Latest pvc coil Tenders | Government pvc coil Tenders

Central Government/Public Sector

CTN :40809830

07 Jul, 2025 NA

Kanakapura - Karnataka

Tender For supply of ferritic steel sheet 6x1250x3500mm., as per drawing: rdso spec no.c-k201, gra de x2crni12 (409m) table 1&2. heat treatment condition 2d as per table-5., packing instructi on: stainless steel sheets, coils and plates:- (a) stainless steel (austenitic & ferritic ste el) coils. the coil shall be protected in reasonably good condition to withstand norm al handling hazard during transit with the following provision as the barest minimum: i) coil should be wrapped with a layer of water proof paper through out whole length. ii) coil should be wrapped with a layer of biodegradeable sheet. iii) outer & inne r of coil should be wrapped with gi sheet. iv) side of the coil should be covered with c ard board sheet. v) after this whole coil should be wrapped with biodegradeable plast ic sheet of suitable thickness. vi) the inner edge of the coil should be protected by gi r ing followed by another iron ring. vii) outer edge of the coil should be wrapped with gi ring. viii) coil should be securely strapped with minium 5 steel bands through the eye s of the coil and minium 3 steel bands on the circumference of the eye. ix) whole coil s hould be mounted on wooden blocks for easy lifting/stacking. x) the sheets in coil for m for thickness 2mm and above shall have: inner dia of coil 450-800mm outer dia of coil 1000-1300mm weight of coil 2.4 - 10 tonnes xi) the sheets in coil form for thickness belo w 2mm shall have: inner dia of coil 450-650mm outer dia of coil 1000-1300mm weight of c oil 5.0 - 10 tonnes. (b) stainless steel (austenitic & ferritic steel plates/sheets) i) the sh eets/plates shall be supplied in bundles of optimum weight: 2mt+/-10% & each sheet/plat e shall be seprated with a layer of water proof paper, after this the whole bundle sho uld be wrapped with double layer of water proof paper and a biodegradeable plastic s heet of suitable thickness. a metal protection in edges should also be provided. ii) all bundles shall have a minimum of 2 hoops upto 1.2 meter in length and one extra hoop f or every additional meter. the bundles shall also be provided with skid (wooden packi ng under neath) to facilitate handling. mechanical damange & corrosion during transi t if any shall be at the cost of supplier. , proction procedure: covered in pi [ warranty perio d: 30 months after the date of delivery ]

State Government

CTN :40616761

27 Jun, 2025 NA

Thiruvananthapuram - Kerala

Tender For corrigendum : name of work supply of hardware - supply of hardware, 6mm 1inch length gypsum screw(packet of 1000nos)as per annexure 6, 6mm 3inch length gypsum screw(packet of 100nos), 6mm 1inch length stainless steel screw(packet of 100nos), 8mm 1.5inch length stainless steel screw(packet of 100nos), 6mm 1.5inch length stainless steel screw(packet of 100nos), 6mm 1inch pvc fastner(packet of 100nos), 8mm 1.5inch pvc fastner(packet of 50nos), 6mm x 75mm steel fastner, 8mm x 75mm steel fastner, 10mm x 75mm steel fastner, 25mm x 3 mm bolts and nuts with washers, 38mm x 8 mm bolts and nuts with washers, 38mm x 10 mm bolts and nuts with washers, 50mm x 10 mm bolts and nuts with washers, 75mm x 10 mm bolts and nuts with washers, 75mm x 14 mm bolts and nuts with washers, 75mm x 16 mm bolts and nuts with washers, gi saddles for 15mm conduits(288 nos. per box), gi heavy duty saddles for 20mm conduits(144 nos. per box), gi heavy duty saddles for 25mm conduits (144 nos. per box), 2.5sqmm copper pin terminal lugs (insulated), 4sqmm copper pin terminal lugs (insulated), 6sqmm copper pin terminal lugs (insulated), 10sqmm copper pin terminal lugs (insulated), 16sqmm copper pin terminal lugs (insulated), 2.5sqmm copper ring terminal lugs (insulated), 4sqmm copper ring terminal lugs (insulated), 6sqmm copper ring terminal lugs (insulated), 10sqmm copper ring terminal lugs, 16sqmm copper ring terminal lugs, 25sqmm copper ring terminal lugs, 35sqmm copper ring terminal lugs, 70sqmm copper ring terminal lugs, 95sqmm copper ring terminal lugs, 120sqmm copper ring terminal lugs, 150sqmm copper ring terminal lugs, 10sqmm aluminium ring terminal lugs, 16sqmm aluminium ring terminal lugs, 25sqmm aluminium ring terminal lugs, 35sqmm aluminium ring terminal lugs, 50sqmm aluminium ring terminal lugs, 70sqmm aluminium ring terminal lugs, 95sqmm aluminium ring terminal lugs, 120sqmm aluminium ring terminal lugs, 150sqmm aluminium ring terminal lugs, 185sqmm aluminium ring terminal lugs, 240sqmm aluminium ring terminal lugs, 300sqmm aluminium ring terminal lugs, 16sqmm aluminium pin terminal lugs, 25sqmm aluminium pin terminal lugs, 35sqmm aluminium pin terminal lugs, 50qmm aluminium pin terminal lugs, nylon cable tie 4inch length (100nos.per pkt), nylon cable tie 6inch length (100nos.per pkt), nylon cable tie 8inch length (100nos.per pkt), nylon cable tie 10inch length (100nos.per pkt), nylon cable tie 12inch length (100nos.per pkt), led indication lamp for mv panel application (red), led indication lamp for mv panel application (yellow), led indication lamp for mv panel application (blue), led indication lamp for mv panel application (green), led indication lamp for mv panel application (amber), 20mm upvc flexible pipe with steel wire rerinforcement (polycab/precision/akg/balco or equivalent)(30mtr per coil), 25mm upvc flexible pipe with steel wire rerinforcement (polycab/precision/akg/balco or equivalent) (30mtr per coil), 20mm upvc steel wire rerinforcement conduit gland, 20mm upvc steel wire rerinforcement conduit gland

