plate, hole curved plate, tplate holes, yplateholes //bid details2 / 124

CTN :43306178

31 Jan, 2026 NA

Mumbai - Maharashtra

Tender For corrigendum : tender for supply of shaft chain pinions , bearing sleeve , chain pinion , chain pinion , sheave shaft , tie bar , chain 3mm , bush , bush , main drive shaft , abeam fas rig loose tackle stbd , clutch cover bush , barrel shaft , gearcase bedplate , terminal box , no 2 trough wire 18mm dia 6x36 steel wire rope , no 4 trough wire 14mm dia 6x36 steel wire rope , o ring , control valve 2 , elastic ring coupling 42 55 , locking plate , slipping clutch plate , bush , clutch cover bush , sliding clutch , pinion , spindle , pinion shaft , drain plug , cover joint , roller pin , roller bush , sheave bracket shaft , bush , vertical roller , horizontal roller , pivot pin , spring guide shaft , bush , jackstay sheave bracket assy lh , roller bracket , brake strap , brake strap , bush , brake strap , brake strap , brake strap , locknut bearing , filter suction 1 1 2 , breather filter , filter ttf , low level switch , bearing taper roller , operators chair , split cotter pin 3 16 x3 5 , swivel and links , disc spring , split pin stainless st , dowty washer 3 4 bsp , directional valve , directional valve , pressure switch , motor coupling , filler breather , suction element , bearing , bearing , bearing , taper roller bearing , v seal , double hose trough , straight shackle size 32mm , sheave block 406 0 dia 346 dia bog , tunnel block , 4 leg sling , deep groove ball bearing , spherical roller bearings , spherical roller bearings , chain , motor terminal box seal , motor terminal box cover seal , motor terminal box seal , motor terminal box seal , motor terminal box seal , motor brake friction disc , input module 890px 3ph 500v 400kw , internal seals

CTN :43436645

13 Jan, 2026 NA

Pune - Maharashtra

Tender For supply of mt spares d d - lv7 t-815 hmv 443-612-226-005 trg aggr main brake valve , lv7 t-815 336-631-105-303 high pressure hose 8x250 hv-1m , lv7 t-815 150-240-024-003 socket wrench assy , lv7 t-815 4x4 442-999-513-000 clutch cover-mzf , lv7 t-815 4x4 990-100-950-000 pack rectifire -0139291 , lv7 tata 000-151-0114j brush set 4 , lv7 tata 2154-3020-0101 assy pull cable , lv7 tata 270754249907 wiper timer 24v , lv7 tata 2154-42700102 assy hose , lv7 tata 2641-7520-0112 assy release cable comp. centre flap , lv7 tata 26147061-0102 assy water tank , lv7 tata 2085-4680-0101 assy hose , lv7 tata 2641-7250-2301 door glass lh , lv7 tata dld-nnk-13-14 stainless steel bolt m6x20 long with nyl , lv7 tata 2574-5442-0104 assy tail lamp lh , lv7 tata 2654-7231-0119 door lock front rh , lv7 tata 2069-5010-5834 rubber hose , lv7 tata 2573-2910-0160 minor repair kit for m cyl consisting of , lv7 tata 2654-7230-0124 assy outer handle lh , lv7 tata t-257346200115 input shaft seal kit

Propeller Shaft Assembly Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

State Government

Central Government/Public Sector

Central Government/Public Sector

corporations/Associations/Others

corporations/Associations/Others

Central Government/Public Sector

Central Government/Public Sector