State Government

CTN :40808390

30 Jun, 2025 NA

Mehmedabad - Gujarat

Tender For in house preparations of earthing coil from gi wire no.8 at mehmedabad division premises

CTN :40478030

26 Jun, 2025 NA

Jalandhar - Punjab

Tender For bid to ras supply of generator spare parts - air cleaner assy for genr set 2 kva as per sample , air cleaner assy for genr set 15 kva make bosch kirloskar cummins and tvs , air filter for genr set 62 point 5 kvamake bosch kirloskar cummins and tvs , air filter assy for genr set 30 kva make mico kirloskar cummins and tvs , air filter for genr set 2 kva as per sample , benjo bolt 19mm for genr set 30 kva as per sample , benjo union 19mm for genr set 15 kva , benjo washer 19mm for genr set 30 kva as per sample , bty 12 v 150 ah for genr set 30 kva make exide gold exide express tata and amron , cap for sparking plug for genr set 2 kva as per sample , carboretor assy complete for genr set 2 kva make bosch kirloskar and cummins , carboretor repair kit for genr set 2 kva as per sample , flexible exhaust as per sample for genr set 30 kva , fuel filter for genr set 62 point 5 kva make bosch kirloskar cummins and tvs , fuel filter primary and secondary for genr set 30 kva water cooled make bosch kirloskar and cummins , fuel flexible pipe for genr set 30 kva as per sample , fuel pipe rubber type for genr set 2 kva as per sample , hose rubber fuel pipe 2 inch long for genr set 30 kva make bosch kirloskar and cummins , ht coil for genr set 2 kva as per sample , ignitor switch for genr set 15 kva as per isi marked , indicator lamp for genr set 30 kva as per sample , oil pressure pipe long for genr set 30 kva make bosch kirloskar cummins and tvs , over flow pipe line for genr set 62 point 5 kva make bosch kirloskar cummins and tvs , plug for sparking plug for genr set 2 kva make bosch kirloskar and cummins , pre fuel filter for fuel tank for genr set 2 kva as per sample , radiator hose complete set for genr set 62 point 5 kva , starting rope assembly for genr set 2 kva make bosch kirloskar and cummins , oil filter for genr set 62 point 5 kva make bosch kirloskar cummins and tvs , armature for genr set 30 kva , panel board for genr set 250 kva 3 phase , mccb 400 amps model dn 3b 400d , digital meter dt 36l make nippen bosch cummins , change over switch co2 200 amp make lauriz knudsen tvs bosch , cable 3 point 5 core 300 sqm alluminium , bus bar 200amp , copper wire 75mm single core , thimble 300mm , thimble 75 mm , empire tape roll , gi pipe 20mm dia as per isi mark , pvc elbow 110mm , pvc socket 110mm , pvc pipe 110mm 3 mtr long , sintex rectangular with lid capacity of 200 ltrs

CTN :40802026

12 Jul, 2025 NA

Pithoragarh - Uttarakhand

Tender For supply of weld mesh panels should produced by electrical resistance welded galvanized wires and subsequently powder coated , concertina coil 1050 mm dia oblique 56 loops oblique 2 point 5 mm core wire oblique coil diameter 1050 mm , fence post circular hollow material ms steel tube is 1161 , omega clamp with profile cover plate to tighten the mesh panel along the posts with diameter 76 mm and 35mm width and 3mm thick flat 35mm width and 3mm thick , straining y arm for supporting top ptcc material ms angle size 50x50x5 mm , high tensile barbed wire high tensile heavy galvanised mild steel wire for line wire and high tensile barb wire is made of higher carbon steel approximately 0 point 28 percent , anchor rod 10 mm dia 300mm long gi rod tie with fence post at bottom using tie wire , nut and bolt a mushroom head nut and bolt m8 120mm , nut and bolt b mushroom head nut and bolt m8 50mm , cement in polythene bags 50 kgs each 43 opc , coarse sand , stone aggregate shall be crushed stone 20mm graded , stone aggregate shall be crushed stone 40mm graded , solar street light 25 w including pole having length 5 mtr long and 75 mm dia and complete accessories warranty for street lighting system min 2 years , binding wire 20 gauge 0 and 9 mm annealed , shuttering plywood of size 6 x 4 feet and 12mm thickness , nails 2 inch for shuttering , nails 3 inch for shuttering , nails 4 inch for shuttering , 2nd class hardwood plain fillets 3mtr long and section 50mm x 50mm , wooden scantling 3mtr long section 100mm x 75mm , quick setting compound , acrylic emulsian paint , cost of construction

State Government

CTN :40772511

26 Jun, 2025 9.65 Lacs

Kangra - Himachal Pradesh

Tender For tender for supply of equipment / material, design, erection, testing, commissioning for providing s.o.p. to newly constructed residential building at nift campus chebb at kangra under esd no. i hpsebl, kangra. - (a) material/erection of 11/0.4kv,250 kva s/stn., prov.distribution transformer (ordinary), 11/0.4 kv, 250 kva, prov.steel tubular poles (9 m, working load > 200 kgf/m ), prov.x-arm: [channel iron (100x50x5 mm), length : 2800 mm x 2 nos] for incomer line, prov.ms angle iron (50x50x6 mm), length: (2800 mm) x1 nos for las, prov.x-arm: [channel iron (75x40x6 mm), length : (2800 mm x 4 nos] for supporting do fuse unit & go switch, prov.x-arm: [channel iron (100x50x5 mm), length : 2800 mm x 2 nos] for transformer bed, prov.x-arm [channel iron (100x50x5 mm), length : (460 mm) x 2 nos for supporting main channel of transformer], prov.ms angle iron (50x50x6 mm), length : (2800 mm) x 2 nos, prov.ms angle iron (35x35x6 mm), length : (460 ) x 2 nos, prov.ms angle iron (50x50x6 mm), length : (950 mm) x 2 nos for bed knee bracing, prov.ms angle iron (50x50x6 mm), length : (2800 mm) x 2 nos, prov.ms angle iron (50x50x6 mm), length : (450 mm) x 1 nos, prov.go switch handle supporting: [channel iron (75x40x6 mm), length : 460 mm, prov.d.o fuse unit, prov.surge arrester, 9 kv station class (porcelain type), prov.discs insulator sets (comprising 1 no. disc: ^^(porcelain, bs, 12kv, 90 kn) including dead end clamps etc.), prov.pipe earthing set, lt distribution panel box with mccb(630a, 50 ka, 3p,1 no) and mccb(250 a, 36ka, 3p, 3 no.), prov.half clamp (m.s. flat 50x6 mm), prov.full clamps (m.s. flat 50x6 mm), prov.nuts and bolts of various sizes (galvanised / coated) [preferably 16 mm or more (with flat and spring washers)], aluminium thimble, copper thimble 200 amp, danger plate, prov.barbed wire, prov.energy meter (3-phase,4-wire)dlms compliant 400/5a ct type, prov. aluminium paint., prov.aaac 7/3.15mm conductor for earthing, erection charges complete in all respect, transportation charges complete in all respect, (b)material/erection of 11 kv ht line, prov aaac 7/3.15mm conductor (50mm ) {includes cutting and wastage}, prov. steel tubular poles (9 m, working load > 200 kgf/m ), prov.m.s. c.i.x-arm (1500x100x50x5 mm), long for single pole, prov.m.s a.i x-arm (1800x50x50x6 mm), long for single pole, prov m.s a.i x-arm (50x50x6 mm), length (2x750) mm long for single pole, prov m.s a.i x-arm (50x50x6 mm),length (2x600) mm long for single pole, prov.m.s c. i cross arm (75x40x5 mm), length (2400) mm for g.o switch & d.o fuses, prov.belt set - ms a.i 50x50x6, length [2400 mm x 2 no.] for double pole, prov.x-bracing set - ms a.i 50x50x6, length [2700 mm x 2 no.]for double pole, prov 11 kv pin insulators (porcelain, 12 kv, 10 kn), prov disc insulator ,1 no disc (12 kv, 90 kn) including dead end clamps etc., prov ht earthing set complete, prov double continous earth wire (gi, 8 swg) @ 0.102 kg/m, prov danger plate (250x200x1.6 mm), prov nuts and bolts of various sizeswith flat and spring washers, prov barbed wire, prov aluminium paint, prov.full clamps (m.s. flat 50x6 mm), prov.xerox for chebb s/stn for scada, prov.d.o fuse unit, erection charges of 9 mtr st pole complete in all respect, erection charges of stay set complete in all respect, erection charges of coil earthing complete in all respect, erection charges of g.o. switch complete in all respect, erection charges of sagging aaac 7/3.15mm conductor, sagging of continous earth wire (gi, 8swg) @ 0.102 kg/m complete in all respect, transportation charges complete in all respect, commissioning of a 250 kva dtr plinth and fencing, earth work in excavation by mechanical means (hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. all kinds o

State Government

CTN :40798425

30 Jun, 2025 NA

Mehmedabad - Gujarat

Tender For in house preparations of earthing coil from gi wire no.8 at mehmedabad division premises

CTN :40791917

27 Jun, 2025 27.52 Lacs

Delhi - Delhi

Tender For upgradation works of defence pool bungalows occupied by defence pool officers under csd during 2025-26 (sh: provision of rain water line, cabin for security guard, wall panelling etc. at 8a, janpath road and concertina coil, barricading by g.i. profile sheet etc. at 3 kk marg, new delhi & other bungalows)

CTN :40793274

12 Jul, 2025 NA

Chennai - Tamil Nadu

Tender For supply of 2,5 sq mm wire coil r-3,y-3,bl-2,bla-4,g-3 , 10sq mm wire , 1 inch pvc pipe , 8 way db box , 4 pole 40a isolator , 20a single pole breaker , ac box , 1 inch bend , 1 inch flexible hose , 1 inch gi clamp , 1 inch screw , plug wood , 1 1-2 screw , spring box , 6mm drill bit , aksha blade , insulation tape re-5,ye-5,bl-5, bla-5,gr-5 , cable tie 250-4.8 , 1.5wire , 12 model box , 12 model plate , 5amps switch , 5amps socket , 3-4 casing capping , 3-4 screw , plug wood , dril pit , insulation tape , aksha blade , 2.5 mfd fan capacitor , stabilizers , pedestal fans , ceiling fans , drawer locks , teapoy , air purifier , steel almirah , roller blinds

Central Government/Public Sector

CTN :40770421

10 Jul, 2025 NA

Rupnagar - Punjab

Tender For supply of supply of fan coil unit 3tr 1200 cfm , i t c of fan coil unit 3tr 1200 cfm , supply of ms c class pipe size 40 nb complete with fittings nut bolts flanges , i t c of ms c class pipe size 40 nb complete with fittings nut bolts flanges , supply of ms c class pipe size 25 nb complete with fittings nut bolts flanges , i t c of ms c class pipe size 25 nb complete with fittings nut bolts flanges , supply of gi b class drain piping with size 15 nb complete with u trap fittings , i t c of gi b class drain piping with size 15 nb complete with u trap fittings , supply of y strainer with ss filter element size 25 nb , i t c of y strainer with ss filter element size 25 nb , supply of thermostat for fcu fan on off control , i t c of thermostat for fcu fan on off control , supply of ball valve size 25 nb pn10 butt welded connections ss ball cs body , i t c of ball valve size 25 nb pn10 butt welded connections ss ball cs body , supply of ball valve size 40 nb pn10 butt welded connections ss ball cs body , i tc of ball valve size 40nb pn10 butt welded connections ss ball cs body , supply of ms supporting structure for piping , i t c of ms supporting structure for piping , supply of 18mm nitrile insulation class 0 aluminium faced sections sleeves for glycol and drain piping , i tc of 18mm nitrile insulation class 0 aluminium faced sections sleevss for glycol and drain piping

Pvc Coil Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

Central Government/Public Sector

State Government

State Government

State Government

State Government

Central Government/Public Sector